scholarly journals Numerical Investigation into the Gas Production from Hydrate Deposit under Various Thermal Stimulation Modes in a Multi-Well System in Qilian Mountain

Entropy ◽  
2021 ◽  
Vol 23 (7) ◽  
pp. 800
Author(s):  
Bo Li ◽  
Yuan Ye ◽  
Tingting Zhang ◽  
Qingcui Wan
Keyword(s):  
Water Injection ◽  
Electric Heating ◽  
Gas Production ◽  
External Heat ◽  
Hot Water ◽  
Water Flooding ◽  
Qilian Mountain ◽  
Local Pressure ◽  
Gas Seepage ◽  
Hydrate Deposit

The primary objective of this study was to investigate the energy recovery performance of the permafrost hydrate deposit in the Qilian Mountain at site DK-2 using depressurization combined with thermal injection by the approach of numerical simulation. A novel multi-well system with five horizontal wells was applied for large-scale hydrate mining. The external heat is provided by means of water injection, wellbore heating, or the combinations of them through the central horizontal well, while the fluids are extracted outside from the other four production wells under constant depressurization conditions. The injected water can carry the heat into the hydrate deposit with a faster rate by thermal convection regime, while it also raises the local pressure obviously, which results in a strong prohibition effect on hydrate decomposition in the region close to the central well. The water production rate is always controllable when using the multi-well system. No gas seepage is observed in the reservoir due to the resistance of the undissociated hydrate. Compared with hot water injection, the electric heating combined with normal temperature water flooding basically shows the same promotion effect on gas recovery. Although the hydrate regeneration is more severe in the case of pure electric heating, the external heat can be more efficiently assimilated by gas hydrate, and the efficiency of gas production is best compared with the cases involving water injection. Thus, pure wellbore heating without water injection would be more suitable for hydrate development in deposits characterized by low-permeability conditions.

SS - Gas Hydrate: Gas production from methane hydrate sediment layer by thermal stimulation with hot water injection

2010 ◽  
Author(s):  
Kyuro Sasaki ◽  
Shinzi Ono ◽  
Yuichi Sugai ◽  
Norio Tenma ◽  
Takao Ebinuma ◽  
...  
Keyword(s):  
Gas Hydrate ◽  
Methane Hydrate ◽  
Water Injection ◽  
Gas Production ◽  
Hot Water ◽  
Thermal Stimulation ◽  
Sediment Layer

Nanotechnology Helps Decrease Pressure, Increase Injection in Offshore China Oil Field

2021 ◽  
Vol 73 (09) ◽  
pp. 58-59
Author(s):  
Chris Carpenter
Keyword(s):  
Water Injection ◽  
Injection Pressure ◽  
Gas Production ◽  
Oil Field ◽  
Water Flooding ◽  
Injection System ◽  
Bohai Bay ◽  
Reservoir Properties ◽  
Positive Effects ◽  
Offshore Technology

