scholarly journals Proposal of a Novel Semi-Submersible Floating Wind Turbine Platform Composed of Inclined Columns and Multi-Segmented Mooring Lines

Energies ◽  
2019 ◽  
Vol 12 (9) ◽  
pp. 1809 ◽  
Author(s):  
Zhenqing Liu ◽  
Qingsong Zhou ◽  
Yuangang Tu ◽  
Wei Wang ◽  
Xugang Hua
Keyword(s):  
Wind Turbine ◽  
Offshore Wind ◽  
Mooring Line ◽  
Offshore Wind Turbine ◽  
Analysis Tool ◽  
Mooring Lines ◽  
Offshore Area ◽  
Floating Wind Turbine ◽  
Inclined Angle ◽  
Heave Motion

The semi-submersible floating offshore wind turbine has been studied in detail due to its good stability. However, the occurrence of typhoons are very frequent in China’s offshore area, putting forward a higher requirement for the stability of the floating wind turbine system. By changing the connection mode of the mooring line as well as the structural form of the platform based on the original OC4 model, two groups of models were examined by an in-house developed code named as the Analysis Tool of Floating Wind Turbine (AFWT). The influence of the arrangement of the mooring lines and the inclination angle of the upper columns on the motion response were clarified. It was found that the surge motion of the platform would be obviously decreased by decreasing the length of the upper segments of the mooring lines, while the heave motion of the platform would be significantly decreased as increasing the inclined angle of the columns. Therefore, a new model integrating the optimized multi-segmented mooring lines and the optimized inclined columns was proposed. The examinations showed that compared with the response motions of the original OC4 semi-submersible model, the proposed model could reduce both the surge and heave motions of the platform effectively.

scholarly journals Mooring Line Damping Estimation for a Floating Wind Turbine

2014 ◽  
Vol 2014 ◽  
pp. 1-10 ◽  
Author(s):  
Dongsheng Qiao ◽  
Jinping Ou
Keyword(s):  
Wind Turbine ◽  
Estimation Method ◽  
Excitation Amplitude ◽  
Dynamic Responses ◽  
Offshore Wind ◽  
Scale Model ◽  
Mooring Line ◽  
Offshore Wind Turbine ◽  
Floating Wind Turbine ◽  
Excitation Period

The dynamic responses of mooring line serve important functions in the station keeping of a floating wind turbine (FWT). Mooring line damping significantly influences the global motions of a FWT. This study investigates the estimation of mooring line damping on the basis of the National Renewable Energy Laboratory 5 MW offshore wind turbine model that is mounted on the ITI Energy barge. A numerical estimation method is derived from the energy absorption of a mooring line resulting from FWT motion. The method is validated by performing a 1/80 scale model test. Different parameter changes are analyzed for mooring line damping induced by horizontal and vertical motions. These parameters include excitation amplitude, excitation period, and drag coefficient. Results suggest that mooring line damping must be carefully considered in the FWT design.

Parametric Study of Catenary Mooring System for a Semisubmersible Floating Wind Turbine in Intermediate Water Depth

2020 ◽  
Author(s):  
Jiawen Li ◽  
Qiang Zhang ◽  
Jiali Du ◽  
Yichen Jiang
Keyword(s):  
Wind Turbine ◽  
Water Depth ◽  
Offshore Wind ◽  
Design Parameters ◽  
Mooring Line ◽  
Offshore Wind Turbine ◽  
Reference Structure ◽  
Intermediate Water ◽  
Mooring System ◽  
Floating Wind Turbine

Abstract This paper presents a parametric design study of the mooring system for a floating offshore wind turbine. We selected the OC4 DeepCwind semisubmersible floating wind turbine as the reference structure. The design water depth was 50 m, which was the transition area between the shallow and deep waters. For the floating wind turbine working in this water area, the restoring forces and moments provided by the mooring lines were significantly affected by the heave motion amplitude of the platform. Thus, the mooring design for the wind turbine in this working depth was different from the deep-water catenary mooring system. In this study, the chosen design parameters were declination angle, fairlead position, mooring line length, environmental load direction, and mooring line number. We conducted fully coupled aero-hydro dynamic simulations of the floating wind turbine system in the time domain to investigate the influences of different mooring configurations on the platform motion and the mooring tension. We evaluated both survival and accidental conditions to analyze the mooring safety under typhoon and mooring fail conditions. On the basis of the simulation results, this study made several design recommendations for the mooring configuration for floating wind turbines in intermediate water depth applied in China.

