scholarly journals Simple Setup for Measuring the Response to Differential Mode Noise of Common Mode Chokes

Electronics ◽  
2020 ◽  
Vol 9 (3) ◽  
pp. 381 ◽  
Author(s):  
Pablo González-Vizuete ◽  
Carlos Domínguez-Palacios ◽  
Joaquín Bernal-Méndez ◽  
María A. Martín-Prats
Keyword(s):  
High Frequency ◽  
Electromagnetic Compatibility ◽  
Differential Mode ◽  
Common Mode ◽  
Low Frequencies ◽  
High Frequencies ◽  
Natural Modes ◽  
Magnetic Couplings ◽  
The Common ◽  
Conducted Emissions

This work presents a technique to measure the attenuation of differential mode noise provided by common mode chokes. The proposed setup is a simpler alternative to the balanced setup commonly employed to that end, and its main advantage is that it avoids the use of auxiliary circuits (baluns). We make use of a modal analysis of a high-frequency circuit model of the common mode choke to identify the natural modes actually excited both in the standard balanced setup and in the simpler alternative setup proposed here. This analysis demonstrates that both setups are equivalent at low frequencies and makes it possible to identify the key differences between them at high frequencies. To analyze the scope and interest of the proposed measurement technique we have measured several commercial common mode chokes and we have thoroughly studied the sensitivity of the measurements taken with the proposed setup to electric and magnetic couplings. We have found that the proposed setup can be useful for quick assessment of the attenuation provided by a common mode choke for differential mode noise in a frequency range that encompasses the frequencies where most electromagnetic compatibility regulations impose limits to the conducted emissions of electronic equipment.

scholarly journals Reliability of Boost PFC Converters with Improved EMI Filters

Electronics ◽  
2018 ◽  
Vol 7 (12) ◽  
pp. 413 ◽  
Author(s):  
Haoqi Zhu ◽  
Dongliang Liu ◽  
Xu Zhang ◽  
Feng Qu
Keyword(s):  
Electromagnetic Interference ◽  
High Frequency ◽  
Power Converter ◽  
Differential Mode ◽  
Conduction Path ◽  
Common Mode ◽  
Class B ◽  
The Common ◽  
Emi Filter ◽  
Stability Issues

The switching device in a power converter can produce very serious electromagnetic interference (EMI). In order to solve this problem and the associated reliability and stability issues, this article aimed to analyze and model the boost power factor correction (PFC) converter according to the EMI conduction path. The sources of common-mode (CM) and differential-mode (DM) noise of the boost PFC converter were analyzed, and the DM and CM equivalent circuits were deduced. Furthermore, high-frequency modeling of the common-mode inductor was developed using a precise model, and the EMI filter was designed. According to the Class B standard for EMI testing, it is better to restrain the EMI noise in the frequency range (150 kHz to 30 MHz) of the EMI conducted disturbance test. Using this method, a 2.4-kW PFC motor driving supply was designed, and the experimental results validate the analysis.

scholarly journals Reducing Conducted Emissions at the Output of Full-Bridge DCDC Converters with High Voltage Steps

Electronics ◽  
2021 ◽  
Vol 10 (12) ◽  
pp. 1373
Author(s):  
Pablo González-Vizuete ◽  
Joaquín Bernal-Méndez ◽  
María A. Martín-Prats
Keyword(s):  
High Voltage ◽  
Low Voltage ◽  
Power Converter ◽  
Differential Mode ◽  
Common Mode ◽  
High Frequencies ◽  
Output Terminal ◽  
Lc Filter ◽  
The Impact ◽  
Conducted Emissions

In this work, we analyze the impact of output filter design techniques aimed to reduce conducted emissions at the output of a DCDC power converter. A thorough analysis, based on high-frequency circuit models of the converter, is performed to assess expected improvements offered by different design strategies. This analysis is then confronted with measurements of conducted emissions at the output of a 300 W 48 V to 12 V Phase Shift Full Bridge (PSFB) prototype. Those experimental results demonstrate that a symmetric arrangement of the output LC filter and a direct bonding of the return output terminal of the converter to chassis are effective to reduce common mode conducted emissions at the output. Those results also demonstrate that the symmetry of the output LC filter can reduce conducted emissions in differential mode at high frequencies, where common mode to differential mode conversion is the predominant contribution to differential mode noise. However, direct bonding to chassis of the return output terminal may be ineffective at high frequencies due to the parasitic inductance associated with this connection. Main conclusions drawn for this analysis are applicable in general for isolated converters with a high voltage step between high and low voltage sides. Since the techniques of reduction of conducted emissions studied here do not increase the number of filter components, they are especially suitable for applications where high power density is an important requirement, e.g., aerospace or automotive applications.

