scholarly journals Compact 2 × 2 Circularly Polarized Aperture-Coupled Antenna Array for Ka-Band Satcom-on-the-Move Applications

Electronics ◽  
2021 ◽  
Vol 10 (14) ◽  
pp. 1621
Author(s):  
Hisham Baghdadi ◽  
Guillermo Royo ◽  
Ismael Bel ◽  
Francisco Javier Cortés ◽  
Santiago Celma
Keyword(s):  
Circular Polarization ◽  
Antenna Array ◽  
Printed Circuit Board ◽  
Layer Structure ◽  
Axial Ratio ◽  
Beam Width ◽  
Unit Cell ◽  
Circuit Board ◽  
High Yield ◽  
Ka Band

This paper presents a novel design of a wideband circular polarization 2 × 2 microstrip antenna array working at Ka-band frequencies, from 27.5 to 31 GHz. This module is highly integrable with new silicon beamformer chips, creating a unit cell that can be part of a large electronically steerable antenna for compact, ultra-low-profile, Satcom-on-the-move (SOTM) platforms. A multi-layer structure fabricated in standard printed circuit board (PCB) technology with high-yield substrates has been used. The radiating elements consist of double-stacked circular patches housed in a cavity and fed by H-shaped aperture coupling. It achieves a bandwidth of 16.5 % with a wide beam-width of 95° in the desired band, which is necessary for wide scanning angles in a large phased array. In the 2 × 2 unit cell, the antenna elements are distributed by means of a sequential rotation technique where the separation between two of them is 5.3 mm in the XY-plane. Broadside beam-widths ranging from 53.4° at 27.5 GHz to 42.1° at 31 GHz are achieved, with boresight directivities from 10.7 to 12.9 dBi, respectively, in both the RHCP and LHCP polarization. Moreover, mutual coupling levels below −20 dB and an axial ratio less than 3 dB in the whole band guarantee a good circular polarization purity.

scholarly journals Ka-Band Slot-Microstrip-Covered and Waveguide-Cavity-Backed Monopulse Antenna Array

2014 ◽  
Vol 2014 ◽  
pp. 1-5 ◽  
Author(s):  
Li-Ming Si ◽  
Yong Liu ◽  
Yongjun Huang ◽  
Weiren Zhu
Keyword(s):  
Antenna Array ◽  
Printed Circuit Board ◽  
Low Cost ◽  
Dielectric Substrate ◽  
Circuit Board ◽  
Slot Antenna ◽  
Ka Band ◽  
Operating Bandwidth ◽  
The Difference ◽  
Waveguide Slot Antenna

A slot-microstrip-covered and waveguide-cavity-backed monopulse antenna array is proposed for high-resolution tracking applications at Ka-band. The monopulse antenna array is designed with a microstrip with2×32slots, a waveguide cavity, and a waveguide monopulse comparator, to make the structure simple, reduce the feeding network loss, and increase the frequency bandwidth. The2×32slot-microstrip elements are formed by a metal clad dielectric substrate and slots etched in the metal using the standard printed circuit board (PCB) process with dimensions of 230 mm  ×  10 mm. The proposed monopulse antenna array not only maintains the advantages of the traditional waveguide slot antenna array, but also has the characteristics of wide bandwidth, high consistence, easy of fabrication, and low cost. From the measured results, it exhibits good monopulse characteristics, including the following: the maximum gains of sum pattern are greater than 24 dB, the 3 dB beamwidth of sum pattern is about 2.2 degrees, the sidelobe levels of the sum pattern are less than −18 dB, and the null depths of the difference pattern are less than −25 dB within the operating bandwidth between 33.65 GHz and 34.35 GHz for VSWR ≤ 2.

scholarly journals A Millimeter-Wave Wideband Circularly Polarized Planar Spiral Antenna Array with Unequal Amplitude Feeding Network

