scholarly journals Enhanced Current Reference Calculation to Avoid Harmonic Active Power Oscillations

Energies ◽  
2019 ◽  
Vol 12 (21) ◽  
pp. 4075 ◽  
Author(s):  
Javier Serrano ◽  
Javier Moriano ◽  
Mario Rizo ◽  
Francisco Dongil
Keyword(s):  
Harmonic Distortion ◽  
Low Frequency ◽  
Active Power ◽  
Computational Time ◽  
Time Step ◽  
Peak Current ◽  
Current Harmonic ◽  
Grid Voltage ◽  
Current Reference ◽  
Power Oscillations

Energy storage systems play a key role in the rise of distributed power generation systems, hence there is great interest in extending their lifetimes, which are directly related to DC current ripple. One of the ripple sources is the low-frequency active power fluctuations under unbalanced and distorted grid voltage conditions. Therefore, this paper addresses a multifrequency control strategy where the harmonic reference currents are calculated to reduce harmonic active power oscillations. The stationary reference frame (StRF) approach taken here improves the precision and computational time of the current reference calculation method. Additionally, in order to ensure safe converter operation when a multifrequency reference current is provided, a computational efficient peak current saturator is applied while avoiding signal distortion every time step. If the injected current harmonic distortion is to be minimized, which is a feature included in this work, the peak current saturator is a necessary requirement. Active power ripple is reduced even with frequency variations in the grid voltage using a well-known frequency-adaptive scheme. The simulation and experimental results prove the optimized performance for the control objective: power ripple reduction with minimum current harmonic distortion.

scholarly journals The Performance of the BTB-VSC for Active Power Balancing, Reactive Power Compensation and Current Harmonic Filtering in the Interconnected Systems

Energies ◽  
2020 ◽  
Vol 13 (4) ◽  
pp. 831 ◽  
Author(s):  
Janeth Alcalá ◽  
Víctor Cárdenas ◽  
Alejandro Aganza ◽  
Jorge Gudiño-Lau ◽  
Saida Charre
Keyword(s):  
Reactive Power ◽  
Harmonic Distortion ◽  
Reactive Power Compensation ◽  
Active Power ◽  
Performance Criteria ◽  
Voltage Source ◽  
Voltage Source Converter ◽  
Current Harmonics ◽  
Current Harmonic ◽  
Harmonic Filtering

Nowadays, the use of power converters to control active and reactive power in AC–AC grid-connected systems has increased. With respect to indirect AC–AC converters, the tendency is to enable the back-to-back (BTB) voltage source converter (VSC) as an active power filter (APF) to compensate current harmonics. Most of the reported works use the BTB-VSC as an auxiliary topology that, combined with other topologies, is capable of active power regulation, reactive power compensation and current harmonic filtering. With the analysis presented in this work, the framework of the dynamics associated with the control loops is established and it is demonstrated that BTB-VSC can perform the three tasks for which, in the reviewed literature, at least two different topologies are reported. The proposed analysis works to support the performance criteria of the BTB-VSC when it executes the three control actions simultaneously and the total current harmonic distortion is reduced from 27.21% to 6.16% with the selected control strategy.

Is Hydraulics Over-Used or Under-Used in Storm Drainage?

1994 ◽  
Vol 29 (1-2) ◽  
pp. 53-61
Author(s):  
Ben Chie Yen
Keyword(s):  
Unsteady Flow ◽  
Computational Time ◽  
Time Step ◽  
Flow Routing ◽  
Kinematic Wave Equation ◽  
Storm Drainage ◽  
Saint Venant Equations ◽  
Unsteady Flow Routing ◽  
Selection Of

Urban drainage models utilize hydraulics of different levels. Developing or selecting a model appropriate to a particular project is not an easy task. Not knowing the hydraulic principles and numerical techniques used in an existing model, users often misuse and abuse the model. Hydraulically, the use of the Saint-Venant equations is not always necessary. In many cases the kinematic wave equation is inadequate because of the backwater effect, whereas in designing sewers, often Manning's formula is adequate. The flow travel time provides a guide in selecting the computational time step At, which in turn, together with flow unsteadiness, helps in the selection of steady or unsteady flow routing. Often the noninertia model is the appropriate model for unsteady flow routing, whereas delivery curves are very useful for stepwise steady nonuniform flow routing and for determination of channel capacity.

