scholarly journals Increasing the Directivity of Resonant Cavity Antennas with Nearfield Transformation Meta-Structure Realized with Stereolithograpy

Electronics ◽  
2021 ◽  
Vol 10 (3) ◽  
pp. 333
Author(s):  
Sujan Shrestha ◽  
Hijab Zahra ◽  
Muhammad Ali Babar Abbasi ◽  
Mohsen Asadnia ◽  
Syed Muzahir Abbas
Keyword(s):  
Additive Manufacturing ◽  
Low Cost ◽  
Resonant Cavity ◽  
Light Weight ◽  
Unit Cells ◽  
Planar Approach ◽  
Half Power

A simple, nearfield transformation meta-structure is proposed to increase the directivity of resonant cavity antennas (RCA). The meta-structure is comprised of 14 × 14 meta-atoms or so called “unit-cells”, adding localized phase delays in the aperture of the RCA and thus increasing its broadside directivity. A prototype of the meta-structure is additively manufactured using the stereolithograpy process and has a profile of 0.56λ. With the meta-structure integrated with the RCA, it demonstrates a measured broadside directivity of 20.15 dBi without affecting its half-power directivity bandwidth. Benefiting from additive manufacturing, the proposed approach is a simple, light-weight, low-cost, and planar approach that can be tailored to achieve medium-to-high gains with RCAs.

Techniques for assessing the performance of circuit materials at microwave and millimetre-wave frequencies

2003 ◽  
Vol 783 ◽  
Author(s):  
Charles E Free
Keyword(s):  
Loss Tangent ◽  
Good Accuracy ◽  
Low Cost ◽  
Resonant Cavity ◽  
New Technique ◽  
Millimetre Wave ◽  
A New Technique

This paper discusses the techniques that are available for characterising circuit materials at microwave and millimetre wave frequencies. In particular, the paper focuses on a new technique for measuring the loss tangent of substrates at mm-wave frequencies using a circular resonant cavity. The benefits of the new technique are that it is simple, low cost, capable of good accuracy and has the potential to work at high mm-wave frequencies.

Fused Ambipolar Aza-isoindigos with NIR absorption

2021 ◽  
Author(s):  
Liping Yao ◽  
Danlei Zhu ◽  
Hailiang Liao ◽  
Sheik Haseena ◽  
Mahesh kumar Ravva ◽  
...  
Keyword(s):  
Organic Semiconductors ◽  
High Performance ◽  
Low Cost ◽  
Light Weight ◽  
The Past ◽  
Pi Conjugated ◽  
Nir Absorption ◽  
Conjugated Organic Semiconductors

Due to their advantages of low-cost, light-weight, and mechanical flexibility, much attention has been focused on pi-conjugated organic semiconductors. In the past decade, although many materials with high performance has...

Influence of Specimen Layout on 17-4PH (AISI 630) Alloys Fabricated by Low-Cost Additive Manufacturing

2021 ◽  
Author(s):  
Chanun Suwanpreecha ◽  
Phanuphak Seensattayawong ◽  
Vorawat Vadhanakovint ◽  
Anchalee Manonukul
Keyword(s):  
Additive Manufacturing ◽  
Low Cost

Printing of Low Cost Sensors by Additive Manufacturing

2021 ◽  
Author(s):  
Salman Ahmad ◽  
Muhammad Shakeel ◽  
Nadeem Iqbal ◽  
Mohsin Amin ◽  
Khalid Rahman
Keyword(s):  
Additive Manufacturing ◽  
Low Cost

scholarly journals Smooth Design of 3D Self-Supporting Topologies Using Additive Manufacturing Filter and SEMDOT

2020 ◽  
Vol 11 (1) ◽  
pp. 238
Author(s):  
Yun-Fei Fu ◽  
Kazem Ghabraie ◽  
Bernard Rolfe ◽  
Yanan Wang ◽  
Louis N. S. Chiu
Keyword(s):  
Additive Manufacturing ◽  
Compliant Mechanism ◽  
Optimization Method ◽  
Light Weight ◽  
Design For Additive Manufacturing ◽  
Compliance Minimization ◽  
Performance Requirements ◽  
Specific Performance ◽  
Smooth Design ◽  
Compliant Mechanism Design