2021 ◽  
Vol 2021 ◽  
pp. 1-10
Author(s):  
Huakang Chen ◽  
Yu Shao ◽  
Zhangjian He ◽  
Changhong Zhang ◽  
Zhizhong Zhang
Keyword(s):  
Antenna Array ◽  
Millimeter Wave ◽  
Printed Circuit Board ◽  
Low Cost ◽  
Axial Ratio ◽  
Circuit Board ◽  
Impedance Bandwidth ◽  
Side Lobe Level ◽  
Archimedean Spiral ◽  
Circularly Polarized

A 2 × 2 wideband circularly polarized (CP) antenna array operating at millimeter wave (mmWave) band is presented. The array element is a wideband CP Archimedean spiral radiator with special-shaped ring slot. The elements are fed by an unequal amplitude (UA) feeding network based on a microstrip line (MSL) power divider. The side lobe level is improved by this UA feeding network. In addition, a cross slot is employed to isolate the elements for decoupling. A prototype is fabricated, and the measured results show that the proposed array achieves an impedance bandwidth (IBW) of 6.31 GHz (22.5% referring to 28 GHz) and an axial ratio bandwidth (ARBW) of 7.32 GHz (26.1% referring to 28 GHz). The peak gain of the proposed array is 11.3 dBic, and the gain is greater than 9.3 dBic within the whole desired band (from 25 GHz to 31 GHz). The proposed array consists of only one substrate layer and can be built by the conventional printed circuit board technology. Attributed to the characteristics of wide bandwidth, simple structure, low profile, and low cost, the proposed antenna array has a great potential in mmWave wireless communications.

scholarly journals Circularly Polarized Triband Printed Quasi-Yagi Antenna for Millimeter-Wave Applications

2015 ◽  
Vol 2015 ◽  
pp. 1-9 ◽  
Author(s):  
Dalia M. Elsheakh ◽  
Magdy F. Iskander
Keyword(s):  
Circular Polarization ◽  
Printed Circuit Board ◽  
Ground Plane ◽  
Axial Ratio ◽  
Circuit Board ◽  
Impedance Bandwidth ◽  
60 Ghz ◽  
Antenna Structure ◽  
Circularly Polarized ◽  
Yagi Antenna

This paper describes the design and development of a triband with circularly polarized quasi-Yagi antenna for ka-band and short range wireless communications applications. The proposed antenna consists of an integrated balun-fed printed dipole, parasitic folded dipole and a short strip, and a modified ground plane. The antenna structure, together with the parasitic elements, is designed to achieve circular polarization and triband operating at resonant frequencies of 13.5 GHz, 30 GHz, and 60 GHz. Antenna design was first simulated using HFSS ver.14, and the obtained results were compared with experimental measurements on a prototype developed on a single printed circuit board. Achieved characteristics include −10 dB impedance bandwidth at the desired bands, circular polarization axial ratioAR<3 dB, front to back ratio of 6 dB, gain value of about 4 dBi, and average radiation efficiency of 60%. The paper includes comparison between simulation and experimental results.

A Novel Wideband transition from Substrate Integrated Waveguide to Rectangular Waveguide

2020 ◽  
Vol 10 ◽  
Author(s):  
Keyur Mahant ◽  
Hiren Mewada ◽  
Amit Patel ◽  
Alpesh Vala ◽  
Jitendra Chaudhari
Keyword(s):  
Rectangular Waveguide ◽  
Printed Circuit Board ◽  
Low Cost ◽  
Single Layer ◽  
Circuit Board ◽  
Substrate Integrated Waveguide ◽  
Ka Band ◽  
Better Than ◽  
Millimeter Wave Circuits ◽  
Wideband Transition

Aim: In this article, wideband substrate integrated waveguide (SIW) and rectangular waveguide (RWG) transition operating in Ka-band is proposed Objective: In this article, wideband substrate integrated waveguide (SIW) and rectangular waveguide (RWG) transition operating in Ka-band is proposed. Method: Coupling patch etched on the SIW cavity to couple the electromagnetic energy from SIW to RWG. Moreover, metasurface is introduced into the radiating patch to enhance bandwidth. To verify the functionality of the proposed structure back to back transition is designed and fabricated on a single layer substrate using standard printed circuit board (PCB) fabrication technology. Results: Measured results matches with the simulation results, measured insertion loss is less than 1.2 dB and return loss is better than 3 dB for the frequency range of 28.8 to 36.3 GHz. By fabricating transition with 35 SRRs bandwidth of the proposed transition can be improved. Conclusion: The proposed transition has advantages like compact in size, easy to fabricate, low cost and wide bandwidth. Proposed structure is a good candidate for millimeter wave circuits and systems.