Tunable balanced to balanced filtering power divider with high common-mode suppression

Frequenz ◽  
2020 ◽  
Vol 74 (7-8) ◽  
pp. 263-270
Author(s):  
Cao Zeng ◽  
Xue Han Hu ◽  
Feng Wei ◽  
Xiao Wei Shi
Keyword(s):  
Return Loss ◽  
High Selectivity ◽  
Power Divider ◽  
Center Frequency ◽  
Differential Mode ◽  
Common Mode ◽  
Mode Suppression ◽  
The Common ◽  
Equal Power ◽  
Good Agreement

AbstractIn this paper, a tunable balanced-to-balanced in-phase filtering power divider (FPD) is designed, which can realize a two-way equal power division with high selectivity and isolation. A differential-mode (DM) passband with a steep filtering performance is realized by applying microstrip stub-loaded resonators (SLRs). Meanwhile, six varactors are loaded to the SLRs to achieve the center frequency (CF) and bandwidth adjustment, respectively. U-type microstrip lines integrated with stepped impedance slotline resonators are utilized as the differential feedlines, which suppress the common-mode (CM) intrinsically, making the DM responses independent of the CM ones. A tuning center frequency from 3.2 to 3.75 GHz and a fractional bandwidth (12.1–17.6%) with more than 10 dB return loss and less than 2.3 dB insertion loss can be achieved by changing the voltage across the varactors. A good agreement between the simulated and measured results is observed. To the best of authors' knowledge, the proposed balanced-to-balanced tunable FPD is first ever reported.

scholarly journals The Estimation of Hydrometeor Profiles from Wideband Microwave Observations

2000 ◽  
Vol 39 (10) ◽  
pp. 1645-1656 ◽  
Author(s):  
Gail M. Skofronick-Jackson ◽  
James R. Wang
Keyword(s):  
High Frequency ◽  
Cloud Water ◽  
Tropical Ocean ◽  
Low Frequencies ◽  
High Frequencies ◽  
Atmospheric Research ◽  
Brightness Temperatures ◽  
Microphysical Properties ◽  
Ice Microphysics ◽  
Updraft Region

Abstract Profiles of the microphysical properties of clouds and rain cells are essential in many areas of atmospheric research and operational meteorology. To enhance the understanding of the nonlinear and underconstrained relationships between cloud and hydrometeor microphysical profiles and passive microwave brightness temperatures, estimations of cloud profiles for an anvil region, a convective region, and an updraft region of an oceanic squall were performed. The estimations relied on comparisons between radiative transfer calculations of incrementally estimated microphysical profiles and concurrent dual-altitude wideband brightness temperatures from the 22 February 1993 flight during the Tropical Ocean and Global Atmosphere Coupled Ocean–Atmosphere Response Experiment. The wideband observations (10–220 GHz) are necessary for estimating cloud profiles reaching up to 20 km. The low frequencies enhance the rain and cloud water profiles, and the high frequencies are required to detail the higher-altitude ice microphysics. A microphysical profile was estimated for each of the three regions of the storm. Each of the three estimated profiles produced calculated brightness temperatures within ∼10 K of the observations. A majority of the total iterative adjustments were to the estimated profile’s frozen hydrometeor characteristics and were necessary to match the high-frequency calculations with the observations. This requirement indicates a need to validate cloud-resolving models using high frequencies. Some difficulties matching the 37-GHz observation channels on the DC-8 and ER-2 aircraft with the calculations simulated at the two aircraft heights (∼11 km and 20 km, respectively) were noted, and potential causes were presented.

scholarly journals Novel Negative Capacitance and Conductance in All Temperatures and Voltages of Au/CNTs/n-Si/Al at Low and High Frequencies

