scholarly journals Combustion and Emission Reduction Characteristics of GTL-Biodiesel Fuel in a Single-Cylinder Diesel Engine

Energies ◽  
2019 ◽  
Vol 12 (11) ◽  
pp. 2201 ◽  
Author(s):  
Kibong Choi ◽  
Suhan Park ◽  
Hyun Gu Roh ◽  
Chang Sik Lee
Keyword(s):  
Diesel Engine ◽  
Emission Reduction ◽  
Cetane Number ◽  
Experimental Results ◽  
Biodiesel Fuel ◽  
Injection Timing ◽  
Nox Emissions ◽  
Biodiesel Blends ◽  
Reduction Characteristics ◽  
Blended Fuels

The purpose of this paper is to investigate the effects of using gas to liquid (GTL)-biodiesel blends as an alternative fuel on the physical properties as well as the combustion and emission reduction characteristics in a diesel engine. In order to assess the influence of the GTL-biodiesel blending ratio, the biodiesel is blended with GTL fuel, which is a test fuel with various blending ratios. The effects of GTL-biodiesel blends on the fuel properties, heat release, and emission characteristics were studied at various fuel injection timing and blending ratios. The test fuels investigated here were GTL, biodiesel, and biodiesel blended GTL fuels. The biodiesel blending ratio was changed from 0%, 20% and 40% by a volume fraction. The GTL-biodiesel fuel properties such as the fuel density, viscosity, lower heating value, and cetane number were analyzed in order to compare the effects of different mixing ratios of the biodiesel fuel. Based on the experimental results, certain meaningful results were derived. The increasing rate of the density and kinematic viscosity of the GTL-biodiesel blended fuels at various temperature conditions was increased with the increase in the biodiesel volumetric fraction. The rate of density changes between biodiesel-GTL and GTL are 2.768% to 10.982%. The combustion pressure of the GTL fuel showed a higher pressure than the biodiesel blended GTL fuels. The biodiesel-GTL fuel resulted in reduced NOx and soot emissions compared to those of the unblended GTL fuel. Based on the experimental results, the ignition delay of the GTL-biodiesel blends increased with the increase of the biodiesel blending ratio because of the low cetane number of biodiesel compared to GTL. As the injection timing is advanced, the NOx emissions were significantly increased, while the effect of the injection timing on the soot emission was small compared to the NOx emissions. In the cases of the HC and CO emissions, the GTL-biodiesel blended fuels resulted in similar low emission trends and, in particular, the HC emissions showed a slight increase at the range of advanced injection timings.

scholarly journals Experimental Investigation of Diesel Engine with Novel Juliflora Biodiesel

2020 ◽  
Vol 10 (1) ◽  
pp. 138-145
Keyword(s):  
Experimental Investigation ◽  
Diesel Engine ◽  
Vegetable Oils ◽  
Diesel Fuel ◽  
Alternative Fuel ◽  
Experimental Results ◽  
Nox Emissions ◽  
Viable Option ◽  
Biodiesel Blends ◽  
Petroleum Fuels

Biodiesels which have been derived from non-edible vegetable oils are bagging the interest of researchers. These have been recognized as the potential alternatives of regular petroleum fuels. In this work, oil extracted from Juliflora seeds is converted as biodiesel by the transesterification process and used as alternative fuel in diesel engines. The tests are conducted by using diesel, B10, B20, B30 and B40. The experimental results of this study have disclosed that the Juliflora biodiesel blends have shown similar characteristics as diesel fuel. The BTE, CO, HC and smoke emissions are low for biodiesel blends while BSFC and NOx emissions are slightly higher. Taking all results into account it can be clinched that B10 blend of Juliflora biodiesel has viable option for diesel engine applications.

Effect of Multiple Injection Strategy on Atomization and Emission Reduction Characteristics in a Diesel-Ethanol Fueled Engine

2010 ◽  
Author(s):  
Su Han Park ◽  
In Mo Youn ◽  
Sung Wook Park ◽  
Chang Sik Lee
Keyword(s):  
Diesel Engine ◽  
Exhaust Emissions ◽  
Common Rail ◽  
Biodiesel Fuel ◽  
Injection Timing ◽  
Multiple Injection ◽  
Spray Cone ◽  
Injection Interval ◽  
Injection Modes ◽  
Blended Fuels

The aim of this work is to investigate the effect of the multiple injections on the overall spray and the exhaust emissions characteristics in a common rail four cylinder diesel engine operated using diesel-ethanol blended fuels. In order to prevent the phase separation in blended fuels, biodiesel fuel that based on palm oil added to the blended fuels. The reduction problem of cetane number in blended fuels was supplemented by the addition of biodiesel fuel. The spray characteristics were analyzed through the spray images which obtained by the high speed camera. In addition, the combustion and exhaust emissions characteristics were measured and analyzed by using a four cylinder diesel engine with common rail injection system. It revealed that the increase of the injection interval induces the slow development rate of the second spray in the multiple injection modes. The spray cone angle of the single injection mode is wider than that of the multiple injection modes. The advance of the first injection timing caused the reduction of the second injection quantity, and the relaxation of the combustion pressure rise rate. NOx emission shows a reduction trend by the increased ethanol blending ratio, while it shows an increasing pattern by the advance of the first injection timing at the fixed second injection. In HC and CO emissions, the short injection interval between the first and the second injections is better than long injection interval.

