scholarly journals Energy Performance Comparison between Liquid-Desiccant-Assisted Air Conditioning System and Dedicated Outdoor Air System in Different Climatic Regions

Energies ◽  
2019 ◽  
Vol 12 (9) ◽  
pp. 1798
Author(s):  
Su Liu ◽  
Sang-Tae No ◽  
Jae-Weon Jeong
Keyword(s):  
Energy Consumption ◽  
Air Conditioning ◽  
Building Design ◽  
Energy Performance ◽  
Parallel System ◽  
Office Buildings ◽  
Outdoor Air ◽  
Liquid Desiccant ◽  
Climatic Regions ◽  
Air System

The main purpose of this research is to analyze and compare the energy performance of two different novel air conditioning systems; one is a dedicated outdoor air system (DOAS) with a parallel system and the other is a heat-pump-integrated liquid-desiccant and evaporative-cooling-assisted 100% outdoor air system (HPLD-IDECOAS). It was assumed that office buildings served by each system were located in six cities representing four different climatic regions in China. The hourly thermal loads of the office buildings meeting the local building design codes of each selected city were predicted by the TRNSYS 18 software package. The hourly thermal load data were imported into the commercial engineering equation solver (EES) program to estimate the operating energy consumption of each system via detailed energy simulations performed using valid system simulation models. The results show that the HPLD-IDECOAS has higher energy-saving potential than the DOAS with a parallel system in climate regions with high humidity, whereas, in dry regions, the difference in energy consumption between the two systems was not significant.

scholarly journals Energy Performance Comparison between Two Liquid Desiccant and Evaporative Cooling-Assisted Air Conditioning Systems

Energies ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 522
Author(s):  
Su Liu ◽  
Jae-Weon Jeong
Keyword(s):  
Energy Consumption ◽  
Air Conditioning ◽  
Evaporative Cooling ◽  
Dew Point ◽  
Outdoor Air ◽  
Liquid Desiccant ◽  
Energy Saving Potential ◽  
Evaporative Cooler ◽  
Air Conditioning Systems ◽  
Direct Evaporative Cooler

This study investigated the annual energy saving potential and system performance of two different evaporative cooling-based liquid desiccant and evaporative cooling-assisted air conditioning systems. One system used an indirect and direct evaporative cooler with a two-stage package to match the target supply air point. The other was equipped with a single-stage, packaged dew-point evaporative cooler that used a portion of the process air, which had been dehumidified in advance. Systems installed with the two evaporative coolers were compared to determine which one was more energy efficient and which one could provide better thermal comfort for building occupants in a given climate zone, using detailed simulation data. The detailed energy consumption data of these two systems were estimated using an engineering equation solver with each component model. The results showed that the liquid desiccant and dew-point evaporative-cooler-assisted 100% outdoor air system (LDEOAS) resulted in approximately 34% more annual primary energy consumption than that of the liquid desiccant and the indirect and direct evaporative-cooler-assisted 100% outdoor air system (LDIDECOAS). However, the LDEOAS could provide drier and cooler supply air, compared with the LDIDECOAS. In conclusion, LDIDECOAS has a higher energy saving potential than LDEOAS, with an acceptable level of thermal comfort.

Energy Saving Potentials of All Cold Air Distribution System With Stratified Air Conditioning in Large Space Building

2008 ◽  
Author(s):  
Wei Bing ◽  
Li Li ◽  
Yuefen Gao ◽  
Xianliang Yang
Keyword(s):  
Energy Consumption ◽  
Energy Saving ◽  
Air Conditioning ◽  
Distribution Systems ◽  
Future Application ◽  
Air Distribution ◽  
Outdoor Air ◽  
Large Space ◽  
Cold Air ◽  
Air System

So far the energy saving potentials in refrigeration and air conditioning systems are the focuses of researchers all over the world. The all cold air distribution systems are being widely used due to the advantages of saving building space, less energy consumption in some given conditions and less initial cost, mostly in the residential or office buildings. The stratified air conditioning technology is adopted mainly for large space buildings to reduce the system energy consumption, normally at conventional supply air temperature. In this paper, with an example of large space building, the energy consumptions of four all outdoor air systems are calculated and compared from the view of the total annual primary energy consumption. The detailed analysis shows that comparing the conventional all outdoor air system for the whole indoor space or that with stratified air conditioning technology, the all cold outdoor air system with stratified air conditioning has the energy saving potentials. It will be promoted in the future application of HVAC systems in large space buildings.

