scholarly journals Experimental Study of DI Diesel Engine Operational and Environmental Behavior Using Blends of City Diesel with Glycol Ethers and RME

Energies ◽  
2019 ◽  
Vol 12 (8) ◽  
pp. 1547 ◽  
Author(s):  
Theodoros C. Zannis ◽  
Roussos G. Papagiannakis ◽  
Efthimios G. Pariotis ◽  
Marios I. Kourampas
Keyword(s):  
Diesel Engine ◽  
Oxygen Content ◽  
Direct Injection ◽  
Engine Performance ◽  
Injection Pressure ◽  
Cylinder Pressure ◽  
Performance Parameters ◽  
Glycol Ethers ◽  
Pressure Injection ◽  
Di Diesel Engine

An experimental investigation is performed in a single-cylinder direct-injection (DI) diesel engine using city diesel oil called DI1 and two blends of DI1 with a mixture of glycol ethers. The addition of glycol ethers to fuel DI1 produced oxygenated fuels GLY10 (10.2 mass-% glycol ethers) and GLY30 (31.3 mass-% glycol ethers) with 3% and 9% oxygen content, respectively. The addition of biofuel rapeseed methyl ester (RME) to fuel DI1 produced oxygenated blend RME30 (31.2 mass-% RME) with 3% oxygen content. Engine tests were performed with the four fuels in the DI diesel engine at 2500 RPM and at 20%, 40%, 60%, and 80% of full load. The experimental diesel engine was equipped with devices for recording cylinder pressure, injection pressure, and top dead center (TDC) position and also it was equipped with exhaust gas analyzers for measuring soot, NO, CO, and HC emissions. A MATLAB 2014 code was developed for analyzing recorded cylinder pressure, injection pressure, and TDC position data for all obtained engine cycles and for calculating the main engine performance parameters. The assessment of the experimental results showed that glycol ethers have more beneficial impact on soot and NO emissions compared to RME, whereas RME have less detrimental impact on engine performance parameters compared to glycol ethers.

scholarly journals THE EFFECT OF DIESEL-BIODIESEL BLENDS ON THE PERFORMANCE AND EXHAUST EMISSIONS OF A DIRECT INJECTION OFF-ROAD DIESEL ENGINE

Transport ◽  
2014 ◽  
Vol 29 (4) ◽  
pp. 440-448 ◽  
Author(s):  
Tomas Mickevičius ◽  
Stasys Slavinskas ◽  
Slawomir Wierzbicki ◽  
Kamil Duda
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Direct Injection ◽  
Engine Performance ◽  
Exhaust Emissions ◽  
Bench Test ◽  
Maximum Pressure ◽  
Cylinder Pressure ◽  
Biodiesel Blends ◽  
Performance And Emission

This paper presents a comparative analysis of the diesel engine performance and emission characteristics, when operating on diesel fuel and various diesel-biodiesel (B10, B20, B40, B60) blends, at various loads and engine speeds. The experimental tests were performed on a four-stroke, four-cylinder, direct injection, naturally aspirated, 60 kW diesel engine D-243. The in-cylinder pressure data was analysed to determine the ignition delay, the Heat Release Rate (HRR), maximum in-cylinder pressure and maximum pressure gradients. The influence of diesel-biodiesel blends on the Brake Specific Fuel Consumption (bsfc) and exhaust emissions was also investigated. The bench test results showed that when the engine running on blends B60 at full engine load and rated speed, the autoignition delay was 13.5% longer, in comparison with mineral diesel. Maximum cylinder pressure decreased about 1–2% when the amount of Rapeseed Methyl Ester (RME) expanded in the diesel fuel when operating at full load and 1400 min–1 speed. At rated mode, the minimum bsfc increased, when operating on biofuel blends compared to mineral diesel. The maximum brake thermal efficiency sustained at the levels from 0.3% to 6.5% lower in comparison with mineral diesel operating at full (100%) load. When the engine was running at maximum torque mode using diesel – RME fuel blends B10, B20, B40 and B60 the total emissions of nitrogen oxides decreased. At full and moderate load, the emission of carbon monoxide significantly raised as the amount of RME in fuel increased.