The smooth design of self-supporting topologies has attracted great attention in the design for additive manufacturing (DfAM) field as it cannot only enhance the manufacturability of optimized designs but can obtain light-weight designs that satisfy specific performance requirements. This paper integrates Langelaar’s AM filter into the Smooth-Edged Material Distribution for Optimizing Topology (SEMDOT) algorithm—a new element-based topology optimization method capable of forming smooth boundaries—to obtain print-ready designs without introducing post-processing methods for smoothing boundaries before fabrication and adding extra support structures during fabrication. The effects of different build orientations and critical overhang angles on self-supporting topologies are demonstrated by solving several compliance minimization (stiffness maximization) problems. In addition, a typical compliant mechanism design problem—the force inverter design—is solved to further demonstrate the effectiveness of the combination between SEMDOT and Langelaar’s AM filter.

scholarly journals Gold, Silver, and Electrum Electroless Plating on Additively Manufactured Laser Powder-Bed Fusion AlSi10Mg Parts: A Review

Coatings ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 422
Author(s):  
Dana Ashkenazi ◽  
Alexandra Inberg ◽  
Yosi Shacham-Diamand ◽  
Adin Stern
Keyword(s):  
Additive Manufacturing ◽  
Low Cost ◽  
Ion Beam ◽  
Surface Finishing ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
Finishing Process ◽  
Gold Silver ◽  
3D Printed

Additive manufacturing (AM) revolutionary technologies open new opportunities and challenges. They allow low-cost manufacturing of parts with complex geometries and short time-to-market of products that can be exclusively customized. Additive manufactured parts often need post-printing surface modification. This study aims to review novel environmental-friendly surface finishing process of 3D-printed AlSi10Mg parts by electroless deposition of gold, silver, and gold–silver alloy (e.g., electrum) and to propose a full process methodology suitable for effective metallization. This deposition technique is simple and low cost method, allowing the metallization of both conductive and insulating materials. The AlSi10Mg parts were produced by the additive manufacturing laser powder bed fusion (AM-LPBF) process. Gold, silver, and their alloys were chosen as coatings due to their esthetic appearance, good corrosion resistance, and excellent electrical and thermal conductivity. The metals were deposited on 3D-printed disk-shaped specimens at 80 and 90 °C using a dedicated surface activation method where special functionalization of the printed AlSi10Mg was performed to assure a uniform catalytic surface yielding a good adhesion of the deposited metal to the substrate. Various methods were used to examine the coating quality, including light microscopy, optical profilometry, XRD, X-ray fluorescence, SEM–energy-dispersive spectroscopy (EDS), focused ion beam (FIB)-SEM, and XPS analyses. The results indicate that the developed coatings yield satisfactory quality, and the suggested surface finishing process can be used for many AM products and applications.

scholarly journals Development of an Additive Manufacturing System for the Deposition of Thermoplastics Impregnated with Carbon Fibers

2019 ◽  
Vol 3 (2) ◽  
pp. 35 ◽  
Author(s):  
Miguel Reis Silva ◽  
António M. Pereira ◽  
Nuno Alves ◽  
Gonçalo Mateus ◽  
Artur Mateus ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Additive Manufacturing ◽  
Carbon Fibers ◽  
Low Cost ◽  
Deposition Process ◽  
Processing Parameters ◽  
Yarn Diameter ◽  
Thermoplastic Matrix ◽  
Anisotropic Mechanical Properties ◽  
Long Carbon Fiber

This work presents an innovative system that allows the oriented deposition of continuous fibers or long fibers, pre-impregnated or not, in a thermoplastic matrix. This system is used in an integrated way with the filamentary fusion additive manufacturing technology and allows a localized and oriented reinforcement of polymer components for advanced engineering applications at a low cost. To demonstrate the capabilities of the developed system, composite components of thermoplastic matrix (polyamide) reinforced with pre-impregnated long carbon fiber (carbon + polyamide), 1 K and 3 K, were processed and their tensile and flexural strength evaluated. It was demonstrated that the tensile strength value depends on the density of carbon fibers present in the composite, and that with the passage of 2 to 4 layers of fibers, an increase in breaking strength was obtained of about 366% and 325% for the 3 K and 1 K yarns, respectively. The increase of the fiber yarn diameter leads to higher values of tensile strength of the composite. The obtained standard deviation reveals that the deposition process gives rise to components with anisotropic mechanical properties and the need to optimize the processing parameters, especially those that lead to an increase in adhesion between deposited layers.

Sign in / Sign up

Export Citation Format

Share Document