scholarly journals Tracking and Synchronization with Inversion-Based ILC for a Multi-Actuator-Driven Wafer Inspection Cartridge Transport Robot System

Electronics ◽  
2021 ◽  
Vol 10 (23) ◽  
pp. 2904
Author(s):  
Dong Jun Oh ◽  
Seung Guk Baek ◽  
Kyung-Tae Nam ◽  
Ja Choon Koo
Keyword(s):  
Iterative Learning Control ◽  
Control Method ◽  
Iterative Learning ◽  
Synchronization Control ◽  
System Control ◽  
Input Output ◽  
Semiconductor Wafer ◽  
Robot System ◽  
Output Data ◽  
Wafer Inspection

This paper proposes a simple tracking and synchronization control of a dual-drive system using inversion-based iterative learning control (IILC), which reformulates the model at each iteration based on input/output data. By the power of the IILC, this work simplifies the dual-actuator-driven dynamic system control problem that is normally addressed with a MIMO method. This work also shows the potential of the IILC for nonlinear system applications by reformulating the model at each iteration based on the input/output data. An analytical representation of the iteration-varying IILC followed by simulations is provided. A set of physical system testings with a dual-motor gantry and a semiconductor wafer inspection robotic system are carried out to verify the control method.

Chaotic motion control of a vibro-impact system based on data-driven control method

2021 ◽  
pp. 107754632110433
Author(s):  
Xiao-juan Wei ◽  
Ning-zhou Li ◽  
Wang-cai Ding
Keyword(s):  
Motion Control ◽  
Data Model ◽  
Chaotic Motion ◽  
Control Method ◽  
Data Driven ◽  
Damping Coefficient ◽  
Input Output ◽  
Output Data ◽  
Controlled System ◽  
Impact System

For the chaotic motion control of a vibro-impact system with clearance, the parameter feedback chaos control strategy based on the data-driven control method is presented in this article. The pseudo-partial-derivative is estimated on-line by using the input/output data of the controlled system so that the compact form dynamic linearization (CFDL) data model of the controlled system can be established. And then, the chaos controller is designed based on the CFDL data model of the controlled system. And the distance between two adjacent points on the Poincaré section is used as the judgment basis to guide the controller to output a small perturbation to adjust the damping coefficient of the controlled system, so the chaotic motion can be controlled to a periodic motion by dynamically and slightly adjusting the damping coefficient of the controlled system. In this method, the design of the controller is independent of the order of the controlled system and the structure of the mathematical model. Only the input/output data of the controlled system can be used to complete the design of the controller. In the simulation experiment, the effectiveness and feasibility of the proposed control method in this article are verified by simulation results.

Iterative learning control of robot based on artificial bee colony algorithm

2019 ◽  
Vol 233 (9) ◽  
pp. 1221-1238
Author(s):  
Wanqiang Xi ◽  
Yaoyao Wang ◽  
Bai Chen ◽  
Hongtao Wu
Keyword(s):  
Iterative Learning Control ◽  
Degrees Of Freedom ◽  
Artificial Bee Colony Algorithm ◽  
Artificial Bee Colony ◽  
Control Method ◽  
Learning Control ◽  
Iterative Learning ◽  
Industrial Robots ◽  
Control Effect ◽  
Bee Colony

For the repetitive motion control, inaccurate model, and other issues of industrial robots, this article presents a novel control method that the proportion differentiation-type iterative learning parameters are self-tuning based on artificial bee colony algorithm. Considering the influence of the numerical value of iterative learning parameters on the control system, especially in the early iteration, the control effect is not satisfactory. Thus, the artificial bee colony algorithm is introduced in this article. Using bee colony as search unit, the parameters in iterative learning are optimized through the exchange of information and the survival of fittest between them. And then the optimized results are returned to iterative learning control algorithm. Finally, the digital simulation of a two-degrees-of-freedom manipulator and the experimental verification of a cable-driven robot with its first two joints are carried out. The results show that the iterative learning control based on the artificial bee colony algorithm has faster convergence and better control effect than the iterative learning control with fixed parameters.

scholarly journals Novel Fuzzy PID-Type Iterative Learning Control for Quadrotor UAV

Sensors ◽  
2018 ◽  
Vol 19 (1) ◽  
pp. 24 ◽  
Author(s):  
Jian Dong ◽  
Bin He
Keyword(s):  
Fuzzy Control ◽  
Iterative Learning Control ◽  
Control Method ◽  
External Disturbance ◽  
Learning Control ◽  
Iterative Learning ◽  
System Stability ◽  
Learning Gain ◽  
Control Precision ◽  
Quadrotor Aircraft

Due to the under-actuated and strong coupling characteristics of quadrotor aircraft, traditional trajectory tracking methods have low control precision, and poor anti-interference ability. A novel fuzzy proportional-interactive-derivative (PID)-type iterative learning control (ILC) was designed for a quadrotor unmanned aerial vehicle (UAV). The control method combined PID-ILC control and fuzzy control, so it inherited the robustness to disturbances and system model uncertainties of the ILC control. A new control law based on the PID-ILC algorithm was introduced to solve the problem of chattering caused by an external disturbance in the ILC control alone. Fuzzy control was used to set the PID parameters of three learning gain matrices to restrain the influence of uncertain factors on the system and improve the control precision. The system stability with the new design was verified using Lyapunov stability theory. The Gazebo simulation showed that the proposed design method creates effective ILC controllers for quadrotor aircraft.

Sign in / Sign up

Export Citation Format

Share Document