scholarly journals Performance Analysis of Direct Injection Diesel Engine Fueled with Diesel-Tomato Seed Oil Biodiesel Blending by ANOVA and ANN

Energies ◽  
2019 ◽  
Vol 12 (23) ◽  
pp. 4421 ◽  
Author(s):  
Karami ◽  
Rasul ◽  
Khan ◽  
Anwar
Keyword(s):  
Diesel Engine ◽  
Performance Analysis ◽  
Direct Injection ◽  
Engine Performance ◽  
Gas Temperature ◽  
Ann Model ◽  
Tomato Seed ◽  
Significance Level ◽  
Di Diesel Engine ◽  
Biodiesel Fuels

Biodiesel is an alternative fuel for diesel engine. Considering the differences between diesel and biodiesel fuels, the engine condition should be modified based on the fuel or fuel blends to achieve optimum performance. This study presented a performance analysis of a direct-injected (DI) diesel engine with a dynamometer fueled with diesel-tomato seed biodiesel (TSOB) blends employing ANOVA and universal nonlinear model based on ANN. The experiments were carried out under conditions of some independent variables including different engine loads (0, 50, 100%) and speed (1800, 2150, and 2500 rpm) for four diesel-biodiesel combinations (B0, B5, B10, and B20). In this research, the effect of these factors on dependent variables including power, torque, SFC, FC, and Exhaust Gas Temperature (EGT) are investigated. Duncan′s multi-domain test at a significance level of R < 0.01 shows that the highest and lowest of the torque and power are produced from B5 and B20, respectively. These results show that the lowest EGT of 613 K is related to B20 and the highest EGT is related to B5 and B10. The regression models showed that the torque decreases with increasing the engine speed and biodiesel percentage. These results also show that the highest and the lowest SFC is related to B0 and B20, respectively. The ANN model shows high capability of predicting the engine performance parameters and emissions, without running costly and time-consuming experiments with the histogram error of 0.004 and R = 0.96. It also proved that ANN is a non-linear model of choice to deal with these data, instead of multivariate linear regression employed for preliminary analysis.

Simultaneous Reduction of Oxides of Nitrogen and Smoke Emissions by Using EGR Combined With Particulate Trap in a DI Diesel Engine

2006 ◽  
Author(s):  
R. Anand ◽  
N. V. Mahalakshmi
Keyword(s):  
Diesel Engine ◽  
Low Cost ◽  
Direct Injection ◽  
Substantial Reduction ◽  
Load Condition ◽  
Engine Performance ◽  
Trapping Efficiency ◽  
Clay Material ◽  
Oxides Of Nitrogen ◽  
Di Diesel Engine

Exhaust gas recirculation (EGR) combined with particulate trap technology has proven to reduce nitrogen oxides (NOx) and smoke emissions simultaneously at relatively low cost compared to other reduction strategies. An experimental study was conducted on a single cylinder, direct injection (DI) diesel engine to study the effect of EGR on engine performance and emissions under constant speed of 1500 rpm at various loads. In the present work hot and cool EGR were used to control the formation of NOx in a D.I diesel engine. The findings of both hot and cool EGR are discussed and compared at full load condition corresponding to the maximum allowable EGR proportion of 15%. It is found that cool EGR has a substantial reduction in NOx and smoke emissions compared to hot EGR. Based on the above result it is found that suitable particulate trap which is cost effective and high trapping efficiency is needed before the EGR cooler to reduce the smoke emissions to meet the emission standards. In the present study a substrate made of clay material was used in the particulate trap. They were made into spheres and coated with copper and zinc oxide catalyst material. The results have shown that EGR combined with particulate trap simultaneously reduces the NOx and smoke emissions by 63% and 42% respectively where as it increases brake specific fuel consumption by 10% compared to baseline mode.