Two-Stroke Marine Diesel Engine Variable Injection Timing System Performance Evaluation and Optimum Setting for Minimum Fuel Consumption at Acceptable NOx Levels

2014 ◽  
Author(s):  
Dimitrios T. Hountalas ◽  
Spiridon Raptotasios ◽  
Antonis Antonopoulos ◽  
Stavros Daniolos ◽  
Iosif Dolaptzis ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Engine Performance ◽  
Operating Conditions ◽  
Specific Fuel Consumption ◽  
Injection Timing ◽  
Nox Emissions ◽  
Pressure Measurements ◽  
Cylinder Pressure ◽  
Start Of Injection

Currently the most promising solution for marine propulsion is the two-stroke low-speed diesel engine. Start of Injection (SOI) is of significant importance for these engines due to its effect on firing pressure and specific fuel consumption. Therefore these engines are usually equipped with Variable Injection Timing (VIT) systems for variation of SOI with load. Proper operation of these systems is essential for both safe engine operation and performance since they are also used to control peak firing pressure. However, it is rather difficult to evaluate the operation of VIT system and determine the required rack settings for a specific SOI angle without using experimental techniques, which are extremely expensive and time consuming. For this reason in the present work it is examined the use of on-board monitoring and diagnosis techniques to overcome this difficulty. The application is conducted on a commercial vessel equipped with a two-stroke engine from which cylinder pressure measurements were acquired. From the processing of measurements acquired at various operating conditions it is determined the relation between VIT rack position and start of injection angle. This is used to evaluate the VIT system condition and determine the required settings to achieve the desired SOI angle. After VIT system tuning, new measurements were acquired from the processing of which results were derived for various operating parameters, i.e. brake power, specific fuel consumption, heat release rate, start of combustion etc. From the comparative evaluation of results before and after VIT adjustment it is revealed an improvement of specific fuel consumption while firing pressure remains within limits. It is thus revealed that the proposed method has the potential to overcome the disadvantages of purely experimental trial and error methods and that its use can result to fuel saving with minimum effort and time. To evaluate the corresponding effect on NOx emissions, as required by Marpol Annex-VI regulation a theoretical investigation is conducted using a multi-zone combustion model. Shop-test and NOx-file data are used to evaluate its ability to predict engine performance and NOx emissions before conducting the investigation. Moreover, the results derived from the on-board cylinder pressure measurements, after VIT system tuning, are used to evaluate the model’s ability to predict the effect of SOI variation on engine performance. Then the simulation model is applied to estimate the impact of SOI advance on NOx emissions. As revealed NOx emissions remain within limits despite the SOI variation (increase).

Performance and emission reduction characteristics of cerium oxide nanoparticle-water emulsion biofuel in diesel engine with modified coated piston

2019 ◽  
Vol 26 (26) ◽  
pp. 27362-27371 ◽  
Author(s):  
Elumalai Perumal Venkatesan ◽  
Annamalai Kandhasamy ◽  
Arularasu Sivalingam ◽  
Appuraja Senthil Kumar ◽  
KrishnaMoorthy Ramalingam ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Cerium Oxide ◽  
Emission Reduction ◽  
Water Emulsion ◽  
Performance And Emission ◽  
Oxide Nanoparticle ◽  
Reduction Characteristics

scholarly journals INVESTIGATION ON DIESEL ENGINE FUELLED BY MAHUA BIODIESEL

2021 ◽  
Vol 9 (1) ◽  
pp. 436-443
Author(s):  
M.Kannan, R.Balaji, R.T Sarath Babu, Chandrakant B. Shende, Ashish Selokar
Keyword(s):  
Diesel Engine ◽  
Engine Performance ◽  
Primary Objective ◽  
Injection Timing ◽  
Emission Characteristics ◽  
Oxides Of Nitrogen ◽  
Fuel Blend ◽  
Biodiesel Blends ◽  
Mahua Oil ◽  
Mahua Biodiesel

The primary objective of this study is to discover the effects of injection timing on performance, emission and combustion characteristics effect of advanced and retarded injection timing of the engine fuelled with mahua oil biodiesel blends. The engine performance, combustion and emission characteristics of the mahua oil biodiesel blends (B20, B40, B60, B80and B100) are investigated in this experimentation without any modification of the diesel engine. At this advanced pressure t he efficiency of engine by means of CO, Unburned HC gases and smoke emissions with higher oxides of nitrogen was observed compared to diesel. The obtained results are compared with a neat diesel and mahua oil biodiesel blends are shown through the graphs. From this study, identifies optimum fuel blend of this work. Thus, the combustion of duration is similar in all variance in pressure. This research paved a way to bio-diesel in mahua oil mixture and draws best outcome in emission less and to maintain eco-friendly environment.  