PI and Fuzzy-Controlled 3-Phase 4-Wire Interleaved Buck Active Power Filter with Shoot-Through Elimination for Power Quality Improvement using RTDS Hardware

2014 ◽  
Vol 15 (2) ◽  
pp. 177-194 ◽  
Author(s):  
Anup Kumar Panda ◽  
Ranjeeta Patel
Keyword(s):  
Control Strategy ◽  
Fuzzy Logic Controller ◽  
Supply Voltage ◽  
Harmonic Distortion ◽  
Active Power Filter ◽  
Active Power ◽  
Current Harmonics ◽  
Power Filter ◽  
Power Quality Improvement ◽  
Real Time Digital Simulator

Abstract In this paper, shoot-through current elimination DC–AC converter circuit has been presented with the application of active power filter (APF). The intuitive analysis of the shoot-through in the conventional DC–AC converter has been reported first. Interleaved buck (IB) converter is adopted to eliminate the shoot-through current, thereby increasing the reliability of the interleaved buck–based active power filter (IB-APF). The 3-phase 4-wire IB-APF eliminates the current harmonics produced by the load just as a conventional one does and are innately immune to “shoot-through” phenomenon, with the elimination of special protection features required in conventional inverter circuits. A comparison has been made about the compensation capabilities of the IB-APF with the PI and fuzzy logic controller (FLC) used by id–iq control strategy under different supply voltage conditions. The id–iq control strategy used for extracting the three-phase reference current for IB-APF, evaluating their performance here in MATLAB/Simulink environment and also implemented using real-time digital simulator hardware (OPAL-RT hardware). The RTDS result verifies that the total harmonic distortion percentage of the source current can be reduced below 5% according to IEEE-519 standard recommendations on harmonic limits.

Ant Colony Algorithm (ACO) Applied for Tuning PI of Shunt Active Power Filter (SAPF)

2021 ◽  
Vol 17 (2) ◽  
pp. 204-211
Author(s):  
Raheel Jawad ◽  
Rawaa Jawad ◽  
Zahraa Salman
Keyword(s):  
Ant Colony Algorithm ◽  
Electrical Power ◽  
Harmonic Distortion ◽  
Electrical Energy ◽  
Active Power ◽  
Ant Colony ◽  
Electrical Strength ◽  
Shunt Active Power Filter ◽  
Active Power Filters ◽  
Non Linear

In the present-day decade, the world has regarded an expansion in the use of non-linear loads. These a lot draw harmonic non-sinusoidal currents and voltages in the connection factor with the utility and distribute them with the useful resource of the overall performance of it. The propagation of these currents and voltages into the grids have an effect on the electricity constructions in addition to the one of various client equipment. As a result, the electrical strength notable has come to be critical trouble for each client and distributor of electrical power. Active electrical electricity filters have been proposed as environment splendid gear for electrical power pinnacle notch enchantment and reactive electrical strength compensation. Active Power Filters (APFs) have Flipped out to be a possible wish in mitigating the harmonics and reactive electrical electricity compensation in single-phase and three-phase AC electrical energy networks with Non-Linear Loads (NLLs). Conventionally, this paper applied Ant Colony Algorithm(ACO) for tuning PI and reduce Total Harmonic Distortion (THD). The result show reduces THD at 2.33%.

On the Friction Coefficient in the Numerical Simulation of Tidal Wave Propagation

2010 ◽  
Author(s):  
Z. Y. Song ◽  
C. Cheng ◽  
F. M. Xu ◽  
J. Kong
Keyword(s):  
Numerical Simulation ◽  
Wave Propagation ◽  
Friction Factor ◽  
Tidal Wave ◽  
Computational Time ◽  
Numerical Dissipation ◽  
Courant Number ◽  
Time Step ◽  
Large Time Step ◽  
The Relationship

Based on the analytical solution of one-dimensional simplified equation of damping tidal wave and Heuristic stability analysis, the precision of numerical solution, computational time and the relationship between the numerical dissipation and the friction dissipation are discussed with different numerical schemes in this paper. The results show that (1) when Courant number is less than unity, the explicit solution of tidal wave propagation has higher precision and requires less computational time than the implicit one; (2) large time step is allowed in the implicit scheme in order to reduce the computational time, but the precision of the solution also reduce and the calculation precision should be guaranteed by reducing the friction factor: (3) the friction factor in the implicit solution is related to Courant number, presented as the determined friction factor is smaller than the natural value when Courant number is larger than unity, and their relationship formula is given from the theoretical analysis and the numerical experiments. These results have important application value for the numerical simulation of the tidal wave.