Investigating the Effect of Utilizing New Induction Manifold Designs on the Combustion Characteristics and Emissions of a Direct Injection Diesel Engine

2018 ◽  
Vol 140 (12) ◽  
Author(s):  
Mohamed A. Bassiony ◽  
Abdellatif M. Sadiq ◽  
Mohammed T. Gergawy ◽  
Samer F. Ahmed ◽  
Saud A. Ghani
Keyword(s):  
Diesel Engine ◽  
Peak Pressure ◽  
Direct Injection ◽  
Three Dimensional ◽  
Engine Performance ◽  
Combustion Characteristics ◽  
Maximum Pressure ◽  
Performance And Emissions ◽  
Di Diesel Engine ◽  
Dynamics Simulations

New induction manifold designs have been developed in this work to enhance the turbulence intensity and improve the mixing quality inside diesel engine cylinders. These new designs employ a spiral-helical shape with three different helical diameters (1D, 2D, 3D; where D is the inner diameter of the manifold) and three port outlet angles: 0 deg, 30 deg, and 60 deg. The new manifolds have been manufactured using three-dimensional printing technique. Computational fluid dynamics simulations have been conducted to estimate the turbulent kinetic energy (TKE) and the induction swirl generated by these new designs. The combustion characteristics that include the maximum pressure raise rate (dP/dθ) and the peak pressure inside the cylinder have been measured for a direct injection (DI) diesel engine utilizing these new manifold designs. In addition, engine performance and emissions have also been evaluated and compared with those of the normal manifold of the engine. It was found that the new manifolds with 1D helical diameter produce a high TKE and a reasonably strong induction swirl, while the ones with 2D and 3D generate lower TKEs and higher induction swirls than those of 1D. Therefore, dP/dθ and peak pressure were the highest with manifolds 1D, in particular manifold m (D, 30). Moreover, this manifold has provided the lowest fuel consumption with the engine load by about 28% reduction in comparison with the normal manifold. For engine emissions, m (D, 30) manifold has generated the lowest CO, SO2, and smoke emissions compared with the normal and other new manifolds as well, while the NO emission was the highest with this manifold.

scholarly journals The Differential Impact of Various Injection Pressures on the Exergy of a Diesel Engine Using Biodiesel-Diesel Fuel Blends

2021 ◽  
Vol 14 (1) ◽  
pp. 345
Author(s):  
Mostafa Kiani Deh Kiani ◽  
Sajad Rostami ◽  
Gholamhassan Najafi ◽  
Mohamed Mazlan
Keyword(s):  
Heat Transfer ◽  
Diesel Engine ◽  
Diesel Fuel ◽  
Exergy Analysis ◽  
Direct Injection ◽  
Injection Pressure ◽  
Cylinder Pressure ◽  
Fuel Blends ◽  
Lack Of Information ◽  
Good Agreement

Contrary to energy, exergy may be destroyed due to irreversibility. Exergy analysis can be used to reveal the location, and amount of energy losses of engines. Despite the importance of the exergy analysis, there is a lack of information in this area, especially when the engine is fueled with biodiesel–diesel fuel blends under various injection operating parameters. Thus, in this research, the exergy analysis of a direct-injection diesel engine using biodiesel–diesel fuel blends was performed. The fuel blends (B0, B20, B40, and B100) were injected into cylinders at pressures of 200 and 215 bars. Moreover, the simulation of exergy and energy analyses was done by homemade code. The simulation model was verified by compression of experimental and simulation in-cylinder pressure data. The results showed there was good agreement between simulation data and experimental ones. Results indicated that the highest level of in-cylinder pressure at injection pressure of 215 bars is more than that of 200 bars. Moreover, by increasing the percentage of biodiesel, the heat transfer exergy, irreversibility, burnt fuel, and exergy indicator decreased, but the ratio of these exergy parameters (except for heat transfer exergy) to fuel exergy increased. These ratios increased from 46 to 50.54% for work transfer exergy, 16.57 to 17.97% for irreversibility, and decreased from 16 to 15.49% for heat transfer exergy. In addition, these ratios at 215 bars are higher than at 200 bars for all fuels. However, with increasing the injection pressure and biodiesel concentration in fuel blends, the exergy and energy efficiencies increased.