scholarly journals A compact low-noise frontend for interleaved Rx/Tx arrays at K-/Ka-Band

2021 ◽  
pp. 1-7
Author(s):  
Anton Sieganschin ◽  
Thomas Jaschke ◽  
Arne F. Jacob
Keyword(s):  
Insertion Loss ◽  
Printed Circuit Board ◽  
Noise Figure ◽  
Low Noise ◽  
Single Band ◽  
Circuit Board ◽  
Dual Band ◽  
Ka Band ◽  
Compression Properties ◽  
The Individual

Abstract This contribution deals with a frontend for interleaved receive (Rx)-/transmit (Tx)-integrated phased arrays at K-/Ka-band. The circuit is realized in printed circuit board technology and feeds dual-band Rx/Tx- and single-band Tx-antenna elements. The dual-band element feed is composed of a substrate-integrated waveguide (SIW) diplexer with low insertion loss, a low-noise amplifier (LNA), a bandpass filter, and several passive transitions. The compression properties of the LNA are identified through two-tone measurements. The results dictate the maximum allowable output power of the power amplifier. The single band feed consists of a SIW with several transitions. Simulation and measurement results of the individual components are presented. The frontend is assembled and measured. It exhibits an Rx noise figure of 2 dB, a Tx insertion loss of ~ 2.9 dB, and an Rx/Tx-isolation of 70 dB. The setup represents the unit cell of a full array and thus complies with the required half-wave spacing at both Rx and Tx.

Design of the Ka-Band Satellite Antenna by Parallel Differential Evolution

2014 ◽  
Vol 556-562 ◽  
pp. 2194-2197 ◽  
Author(s):  
Jin Cui Guo ◽  
Xiao Qiu Liu ◽  
Wei Zhang ◽  
Bin Quan He
Keyword(s):  
Differential Evolution ◽  
Circular Polarization ◽  
Method Of Moments ◽  
Beam Width ◽  
Wide Beam ◽  
Satellite Antenna ◽  
Ka Band ◽  
Left Hand ◽  
Computing Platform

This paper designs a Ka-Band satellite antenna using parallel differential evolution (DE). The antenna is of wide beam-width and left hand circular polarization (LHCP). The electromagnetic numerical value is calculated by the improved software NEC2 based on the method of moments. The parallel differential evolution computing platform consists of some computers and MPI is used as the messaging protocol among computers. The single-arm Ka-Band antenna with 8-segments designed in this method has obtained very good performance including gains, axial ratios and VSWRs in a shorter period.

scholarly journals Mobile-Phone Antenna Array with Diamond-Ring Slot Elements for 5G Massive MIMO Systems

Electronics ◽  
2019 ◽  
Vol 8 (5) ◽  
pp. 521 ◽  
Author(s):  
Naser Ojaroudi Parchin ◽  
Haleh Jahanbakhsh Basherlou ◽  
Mohammad Alibakhshikenari ◽  
Yasser Ojaroudi Parchin ◽  
Yasir I. A. Al-Yasir ◽  
...  
Keyword(s):  
Mobile Phone ◽  
Antenna Array ◽  
Massive Mimo ◽  
Printed Circuit Board ◽  
High Efficiency ◽  
Mimo Systems ◽  
Circuit Board ◽  
Slot Antenna ◽  
Impedance Bandwidth ◽  
Diamond Ring