scholarly journals Study of Floating Wind Turbine with Modified Tension Leg Platform Placed in Regular Waves

Energies ◽  
2019 ◽  
Vol 12 (4) ◽  
pp. 703 ◽  
Author(s):  
Juhun Song ◽  
Hee-Chang Lim
Keyword(s):  
Wind Turbine ◽  
Real Data ◽  
Offshore Wind ◽  
Scale Model ◽  
Offshore Wind Turbine ◽  
Wave Loads ◽  
Tension Leg Platform ◽  
Mooring Lines ◽  
Floating Wind Turbine ◽  
Wave Conditions

In this study, the typical ocean environment was simulated with the aim to investigate the dynamic response under various environmental conditions of a Tension Leg Platform (TLP) type floating offshore wind turbine system. By applying Froude scaling, a scale model with a scale of 1:200 was designed and model experiments were carried out in a lab-scale wave flume that generated regular periodic waves by means of a piston-type wave generator while a wave absorber dissipated wave energy on the other side of the channel. The model was designed and manufactured based on the standard prototype of the National Renewable Energy Laboratory (NREL) 5 MW offshore wind turbine. In the first half of the study, the motion and structural responses for operational wave conditions of the North Sea near Scotland were considered to investigate the performance of a traditional TLP floating wind turbine compared with that of a newly designed TLP with added mooring lines. The new mooring lines were attached with the objective of increasing the horizontal stiffness of the system and thereby reducing the dominant motion of the TLP platform (i.e., the surge motion). The results of surge translational motions were obtained both in the frequency domain, using the response amplitude operator (RAO), and in the time domain, using the omega arithmetic method for the relative velocity. The results obtained show that our suggested concept improves the stability of the platform and reduces the overall motion of the system in all degrees-of-freedom. Moreover, the modified design was verified to enable operation in extreme wave conditions based on real data for a 100-year return period of the Northern Sea of California. The loads applied by the waves on the structure were also measured experimentally using modified Morison equation—the formula most frequently used to estimate wave-induced forces on offshore floating structures. The corresponding results obtained show that the wave loads applied on the new design TLP had less amplitude than the initial model and confirmed the significant contribution of the mooring lines in improving the performance of the system.

VolturnUS 1:8: Conclusion of 18-Months of Operation of the First Grid-Connected Floating Wind Turbine Prototype in the Americas

2015 ◽  
Author(s):  
Anthony M. Viselli ◽  
Andrew J. Goupee ◽  
Habib J. Dagher ◽  
Christopher K. Allen
Keyword(s):  
Wind Turbine ◽  
Large Data ◽  
Full Scale ◽  
Offshore Wind ◽  
Mooring Line ◽  
Offshore Wind Turbine ◽  
Data Set ◽  
Floating Offshore Wind Turbine ◽  
The Past ◽  
Floating Wind Turbine

This paper presents an overview of the successful conclusion of 18 months of testing the first grid-connected floating offshore wind turbine prototype in the Americas. The prototype, called VolturnUS 1:8, was installed off Castine, Maine, USA. The prototype is a 1:8 scale prototype and serves to de-risk the deployment of a full-scale 6MW turbine. VolturnUS utilizes innovations in materials, construction, and deployment technologies such as a concrete semi-submersible hull and an advanced composite tower to reduce the costs of offshore wind. The prototype unit was designed following the American Bureau of Shipping (ABS) “Guide for Building and Classing Floating Offshore Wind Turbine Installations”. Froude scaling was used in designing the 1:8-scale VolturnUS prototype so that the motions of the prototype in the relatively protected site represent those of the full-scale unit in an open site farther offshore. During the past year, a comprehensive instrumentation package monitored key performance characteristics of the platform during operational, extreme, and survival storm conditions. Data collected include: wind speed, turbine power, rotor angular frequency, blade pitch, torque, acceleration; tower bending moment, 6 DOF accelerations at tower top and base, mooring line tensions, and wave elevation at the platform. During the past year the prototype has experienced many environments representative of scaled ABS design conditions including operational wind and sea-states, 50-year sea states and 500-year survival sea states. This large data set provides a unique view of a near full-scale floating wind turbine subjected to its prescribed environmental conditions. Inspections of the concrete hull following removal provided confirmation of material durability. Marine growth measurements provide data for future design efforts.