A General Rezoning Technique for KIVA3V Internal Combustion Engines CFD Simulations

2010 ◽  
Author(s):  
Randy P. Hessel ◽  
Ettore Musu ◽  
Salvador M. Aceves ◽  
Daniel L. Flowers
Keyword(s):  
Combustion Chamber ◽  
Internal Combustion Engines ◽  
Ad Hoc ◽  
National Laboratory ◽  
Internal Combustion ◽  
Computational Time ◽  
Combustion Engines ◽  
Combustion Chambers ◽  
Time Step ◽  
Engine Cycle

A computational mesh is required when performing CFD-combustion modeling of internal combustion engines. For combustion chambers with moving pistons and valves, like those in typical cars and trucks, the combustion chamber shape changes continually in response to piston and valve motion. The combustion chamber mesh must then also change at each time step to reflect that change in geometry. The method of changing the mesh from one computational time step to the next is called rezoning. This paper introduces a new method of mesh rezoning for the KIVA3V CFD-combustion program. The standard KIVA3V code from Los Alamos National Laboratory comes with standard rezoners that very nicely handle mesh motion for combustion chambers whose mesh does not include valves and for those with flat heads employing vertical valves. For pent-roof and wedge-roof designs KIVA3V offers three rezoners to choose from, the choice depending on how similar a combustion chamber is to the sample combustion chambers that come with KIVA3V. Often, the rezoners must be modified for meshes of new combustion chamber geometries to allow the mesh to successfully capture change in geometry during the full engine cycle without errors. There is no formal way to approach these modifications; typically this requires a long trial and error process to get a mesh to work for a full engine cycle. The benefit of the new rezoner is that it replaces the three existing rezoners for canted valve configurations with a single rezoner and has much greater stability, so the need for ad hoc modifications of the rezoner is greatly reduced. This paper explains how the new rezoner works and gives examples of its use.

scholarly journals Comparison of numerical schemes of river flood routing with an inertial approximation of the Saint Venant equations

RBRH ◽  
2018 ◽  
Vol 23 (0) ◽  
Author(s):  
Alice César Fassoni-Andrade ◽  
Fernando Mainardi Fan ◽  
Walter Collischonn ◽  
Artur César Fassoni ◽  
Rodrigo Cauduro Dias de Paiva
Keyword(s):  
Numerical Stability ◽  
Flood Routing ◽  
Computational Time ◽  
Numerical Schemes ◽  
Time Step ◽  
Simple Formulation ◽  
One Dimensional ◽  
Saint Venant Equations ◽  
Original Scheme ◽  
The One

ABSTRACT The one-dimensional flow routing inertial model, formulated as an explicit solution, has advantages over other explicit models used in hydrological models that simplify the Saint-Venant equations. The main advantage is a simple formulation with good results. However, the inertial model is restricted to a small time step to avoid numerical instability. This paper proposes six numerical schemes that modify the one-dimensional inertial model in order to increase the numerical stability of the solution. The proposed numerical schemes were compared to the original scheme in four situations of river’s slope (normal, low, high and very high) and in two situations where the river is subject to downstream effects (dam backwater and tides). The results are discussed in terms of stability, peak flow, processing time, volume conservation error and RMSE (Root Mean Square Error). In general, the schemes showed improvement relative to each type of application. In particular, the numerical scheme here called Prog Q(k+1)xQ(k+1) stood out presenting advantages with greater numerical stability in relation to the original scheme. However, this scheme was not successful in the tide simulation situation. In addition, it was observed that the inclusion of the hydraulic radius calculation without simplification in the numerical schemes improved the results without increasing the computational time.

Sign in / Sign up

Export Citation Format

Share Document