A design of mobile-phone antenna array with diamond-ring slot elements is proposed for fifth generation (5G) massive multiple-input/multiple-output (MIMO) systems. The configuration of the design consists of four double-fed diamond-ring slot antenna elements placed at different corners of the mobile-phone printed circuit board (PCB). A low-cost FR-4 dielectric with an overall dimension of 75 × 150 mm2 is used as the design substrate. The antenna elements are fed by 50-Ohm L-shaped microstrip-lines. Due to the orthogonal placement of microstrip feed lines, the diamond-ring slot elements can exhibit the polarization and radiation pattern diversity characteristic. A good impedance bandwidth (S11 ≤ −10 dB) of 3.2–4 GHz has been achieved for each antenna radiator. However, for S11 ≤ −6 dB, this value is 3–4.2 GHz. The proposed design provides the required radiation coverage of 5G smartphones. The performance of the proposed MIMO antenna design is examined using both simulation and experiment. High isolation, high efficiency and sufficient gain-level characteristics have been obtained for the proposed MIMO smartphone antenna. In addition, the calculated total active reflection coefficient (TARC) and envelope correlation coefficient (ECC) of the antenna elements are very low over the whole band of interest which verify the capability of the proposed multi-antenna systems for massive MIMO and diversity applications. Furthermore, the properties of the design in Data-mode/Talk-mode are investigated and presented.

scholarly journals A Series-Fed Linear Substrate-Integrated Dielectric Resonator Antenna Array for Millimeter-Wave Applications

2018 ◽  
Vol 2018 ◽  
pp. 1-6 ◽  
Author(s):  
Ke Gong ◽  
Xue Hui Hu ◽  
Peng Hu ◽  
Bing Jie Deng ◽  
You Chao Tu
Keyword(s):  
Antenna Array ◽  
Millimeter Wave ◽  
Dielectric Resonator ◽  
Return Loss ◽  
Printed Circuit Board ◽  
Circuit Board ◽  
Dielectric Resonator Antenna ◽  
Radiation Patterns ◽  
Feeding Structure ◽  
Broadside Radiation

A series-fed linear substrate-integrated dielectric resonator antenna array (SIDRAA) is presented for millimeter-wave applications, in which the substrate-integrated dielectric resonator antenna (SIDRA) elements and the feeding structure can be codesigned and fabricated using the same planar process. A prototype 4 × 1 SIDRAA is designed at Ka-band and fabricated with a two-layer printed circuit board (PCB) technology. Four SIDRAs are implemented in the Rogers RT6010 substrate using the perforation technique and fed by a compact substrate-integrated waveguide (SIW) through four longitudinal coupling slots within the Rogers RT5880 substrate. The return loss, radiation patterns, and antenna gain were experimentally studied, and good agreement between the measured and simulated results is observed. The SIDRAA example provides a bandwidth of about 10% around 34.5 GHz for 10 dB return loss and stable broadside radiation patterns with the peak gain of 10.5–11.5 dBi across the band.

scholarly journals High-Gain Circularly-Polarized Elliptically-Annular Antenna-Array with Reduced Side-Lobe Level

2020 ◽  
Vol 9 (4) ◽  
pp. 2319-2325
Keyword(s):  
Circular Polarization ◽  
Antenna Array ◽  
Satellite Communication ◽  
Axial Ratio ◽  
Side Lobe ◽  
High Gain ◽  
Side Lobe Level ◽  
Single Element ◽  
Circularly Polarized ◽  
Gain Enhancement

A single feed microstrip patch elliptically annular antenna array has been proposed for high gain circularly polarized (CP) radiation. An array of elliptically annular patches antenna resonates at a frequency of 3.77 GHz which can be used in satellite communication and radar application. A corporate feed network with quarter-wave transformer has been used for uniform excitation of all the array elements. Thus a good circular polarization is obtained by using a single feed with enhanced gain 15.62 dB compared to single patch. The radiation pattern, axial ratio and input impedance of the proposed elliptically annular antenna array is compared with single element elliptically annular antenna. A substantial gain enhancement with low side lobe level (SLL) is observed keeping circular polarization intact. Further, simulated and measured results of the proposed antenna array have been compared and found that axial ratio and gain are in good agreement.

Sign in / Sign up

Export Citation Format

Share Document