This article, written by JPT Technology Editor Chris Carpenter, contains highlights of paper OTC 30407, “Case Study of Nanopolysilicon Materials’ Depressurization and Injection-Increasing Technology in Offshore Bohai Bay Oil Field KL21-1,” by Qing Feng, Nan Xiao Li, and Jun Zi Huang, China Oilfield Services, et al., prepared for the 2020 Offshore Technology Conference Asia, originally scheduled to be held in Kuala Lumpur, 2–6 November. The paper has not been peer reviewed. Copyright 2020 Offshore Technology Conference. Reproduced by permission. Nanotechnology offers creative approaches to solve problems of oil and gas production that also provide potential for pressure-decreasing application in oil fields. However, at the time of writing, successful pressure-decreasing nanotechnology has rarely been reported. The complete paper reports nanopolysilicon as a new depressurization and injection-increasing agent. The stability of nanopolysilicon was studied in the presence of various ions, including sodium (Na+), calcium (Ca2+), and magnesium (Mg2+). The study found that the addition of nanomaterials can improve porosity and permeability of porous media. Introduction More than 600 water-injection wells exist in Bohai Bay, China. Offshore Field KL21-1, developed by water-flooding, is confronted with the following challenges: - Rapid increase and reduction of water-injection pressure - Weak water-injection capacity of reservoir - Decline of oil production - Poor reservoir properties - Serious hydration and expansion effects of clay minerals To overcome injection difficulties in offshore fields, conventional acidizing measures usually are taken. But, after multiple cycles of acidification, the amount of soluble substances in the rock gradually decreases and injection performance is shortened. Through injection-performance experiments, it can be determined that the biological nanopolysilicon colloid has positive effects on pressure reduction and injection increase. Fluid-seepage-resistance decreases, the injection rate increases by 40%, and injection pressure decreases by 10%. Features of Biological Nanopolysilicon Systems The biological nanopolysilicon-injection system was composed of a bioemulsifier (CDL32), a biological dispersant (DS2), and a nanopolysilicon hydrophobic system (NP12). The bacterial strain of CDL32 was used to obtain the culture colloid of biological emulsifier at 37°C for 5 days. DS2 was made from biological emulsifier CDL32 and some industrial raw materials described in Table 1 of the complete paper. Nanopolysilicon hydrophobic system NP12 was composed of silicon dioxide particles. The hydrophobic nanopolysilicons selected in this project featured particle sizes of less than 100 nm. In the original samples, a floc of nanopolysilicon was fluffy and uniform. But, when wet, nanopolysilicon will self-aggregate and its particle size increases greatly. At the same time, nanopolysilicon features significant agglomeration in water. Because of its high interface energy, nanopolysilicon is easily agglomerated, as shown in Fig. 1.

scholarly journals Experimental Investigation on Oil Enhancement Mechanism of Hot Water Injection in tight reservoirs

Open Physics ◽  
2016 ◽  
Vol 14 (1) ◽  
pp. 703-713 ◽  
Author(s):  
Hao Yongmao ◽  
Lu Mingjing ◽  
Dong Chengshun ◽  
Jia Jianpeng ◽  
Su Yuliang ◽  
...  
Keyword(s):  
Oil Recovery ◽  
Water Saturation ◽  
Water Injection ◽  
Hot Water ◽  
Water Flooding ◽  
Water Displacement ◽  
Pore Characteristics ◽  
Irreducible Water Saturation ◽  
Tight Reservoirs ◽  
Oil Water

AbstractAimed at enhancing the oil recovery of tight reservoirs, the mechanism of hot water flooding was studied in this paper. Experiments were conducted to investigate the influence of hot water injection on oil properties, and the interaction between rock and fluid, petrophysical property of the reservoirs. Results show that with the injected water temperature increasing, the oil/water viscosity ratio falls slightly in a tight reservoir which has little effect on oil recovery. Further it shows that the volume factor of oil increases significantly which can increase the formation energy and thus raise the formation pressure. At the same time, oil/water interfacial tension decreases slightly which has a positive effect on production though the reduction is not obvious. Meanwhile, the irreducible water saturation and the residual oil saturation are both reduced, the common percolation area of two phases is widened and the general shape of the curve improves. The threshold pressure gradient that crude oil starts to flow also decreases. It relates the power function to the temperature, which means it will be easier for oil production and water injection. Further the pore characteristics of reservoir rocks improves which leads to better water displacement. Based on the experimental results and influence of temperature on different aspects of hot water injection, the flow velocity expression of two-phase of oil and water after hot water injection in tight reservoirs is obtained.

Gas Production System From Methane Hydrate Layers by Hot Water Injection Using Dual Horizontal Wells

2009 ◽  
Vol 48 (10) ◽  
pp. 21-26 ◽  
Author(s):  
K. Sasaki ◽  
S. Ono ◽  
Y. Sugai ◽  
T. Ebinuma ◽  
H. Narita ◽  
...  
Keyword(s):  
Production System ◽  
Methane Hydrate ◽  
Water Injection ◽  
Horizontal Wells ◽  
Gas Production ◽  
Hot Water

A Thermal Gas Production System from Methane Hydrate Layers by Hot Water Injection

2010 ◽  
Author(s):  
Kyuro Sasaki ◽  
Shinzi Ono ◽  
Yuichi Sugai ◽  
Norio Tenma ◽  
Takao Ebinuma ◽  
...  
Keyword(s):  
Production System ◽  
Methane Hydrate ◽  
Water Injection ◽  
Gas Production ◽  
Hot Water
Sign in / Sign up

Export Citation Format

Share Document