Spray and Combustion Characteristics of Biodiesel∕Diesel Blended Fuel in a Direct Injection Common-Rail Diesel Engine

2008 ◽  
Vol 130 (3) ◽  
Author(s):  
Hyun Kyu Suh ◽  
Hyun Gu Roh ◽  
Chang Sik Lee
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Direct Injection ◽  
Injection Rate ◽  
Combustion Characteristics ◽  
Biodiesel Fuel ◽  
Injection Timing ◽  
Pilot Injection ◽  
Blended Fuel ◽  
Conventional Diesel Fuel

The aim of this work is to investigate the effect of the blending ratio and pilot injection on the spray and combustion characteristics of biodiesel fuel and compare these factors with those of diesel fuel in a direct injection common-rail diesel engine. In order to study the factors influencing the spray and combustion characteristics of biodiesel fuel, experiments involving exhaust emissions and engine performance were conducted at various biodiesel blending ratios and injection conditions for engine operating conditions. The macroscopic and microscopic spray characteristics of biodiesel fuel, such as injection rate, split injection effect, spray tip penetration, droplet diameter, and axial velocity distribution, were compared with the results from conventional diesel fuel. For biodiesel blended fuel, it was revealed that a higher injection pressure is needed to achieve the same injection rate at a higher blending ratio. The spray tip penetration of biodiesel fuel was similar to that of diesel. The atomization characteristics of biodiesel show that it has higher Sauter mean diameter and lower spray velocity than conventional diesel fuel due to high viscosity and surface tension. The peak combustion pressures of diesel and blending fuel increased with advanced injection timing and the combustion pressure of biodiesel fuel is higher than that of diesel fuel. As the pilot injection timing is retarded to 15deg of BTDC that is closed by the top dead center, the dissimilarities of diesel and blending fuels combustion pressure are reduced. It was found that the pilot injection enhanced the deteriorated spray and combustion characteristics of biodiesel fuel caused by different physical properties of the fuel.

scholarly journals Modification of a Direct Injection Diesel Engine in Improving the Ignitability and Emissions of Diesel–Ethanol–Palm Oil Methyl Ester Blends

Energies ◽  
2019 ◽  
Vol 12 (14) ◽  
pp. 2644 ◽  
Author(s):  
Norhidayah Mat Taib ◽  
Mohd Radzi Abu Mansor ◽  
Wan Mohd Faizal Wan Mahmood
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Ambient Temperature ◽  
Palm Oil ◽  
Compression Ratio ◽  
Direct Injection ◽  
Cetane Number ◽  
Engine Performance ◽  
Injection Timing ◽  
Injection Strategies

Blending diesel with biofuels, such as ethanol and palm oil methyl ester (PME), enhances the fuel properties and produces improved engine performance and low emissions. However, the presence of ethanol, which has a small cetane number and low heating value, reduces the fuel ignitability. This work aimed to study the effect of injection strategies, compression ratio (CR), and air intake temperature (Ti) modification on blend ignitability, combustion characteristics, and emissions. Moreover, the best composition of diesel–ethanol–PME blends and engine modification was selected. A simulation was also conducted using Converge CFD software based on a single-cylinder direct injection compression ignition Yanmar TF90 engine parameter. Diesel–ethanol–PME blends that consist of 10% ethanol with 40% PME (D50E10B40), D50E25B25, and D50E40B10 were selected and conducted on different injection strategies, compression ratios, and intake temperatures. The results show that shortening the injection duration and increasing the injected mass has no significant effect on ignition. Meanwhile, advancing the injection timing improves the ignitability but with weak ignition energy. Therefore, increasing the compression ratio and ambient temperature helps ignite the non-combustible blends due to the high temperature and pressure. This modification allowed the mixture to ignite with a minimum CR of 20 and Ti of 350 K. Thus, blending high ethanol contents in a diesel engine can be applied by advancing the injection, increasing the CR, and increasing the ambient temperature. From the emission comparison, the most suitable mixtures that can be operated in the engine without modification is D50E25B25, and the most appropriate modification on the engine is by increasing the ambient temperature at 350 K.