scholarly journals Numerical Analysis of a Catenary Mooring System Attached by Clump Masses for Improving the Wave-Resistance Ability of a Spar Buoy-Type Floating Offshore Wind Turbine

2019 ◽  
Vol 9 (6) ◽  
pp. 1075 ◽  
Author(s):  
Zhenqing Liu ◽  
Yuangang Tu ◽  
Wei Wang ◽  
Guowei Qian
Keyword(s):  
Wind Turbine ◽  
International Energy Agency ◽  
Wave Resistance ◽  
Offshore Wind ◽  
Irregular Waves ◽  
Mooring Line ◽  
Offshore Wind Turbine ◽  
Induced Response ◽  
Mooring Lines ◽  
Energy Agency

The International Energy Agency (IEA), under the auspices of their Offshore Code Comparison Collaboration (OC3) initiative, has completed high-level design OC-3 Hywind system. In this system the wind turbine is supported by a spar buoy platform, showing good wave-resistance performance. However, there are still large values in the motion of surge degree of freedom (DOF). Addition of clump masses on the mooring lines is an effective way of reducing the surge motion. However, the optimization of the locations where the clump masses are added is still not clear. In this study, therefore, an in-house developed code is verified by comparing the results of the original OC3 model with those by FAST. The improvement of the performance of this modified platform as a function of the location of the clump masses has been examined under three regular waves and three irregular waves. In the findings of these examination, it was apparent that attaching clump masses with only one-tenth of the mass of the total mooring-line effectively reduces the wave-induced response. Moreover, there is an obvious improvement as the depth of the location where the clump masses mounted is increased.

scholarly journals Alternative Mooring Systems for a Very Large Offshore Wind Turbine Supported by a Semisubmersible Floating Platform

2018 ◽  
Vol 140 (5) ◽  
Author(s):  
Jinsong Liu ◽  
Lance Manuel
Keyword(s):  
Wind Turbine ◽  
Integrated System ◽  
Offshore Wind ◽  
Mooring Line ◽  
Offshore Wind Turbine ◽  
System Response ◽  
Mooring System ◽  
Floating Platform ◽  
Mooring Lines ◽  
Wind Speeds

As offshore wind turbines supported on floating platforms extend to deep waters, the various effects involved in the dynamics, especially those resulting from the influence of moorings, become significant when predicting the overall integrated system response. The combined influence of waves and wind affect motions of the structure and induce tensile forces in mooring lines. The investigation of the system response under misaligned wind-wave conditions and the selection of appropriate mooring systems to minimize the turbine, tower, and mooring system loads is the subject of this study. We estimate the 50-year return response of a semisubmersible platform supporting a 13.2 MW wind turbine as well as mooring line forces when the system is exposed to four different wave headings with various environmental conditions (wind speeds and wave heights). Three different mooring system patterns are presented that include 3 or 6 mooring lines with different interline angles. Performance comparisons of the integrated systems may be used to define an optimal system for the selected large wind turbine.

scholarly journals Dynamic Response for a Submerged Floating Offshore Wind Turbine with Different Mooring Configurations