Impacts of Air Conditioning Equipment Sizing on Energy Performance of US Office Buildings

2021 ◽  
pp. 1-24
Author(s):  
Franklin Chiu ◽  
Moncef Krarti
Keyword(s):  
Energy Consumption ◽  
Air Conditioning ◽  
Energy Performance ◽  
Office Buildings ◽  
Peak Demand ◽  
Capital Costs ◽  
Wide Range ◽  
Ac Systems ◽  
Equipment Sizing ◽  
Conditioning Equipment

Abstract The paper summarizes the results of a systematic and comprehensive analysis to investigate the impacts of inadequate sizing air conditioning (AC) systems on the overall energy consumption of medium and large office buildings located in representative US cities. The effects of proper sizing on the overall and disaggregated AC systems are evaluated in terms of energy consumption, peak demand, equipment run-time, and indoor thermal comfort. The presented analysis covers the performance a wide range of AC equipment components that serve US office buildings including packaged rooftop units as well as central cooling plants. The analysis results indicate that oversizing penalties can be significant on the annual energy consumption and electrical peak demand as well as capital costs for both medium and large office buildings. In particular, the reliance on simplified calculation methods and rules-of-thumb to determine equipment capacities can lead to significantly oversizing AC systems for office buildings in the vast majority of US climates and can result in increases of annual energy consumption and electrical peak demand of up to 29%. Moreover, oversizing increases capital costs required for air conditioning office buildings and extends cycling periods and associated structural stresses and failures of AC equipment.

Comparison study of air mixing modes in liquid desiccant based all-air air conditioning systems

2011 ◽  
Vol 33 (4) ◽  
pp. 423-435 ◽  
Author(s):  
Fu Xiao ◽  
XiaoFeng Niu
Keyword(s):  
Energy Consumption ◽  
Air Conditioning ◽  
Coefficient Of Performance ◽  
Liquid Desiccant ◽  
Total Energy Consumption ◽  
Air Conditioning System ◽  
Operation Conditions ◽  
Air System ◽  
Air Mixing ◽  
Air Conditioning Systems

Liquid desiccant is an energy-saving, environmentally friendly and healthy means of air dehumidification. A liquid desiccant-based all-air air conditioning system is studied by simulation. Two different modes of air mixing between the return air and the fresh air are compared, that is mixing before and mixing after the liquid desiccant dehumidifier, respectively. System performance and total energy consumption of the two modes under different operation conditions are obtained. The results show that mixing air after dehumidification consumes less energy than mixing air before dehumidification. Coefficient of performance (COP) of the all-air system with air mixing after dehumidification is higher. The differences of COP and energy consumption between the two air mixing modes increase when the outdoor air temperature and relative humidity increase. Practical application: Liquid desiccant based all-air system is quite suitable for museums, libraries and computer centres where water is not allowed to enter the space for property safety and strict thermal-hygrometric control is necessary. The results of this paper provide guidelines on the selection of air mixing modes in liquid desiccant-based all-air systems, considering energy consumption and system COP.

scholarly journals A Fundamental Study on the Development of New Energy Performance Index in Office Buildings

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2064
Author(s):  
Jin-Hee Kim ◽  
Seong-Koo Son ◽  
Gyeong-Seok Choi ◽  
Young-Tag Kim ◽  
Sung-Bum Kim ◽  
...  
Keyword(s):  
Energy Consumption ◽  
Energy Requirement ◽  
Energy Performance ◽  
Office Buildings ◽  
Light Transmittance ◽  
Wall Structure ◽  
Fundamental Study ◽  
Future Studies ◽  
U Value ◽  
The Impact

Recently, there have been significant concerns regarding excessive energy use in office buildings with a large window-to-wall ratio (WWR) because of the curtain wall structure. However, prior research has confirmed that the impact of the window area on energy consumption varies depending on building size. A newly proposed window-to-floor ratio (WFR) correlates better with energy consumption in the building. In this paper, we derived the correlation by analyzing a simulation using EnergyPlus, and the results are as follows. In the case of small buildings, the results of this study showed that the WWR and energy requirement increase proportionally, and the smaller the size is, the higher the energy sensitivity will be. However, results also confirmed that this correlation was not established for buildings approximately 3600 m2 or larger. Nevertheless, from analyzing the correlation between the WFR and the energy requirements, it could be deduced that energy required increased proportionally when the WFR was 0.1 or higher. On the other hand, the correlation between WWR, U-value, solar heat gain coefficient (SHGC), and material property values of windows had little effect on energy when the WWR was 20%, and the highest effect was seen at a WWR of 100%. Further, with an SHGC below 0.3, the energy requirement decreased with an increasing WWR, regardless of U-value. In addition, we confirmed the need for in-depth research on the impact of the windows’ U-value, SHGC, and WWR, and this will be verified through future studies. In future studies on window performance, U-value, SHGC, visible light transmittance (VLT), wall U-value as sensitivity variables, and correlation between WFR and building size will be examined.

scholarly journals Modeling Energy Efficiency Performance and Cost-Benefit Analysis Achieving Net-Zero Energy Building Design: Case Studies of Three Representative Offices in Thailand