Effect of Injection Parameters and Strategy on the Noise From a Single Cylinder Direct Injection Diesel Engine

2011 ◽  
Author(s):  
Sukhbir Singh Khaira ◽  
Amandeep Singh ◽  
Marcis Jansons
Keyword(s):  
Diesel Engine ◽  
Direct Injection ◽  
Injection Pressure ◽  
Combustion Noise ◽  
Injection Timing ◽  
Cylinder Pressure ◽  
Frequency Spectra ◽  
Single Cylinder ◽  
Direct Injection Diesel Engine ◽  
Injection Parameters

Acoustic noise emitted by a diesel engine generally exceeds that produced by its spark-ignited equivalent and may hinder the acceptance of this more efficient engine type in the passenger car market (1). This work characterizes the combustion noise from a single-cylinder direct-injection diesel engine and examines the degree to which it may be minimized by optimal choice of injection parameters. The relative contribution of motoring, combustion and resonance components to overall engine noise are determined by decomposition of in-cylinder pressure traces over a range of load, injection pressure and start of injection. The frequency spectra of microphone signals recorded external to the engine are correlated with those of in-cylinder pressure traces. Short Time Fourier Transformation (STFT) is applied to cylinder pressure traces to reveal the occurrence of motoring, combustion noise and resonance in the frequency domain over the course of the engine cycle. Loudness is found to increase with enhanced resonance, in proportion to the rate of cylinder pressure rise and under conditions of high injection pressure, load and advanced injection timing.

Effects of the Re-Entrant Bowl Geometry on a DI Turbocharged Diesel Engine Performance and Emissions—A CFD Approach

2010 ◽  
Vol 132 (12) ◽  
Author(s):  
S. Pasupathy Venkateswaran ◽  
G. Nagarajan
Keyword(s):  
Diesel Engine ◽  
Direct Injection ◽  
Combustion Process ◽  
Engine Performance ◽  
Maximum Diameter ◽  
Diffusion Combustion ◽  
Turbocharged Diesel Engine ◽  
Performance And Emissions ◽  
Di Diesel Engine ◽  
Fuel Mixing

The purpose of this study is to investigate the influence of re-entrant bowl geometry on both engine performance and combustion efficiency in a direct injection (DI), turbocharged diesel engine for heavy-duty applications. The piston bowl design is one of the most important factors that affect the air–fuel mixing and the subsequent combustion and pollutant formation processes in a DI diesel engine. The bowl geometry and dimensions, such as the pip region, bowl lip area, and toroidal radius, are all known to have an effect on the in-cylinder mixing and combustion processes. Based on the idea of enhancing diffusion combustion at the later stage of the combustion period, three different bowl geometries, namely, bowl 1 (baseline), bowl 2, and bowl 3 were selected and investigated. All the other relevant parameters, namely, compression ratio, maximum diameter of the bowl, squish clearance and injection rate were kept constant. A commercial CFD code STAR-CD was used to model the in-cylinder flows and combustion process, and experimental results of the baseline bowl were used to validate the numerical model. The simulation results show that, bowl 3 enhance the turbulence and hence results in better air-fuel mixing among all three bowls in a DI diesel engine. As a result, the indicated specific fuel consumption and soot emission reduced although the NOx emission is increased owing to better mixing and a faster combustion process. Globally, since the reduction in soot is larger (−46% as regards baseline) than the increase in NOx (+15% as regards baseline), it can be concluded that bowl 3 is the best trade-off between performance and emissions.

Experimental Study of Diesel Fuel Effects on Direct Injection (DI) Diesel Engine Performance and Pollutant Emissions

2007 ◽  
Vol 21 (5) ◽  
pp. 2642-2654 ◽  
Author(s):  
Theodoros C. Zannis ◽  
Dimitrios T. Hountalas ◽  
Roussos G. Papagiannakis
Keyword(s):  
Experimental Study ◽  
Diesel Engine ◽  
Diesel Fuel ◽  
Direct Injection ◽  
Engine Performance ◽  
Pollutant Emissions ◽  
Di Diesel Engine ◽  
Fuel Effects
Sign in / Sign up

Export Citation Format

Share Document