Circuit Simulation for Solar Power Maximum Power Point Tracking with Different Buck-Boost Converter Topologies

2014 ◽  
Author(s):  
Jaw-Kuen Shiau ◽  
Min-Yi Lee ◽  
Yu-Chen Wei ◽  
Bo-Chih Chen
Keyword(s):  
Solar Power ◽  
Circuit Simulation ◽  
Maximum Power Point Tracking ◽  
Boost Converter ◽  
Maximum Power ◽  
Maximum Power Point ◽  
Point Tracking ◽  
Power Point Tracking ◽  
Converter Topologies ◽  
Power Point

Implementaasi Maximum Power Point Tracker (MPPT) dengan topologi sepic pada pembangkit listrik tenaga surya

JURNAL ELTEK ◽  
2020 ◽  
Vol 18 (2) ◽  
pp. 1
Author(s):  
Oktriza Melfazen ◽  
M. Taqijuddin Alawiy ◽  
Denda Dewatama
Keyword(s):  
Power Plants ◽  
Solar Power ◽  
Maximum Power Point Tracking ◽  
Average Power ◽  
Maximum Power ◽  
Maximum Power Point ◽  
Point Tracking ◽  
Power Point Tracking ◽  
Arduino Uno ◽  
Power Point

Terdapat rugi-rugi daya dalam proses menghasilkan daya pada Pembangkit Listrik Tenaga Surya (PLTS) konvensional. Sehingga energi yang dihasilkan tidak terserap secara maksimal. Sistem Pembangkit Listrik Tenaga Surya yang didesain dalam penelitian ini diharapkan dapat menghasilkan energi optimal dengan memanfaatkan kemampuan algoritma Maximum Power Point Tracking (MPPT) dengan metode Perturb and Obserb yang diaplikasikan pada topologi SEPIC. Pada penelitian ini, sistem  menggunakan panel surya berjenis amorphous 60W, sensor arus ACS712, sensor tegangan berupa pembagi tegangan dan rangkaian converter dengan topologi SEPIC yang dikontrol mikrokontroler Arduino UNO dengan sistem MPPT. Hasil penelitian yang didapat sebagai berikut: penempatan panel surya yang baik adalah menghadap atas (tegak lurus dengan permukaan bumi, sensor arus bekerja dengan eror rata-rata 1,92%, sensor tegangan mempunyai eror rata-rata 2,76%, dan topologi SEPIC dengan MPPT mempunyai hasil daya rata-rata 26,13 W.   There are power losses in the process of generating power in conventional Solar Power Plants (PLTS). So that the energy produced is not absorbed to the fullest. The Solar Power Sistem designed in this study is expected to produce optimal energy by utilizing the ability of the Maximum Power Point Tracking (MPPT) algorithm with the Perturb and Obserb method applied to the SEPIC topology. The sistem built in this study uses a 60W amorphous type solar panel, ACS712 current sensor, a voltage sensor in the form of a voltage divider and a converter circuit with a SEPIC topology controlled by an Arduino UNO microcontroller with an MPPT sistem.The results obtained as follows: a good placement of solar panels is facing upward (perpendicular to the surface of the earth, current sensors work with an average eror of 1.92%, voltage sensors have an average eror of 2.76%, and SEPIC topology with MPPT has an average power yield of 26.13 W.

scholarly journals Maximum power point tracking of a solar PV array using single stage three phase inverter

2018 ◽  
Vol 7 (2.31) ◽  
pp. 97 ◽  
Author(s):  
M Jayakumar ◽  
V Vanitha ◽  
V Jaisuriya ◽  
M Karthikeyan ◽  
George Daniel ◽  
...  
Keyword(s):  
Solar Power ◽  
Maximum Power Point Tracking ◽  
Maximum Power ◽  
Solar Pv ◽  
Maximum Power Point ◽  
Pv Array ◽  
Point Tracking ◽  
Power Point Tracking ◽  
Three Phase ◽  
Power Point

Solar power is widely available around the globe but efficient transfer of solar power to the load becomes a challenging task. There are various methods in which the power transfer can be done, the following work proposes a method for efficient tracking of solar power.  MPPT [ maximum power point tracking] algorithm applied on three phase voltage source inverter connected to solar PV array with a three phase load. MPPT is applied on inverter rather than conventionally applying MPPT on DC-DC converter. Perturb and Observe method is applied in the MPPT algorithm to find the optimal modulation index for the inverter to transfer maximum power from the panel. Sine pulse width modulation technique is employed for controlling the switching pattern of the inverter. The algorithm is programmed for changing irradiation and temperature condition. The system does not oscillate about the MPP point as the algorithm set the system at MPP and does not vary till a variation in irradiation is sensed.  The proposed system can be installed at all places and will reduce the cost, size and losses compared to conventional system. 

Modelling and Simulation of Boost Converter with Maximum Power Point Tracking (MPPT) for Photovoltaic Application

2014 ◽  
Vol 71 (5) ◽  
Author(s):  
Ahmad Shaharuddin Mat Su, ◽  
Rasli Abd Ghani ◽  
Slamet Slamet
Keyword(s):  
Fuzzy Logic ◽  
Fuzzy Logic Controller ◽  
Maximum Power Point Tracking ◽  
Boost Converter ◽  
Maximum Power ◽  
Maximum Power Point ◽  
Point Tracking ◽  
Power Point Tracking ◽  
Proposed Model ◽  
Power Point

This paper presents the proposed model and simulation of a DC to DC converter with maximum power point tracking (MPPT) using fuzzy logic controller (FLC) for a standalone Photovoltaic (PV) System. This research will focus on the developing high performance DC to DC converter with fuzzy logic controller based to extract the maximum power that generated by the PV panel. The system composed of the PV array and DC-DC boost converter with MPPT system. The maximum power point tracking control is based on adaptive fuzzy logic to control ON/OFF time of IGBT switch of DC-DC boost converter. The proposed DC to DC converter is designed by using the Multisim software while the controller programme will be carried out by using the Matlab Simulink software. Pulse width modulation will be generated by the controller to trigger the IGBT gate. The performance of the proposed model is evaluated by the simulation and the result show that our proposed converter can convert more power from generated voltage. By using the fuzzy logic method to track the maximum power of the PV array, it is faster and the voltage is stable.

Sign in / Sign up

Export Citation Format

Share Document