2021 ◽  
Vol 13 (9) ◽  
pp. 5201
Author(s):  
Kittisak Lohwanitchai ◽  
Daranee Jareemit
Keyword(s):  
High Efficiency ◽  
Energy Gap ◽  
Cost Benefit ◽  
Building Design ◽  
Energy Performance ◽  
Office Buildings ◽  
Zero Energy ◽  
Zero Energy Building ◽  
Investment Cost ◽  
High Investment

The concept of a zero energy building is a significant sustainable strategy to reduce greenhouse gas emissions. The challenges of zero energy building (ZEB) achievement in Thailand are that the design approach to reach ZEB in office buildings is unclear and inconsistent. In addition, its implementation requires a relatively high investment cost. This study proposes a guideline for cost-optimal design to achieve the ZEB for three representative six-story office buildings in hot and humid Thailand. The energy simulations of envelope designs incorporating high-efficiency systems are carried out using eQuest and daylighting simulation using DIALux evo. The final energy consumptions meet the national ZEB target but are higher than the rooftop PV generation. To reduce such an energy gap, the ratios of building height to width are proposed. The cost-benefit of investment in ZEB projects provides IRRs ranging from 10.73 to 13.85%, with payback periods of 7.2 to 8.5 years. The energy savings from the proposed designs account for 79.2 to 81.6% of the on-site energy use. The investment of high-performance glazed-windows in the small office buildings is unprofitable (NPVs = −14.77–−46.01). These research results could help architects and engineers identify the influential parameters and significant considerations for the ZEB design. Strategies and technical support to improve energy performance in large and mid-rise buildings towards ZEB goals associated with the high investment cost need future investigations.

scholarly journals Impact of Window to Wall Ratio on Energy Loads in Hot Regions: A Study of Building Energy Performance

Energies ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 1080
Author(s):  
Mamdooh Alwetaishi ◽  
Omrane Benjeddou
Keyword(s):  
Saudi Arabia ◽  
Building Materials ◽  
Building Design ◽  
Building Energy ◽  
Energy Performance ◽  
Design Stage ◽  
Design Solution ◽  
Building Energy Efficiency ◽  
Climatic Regions ◽  
Heating And Cooling

The concern regarding local responsive building design has gained more attention globally as of late. This is due to the issue of the rapid increase in energy consumption in buildings for the purpose of heating and cooling. This has become a crucial issue in educational buildings and especially in schools. The major issue in school buildings in Saudi Arabia is that they are a form of prototype school building design (PSBD). As a result, if there is any concern in the design stage and in relation to the selection of building materials, this will spread throughout the region. In addition to that, the design is repeated regardless of the climate variation within the kingdom of Saudi Arabia. This research will focus on the influence of the window to wall ratio on the energy load in various orientations and different climatic regions. The research will use the energy computer tool TAS Environmental Design Solution Limited (EDSL) to calculate the energy load as well as solar gain. During the visit to the sample schools, a globe thermometer will be used to monitor the globe temperature in the classrooms. This research introduces a framework to assist architects and engineers in selecting the proper window to wall ratio (WWR) in each direction within the same building based on adequate natural light with a minimum reliance on energy load. For ultimate WWR for energy performance and daylight, the WWR should range from 20% to 30%, depending on orientation, in order to provide the optimal daylight factor combined with building energy efficiency. This ratio can be slightly greater in higher altitude locations.

Development of a numerical approach to assess the effect of coupled heat and moisture transfer on energy consumption of residential buildings in Moroccan context

2021 ◽  
pp. 174425912110560
Author(s):  
Yassine Chbani Idrissi ◽  
Rafik Belarbi ◽  
Mohammed Yacine Ferroukhi ◽  
M’barek Feddaoui ◽  
Driss Agliz
Keyword(s):  
Energy Consumption ◽  
Building Materials ◽  
Moisture Transfer ◽  
Residential Buildings ◽  
Building Design ◽  
Energy Performance ◽  
Climatic Conditions ◽  
Heat And Moisture Transfer ◽  
Coupled Heat And Moisture ◽  
Heat And Moisture

Hygrothermal properties of building materials, climatic conditions and energy performance are interrelated and have to be considered simultaneously as part of an optimised building design. In this paper, a new approach to evaluate the energy consumption of residential buildings in Morocco is presented. This approach is based on the effect of coupled heat and moisture transfer in typical residential buildings and on their responses to the varied climatic conditions encountered in the country. This approach allows us to evaluate with better accuracy the response of building energy performance and the indoor comfort of building occupants. Annual energy consumption, cooling and heating energy requirements were estimated considering the six climatic zones of Morocco. Based on the results, terms related to coupled heat and moisture transfer can effectively correct the existing energy consumption calculations of the six zones of Morocco, which currently do not consider energy consumption due to coupled heat and moisture transfer.

Sign in / Sign up

Export Citation Format

Share Document