2021 ◽  
Author(s):  
A. Ashery ◽  
Samia Gad ◽  
A. E.H. Gaballah ◽  
G. M. Turky
Keyword(s):  
Carbon Nanotube ◽  
High Frequency ◽  
Series Resistance ◽  
Negative Capacitance ◽  
Donor Concentration ◽  
Low Frequencies ◽  
High Frequencies ◽  
Depletion Width ◽  
Density Surface ◽  
P Type

Abstract The structure of carbon nanotube CNTs functioning as p-type material deposited over n-type silicon to produce heterojunction of Au/CNTs/n-Si/Al is presented in this study.This work explored the capacitance and conductance at various frequencies, temperatures, and voltages, the novelty here is that negative capacitance and conductance were observed at high frequencies in all temperatures and voltages, whereas capacitance appeared at both high and low frequencies, such as (2x107,1x107,1x102,10) Hz. At high-frequency f = 2x107 Hz, the capacitance raises while the conductance decreases; at all temperatures and voltages, the capacitance and conductance exhibit the same behavior at particular frequencies such as 1x106,1x105,1x104,1x103Hz, however their behavior differs at 2x107,1x107, 1x102 and 10Hz. Investigating the reverse square capacitance with voltage yielded the energy fermi (Ef), density surface of states (Nss), depletion width (Wd), barrier height, series resistance, and donor concentration (Nd)

Evaluation of Thermal Degradation of 2.25Cr-1Mo Steel by High Frequency Ultrasonic Attenuation Measurement

2005 ◽  
Vol 475-479 ◽  
pp. 257-260 ◽  
Author(s):  
Jai Won Byeon ◽  
C.S. Kim ◽  
S.I. Kwun ◽  
S.J. Hong
Keyword(s):  
Attenuation Coefficient ◽  
High Frequency ◽  
Ultrasonic Attenuation ◽  
Attenuation Coefficients ◽  
Low Frequencies ◽  
High Frequencies ◽  
Noticeable Increase ◽  
Mean Size ◽  
Longitudinal Ultrasonic Wave ◽  
Degradation Time

It was attempted to assess nondestructively the degree of isothermal degradation of 2.25Cr-1Mo steel by using high frequency longitudinal ultrasonic wave. Microstructural parameter (mean size of carbides), mechanical property (Vickers hardness) and ultrasonic attenuation coefficient were measured for the 2.25Cr-1Mo steel isothermally degraded at 630°C for up to 4800 hours in order to find the correlation among these parameters. The ultrasonic attenuation coefficients at high frequencies (over 35MHz) were observed to increase rapidly in the initial 1000 hours of degradation time and then slowly thereafter, while the ones at low frequencies showed no noticeable increase. Ultrasonic attenuation at high frequencies increased as a function of mean size of carbides. Ultrasonic attenuation coefficient was found to have a linear correlation with the hardness, and suggested accordingly as a potential nondestructive evaluation parameter for assessing the mechanical strength reduction of the isothermally degraded 2.25Cr-1Mo steel.

Fully Differential Class-AB OTA with Improved CMRR

2017 ◽  
Vol 26 (11) ◽  
pp. 1750169 ◽  
Author(s):  
Francesco Centurelli ◽  
Pietro Monsurrò ◽  
Gaetano Parisi ◽  
Pasquale Tommasino ◽  
Alessandro Trifiletti
Keyword(s):  
Cmos Technology ◽  
Current Mirror ◽  
Differential Mode ◽  
Common Mode ◽  
Common Mode Rejection Ratio ◽  
Class Ab ◽  
Fully Differential ◽  
Rejection Ratio ◽  
Mode Behavior ◽  
The Common

This paper presents a fully differential class-AB current mirror OTA that improves the common-mode behavior of a topology that presents very good differential-mode performance but poor common-mode rejection ratio (CMRR). The proposed solution requires a low-current auxiliary circuit driven by the input signal, to compensate the effect of the common-mode input component. Simulations in 40-nm CMOS technology show a net reduction of common-mode gain of more than 90[Formula: see text]dB without affecting the differential-mode behavior; a sample-and-hold amplifier exploiting the proposed amplifier has also been simulated.

Sign in / Sign up

Export Citation Format

Share Document