scholarly journals Influence of Fuel Injection Pressure on the Emissions Characteristics and Engine Performance in a CRDI Diesel Engine Fueled with Palm Biodiesel Blends

Energies ◽  
2019 ◽  
Vol 12 (20) ◽  
pp. 3837 ◽  
Author(s):  
Sam Ki Yoon ◽  
Jun Cong Ge ◽  
Nag Jung Choi
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Fuel Injection ◽  
Injection Pressure ◽  
Biodiesel Fuel ◽  
Nox Emissions ◽  
Oxides Of Nitrogen ◽  
Fuel Blend ◽  
Engine Load ◽  
Fuel Injection Pressure

This experiment investigates the combustion and emissions characteristics of a common rail direct injection (CRDI) diesel engine using various blends of pure diesel fuel and palm biodiesel. Fuel injection pressures of 45 and 65 MPa were investigated under engine loads of 50 and 100 Nm. The fuels studied herein were pure diesel fuel 100 vol.% with 0 vol.% of palm biodiesel (PBD0), pure diesel fuel 80 vol.% blended with 20 vol.% of palm biodiesel (PBD20), and pure diesel fuel 50 vol.% blended with 50 vol.% of palm biodiesel (PBD50). As the fuel injection pressure increased from 45 to 65 MPa under all engine loads, the combustion pressure and heat release rate also increased. The indicated mean effective pressure (IMEP) increased with an increase of the fuel injection pressure. In addition, for 50 Nm of the engine load, an increase to the fuel injection pressure resulted in a reduction of the brake specific fuel consumption (BSFC) by an average of 2.43%. In comparison, for an engine load of 100 Nm, an increase in the fuel injection pressure decreased BSFC by an average of 0.8%. Hydrocarbon (HC) and particulate matter (PM) decreased as fuel pressure increased, independent of the engine load. Increasing fuel injection pressure for 50 Nm engine load using PBD0, PBD20 and PBD50 decreased carbon monoxide (CO) emissions. When the fuel injection pressure was increased from 45 MPa to 65 MPa, oxides of nitrogen (NOx) emissions were increased for both engine loads. For a given fuel injection pressure, NOx emissions increased slightly as the biodiesel content in the fuel blend increased.

An Experimental Study on Smoke Reduction Effect of Post Injection in Combination With Pilot Injection for a Diesel Engine

2013 ◽  
Vol 136 (4) ◽  
Author(s):  
Long Liu ◽  
Naoto Horibe ◽  
Tatsuya Komizo ◽  
Issei Tamura ◽  
Takuji Ishiyama
Keyword(s):  
Diesel Engine ◽  
Injection Pressure ◽  
Injection Timing ◽  
Nox Emissions ◽  
Pilot Injection ◽  
Post Injection ◽  
Spray Flames ◽  
Injection Quantity ◽  
Main Injection ◽  
Reduction Effect

With the universal utilization of the common-rail injection system in automotive diesel engines, the multistage injection strategies have become typical approaches to satisfy the increasingly stringent emission regulations, and especially the post injection has received considerable attention as an effective way for reducing the smoke emissions. Normally the post injection is applied in combination with the pilot injection to restrain the NOx emissions, smoke emissions, and combustion noise simultaneously, and the pilot injection condition affects the combustion process of the main injection and might affect the smoke reduction effect of the post injection. Thus this study aims at obtaining the post injection strategy to reduce smoke emissions in a diesel engine, where post injection is employed in combination with pilot injection. The experiments were performed using a single-cylinder diesel engine under various conditions of pilot and post injection with a constant load at an IMEP of 1.01 MPa, fixed speed of 1500 rpm, and NOx emissions concentration of 150 ± 5 ppm that was maintained by adjusting the EGR ratio. The injection pressure was set at 90 MPa at first, and then it was varied to 125 MPa to evaluate the effects of post injection on the smoke reduction in the case of higher injection pressure. The experimental results show that small post injection quantity with a short interval from the end of main injection causes less smoke emissions. And larger pilot injection quantity and later pilot injection timing lead to higher smoke emissions. And then, to explore and interpret the smoke emissions tendencies with varying pilot and post injection conditions, the experimental results of three-stage injection conditions were compared to those of two reference cases, which only included the pilot and main injection, and the interaction between main spray flames and post sprays was applied for analysis. Based on the comparative analysis, the larger smoke reduction effect of post injection was observed with the larger pilot injection quantity, while it is not greatly influenced by pilot injection timing. In addition, the smoke emissions can be reduced considerably by increasing the injection pressure, however the smoke reduction effect of post injection was attenuated. And all of these tendencies were able to be interpreted by considering the intensity variation of the interaction between main spray flames and post sprays.

Sign in / Sign up

Export Citation Format

Share Document