2019 ◽  
Vol 7 (4) ◽  
pp. 115 ◽  
Author(s):  
Yane Li ◽  
Conghuan Le ◽  
Hongyan Ding ◽  
Puyang Zhang ◽  
Jian Zhang
Keyword(s):  
Dynamic Response ◽  
Wind Turbine ◽  
Dynamic Responses ◽  
Offshore Wind ◽  
Mooring Line ◽  
Offshore Wind Turbine ◽  
Intermediate Water ◽  
Mooring System ◽  
Mooring Lines ◽  
Floating Offshore Wind Turbine

The paper discusses the effects of mooring configurations on the dynamic response of a submerged floating offshore wind turbine (SFOWT) for intermediate water depths. A coupled dynamic model of a wind turbine-tower-floating platform-mooring system is established, and the dynamic response of the platform, tensions in mooring lines, and bending moment at the tower base and blade root under four different mooring configurations are checked. A well-stabilized configuration (i.e., four vertical lines and 12 diagonal lines with an inclination angle of 30°) is selected to study the coupled dynamic responses of SFOWT with broken mooring lines, and in order to keep the safety of SFOWT under extreme sea-states, the pretension of the vertical mooring line has to increase from 1800–2780 kN. Results show that the optimized mooring system can provide larger restoring force, and the SFOWT has a smaller movement response under extreme sea-states; when the mooring lines in the upwind wave direction are broken, an increased motion response of the platform will be caused. However, there is no slack in the remaining mooring lines, and the SFOWT still has enough stability.

Design of Mooring Lines of Floating Offshore Wind Turbine in Jeju Offshore Area

2014 ◽  
Author(s):  
Hyungjun Kim ◽  
Joonmo Choung ◽  
Gi-Young Jeon
Keyword(s):  
Wind Turbine ◽  
Limit State ◽  
Design Procedure ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Ultimate Limit State ◽  
Mooring Lines ◽  
Offshore Area ◽  
Floating Offshore Wind Turbine ◽  
Wind Turbine System

This paper presents a mooring design procedure of a floating offshore wind turbine. The offshore environment data of Jeju south sea collected from Korea Hydrographic and Oceanographic Administration (KHOA) are used as environmental conditions for hydrodynamic analysis. A semi-submersible floating wind turbine system is considered based on Offshore Code Comparison Collaborative Continuation (OC4) DeepCWind platform and the National Renewable Energy Laboratory (NREL) 5MW class wind turbine. Catenary mooring with studless chain is chosen as the mooring system. Important design decisions such as how large the nominal sizes are, how long the mooring lines are, how far the anchor points are located, are demonstrated in detail. Considering ultimate limit state and fatigue limit state based on 100-year return period and 50 year design life, respectively, long-term predictions of breaking strength and fatigue are performed.

The Influence of the Mooring System on the Motions and Stability of a Semi-Submersible Floating Wind Turbine

2015 ◽  
Author(s):  
Fons Huijs
Keyword(s):  
Wind Turbine ◽  
Low Frequency ◽  
Considerable Effect ◽  
Offshore Wind ◽  
Mooring Line ◽  
Offshore Wind Turbine ◽  
Mooring System ◽  
Mooring Lines ◽  
System A ◽  
Turbine Design

One of the main aspects of a floating offshore wind turbine design is its mooring system, which can strongly influence the floater stability and motions. This is illustrated by considering two catenary mooring systems for the same semi-submersible. The main difference between the two systems is the position of the connection points of the mooring lines on the floater, the so-called fairleads. The philosophy is that the design can be improved by shifting the fairleads to the highest feasible level. For both mooring systems, the floater motions and stability are assessed. Stability curves are derived, taking both the effect of hydrostatics and the mooring system into account. Floater motions are analyzed using both uncoupled frequency domain calculations and coupled aero-hydro-servo-elastic time domain simulations. The mooring system is found to have a considerable effect on the floating stability. The effect on the motions is less profound for the considered mooring systems and limited to the low frequency range. Mooring line tensions are however significantly affected by the fairlead position. It is concluded that, with a well-designed mooring system, a smaller and thus less expensive floater can be used while still meeting the requirements in terms of stability and maximum motions. In addition, the mooring lines may be lighter as well.

Sign in / Sign up

Export Citation Format

Share Document