scholarly journals Effects of Al Addition on Microstructures and Mechanical Properties of CoCrFeMnNiAlx High Entropy Alloy Films

Entropy ◽  
2019 ◽  
Vol 22 (1) ◽  
pp. 2 ◽  
Author(s):  
Ya-Chu Hsu ◽  
Chia-Lin Li ◽  
Chun-Hway Hsueh
Keyword(s):  
Mechanical Properties ◽  
Compressive Yield Strength ◽  
High Entropy Alloy ◽  
Face Centered Cubic ◽  
Alloy Films ◽  
High Entropy ◽  
Al Content ◽  
Microstructures And Mechanical Properties ◽  
Fcc Phase ◽  
Bcc Phase

CoCrFeMnNiAlx (x = 0, 0.07, 0.3, 0.6, 1.0, 1.3) high-entropy alloy films (HEAFs) were processed by co-sputtering of CoCrFeMnNi alloy and Al targets. The effects of Al content on the microstructures and mechanical properties of HEAFs were studied. The XRD results indicated that the crystalline structure changed from the single face-centered cubic (FCC) phase for x = 0 and 0.07 to duplex FCC + body-centered cubic (BCC) phases for x = 0.3 and 0.6, and eventually, to a single BCC phase for x = 1.0 and 1.3, which agreed with the corresponding selected-area electron diffraction patterns. Also, nanotwins were observed in the FCC phase. Mechanical properties of films were studied using nanoindentation and micropillar compression tests. The hardness increased from 5.71 GPa at x = 0 to 8.74 GPa at x = 1.3. The compressive yield strength increased from 1.59 GPa to 3.73 GPa; however, the fracture strain decreased from 20.91% (no fracture) to 13.78% with the increasing Al content. Both nanotwins and BCC phase contributed to the strengthening effects for CoCrFeMnNiAlx HEAFs. Also, compared to the bulk CoCrFeMnNiAlx counterpart, the film exhibited much higher hardness and strength because of the much smaller grain size and the presence of nanotwins.

scholarly journals Effects of Nb Addition on Microstructures and Mechanical Properties of Nbx-CoCrFeMnNi High Entropy Alloy Films

Coatings ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 1539
Author(s):  
Yu-Hsuan Liang ◽  
Chia-Lin Li ◽  
Chun-Hway Hsueh
Keyword(s):  
Mechanical Properties ◽  
Amorphous Phase ◽  
Compressive Yield Strength ◽  
High Entropy Alloy ◽  
Face Centered Cubic ◽  
Compression Tests ◽  
Alloy Films ◽  
High Entropy ◽  
Microstructures And Mechanical Properties ◽  
Nb Addition

In the present work, Nbx-CoCrFeMnNi high entropy alloy films (HEAFs, 0 to 7.2 at.% Nb) were fabricated by radio frequency (RF) magnetron co-sputtering of CoCrFeMnNi alloy and Nb targets. The effects of Nb addition on the microstructures and mechanical properties of HEAFs were systematically investigated. For Nb-free film (0 at.% Nb), the face-centered cubic (FCC) peaks were identified in the X-ray diffraction (XRD) pattern. The addition of Nb resulted in a broadening of diffraction peaks, a decrease in peak intensity, and the vanishment of high-angle peaks. Transmission electron microscope (TEM) images indicated the formation of nanotwins at low Nb concentrations, and a transition from a single phase FCC solid solution to an amorphous phase was observed with the increasing Nb concentration. The films were strengthened with an increase in Nb concentration. Specifically, the hardness characterized by nanoindentation increased from 6.5 to 8.1 GPa. The compressive yield strength and fracture strength measured from micropillar compression tests were improved from 1.08 GPs and 2.56 GPa to 2.70 GPa and 5.76 GPa, respectively, whereas the fracture strain decreased from >29.4% (no fracture) to 15.8%. Additionally, shear banding was observed in the presence of amorphous phase.

scholarly journals Effects of Cr Content on Microstructure and Mechanical Properties of AlCoCrxFeNi High-Entropy Alloy

2018 ◽  
Vol 2018 ◽  
pp. 1-7 ◽  
Author(s):  
Tao-Tsung Shun ◽  
Wei-Jhe Hung
Keyword(s):  
Mechanical Properties ◽  
Molar Ratio ◽  
High Entropy Alloy ◽  
High Entropy ◽  
Cr Content ◽  
Microstructure And Mechanical Properties ◽  
Alloy Hardness ◽  
Fcc Phase ◽  
Bcc Phase ◽  
Feni Alloys

In this study, we investigated the effects of Cr content on the crystal structure, microstructure, and mechanical properties of four AlCoCrxFeNi (x = 0.3, 0.5, 0.7, and 1.0, in molar ratio) high-entropy alloys. AlCoCr0.3FeNi alloy contains duplex phases, which are ordered BCC phase and FCC phase. As the Cr content increases to x = 1.0, the FCC phase disappears and the microstructure exhibits a spinodal structure formed by a BCC phase and an ordered BCC phase. This result indicates that Cr is a BCC former in AlCoCrxFeNi alloys. With increasing Cr content, the alloy hardness increases from HV415 to HV498. AlCoCr0.3FeNi, AlCoCr0.5FeNi, and AlCoCr0.7FeNi exhibit a high compressive fracture strain of about 0.24 because of the formation of the FCC phase in the BCC matrix. Moreover, the highest yield stress of 1394 MPa and compressive strength of 1841 MPa presented by AlCoCrFeNi alloy are due to the existence of a nano-net-like spinodal structure.

Microstructures and mechanical properties of CoCrFeMnNiV high entropy alloy films

2020 ◽  
Vol 820 ◽  
pp. 153388 ◽  
Author(s):  
Shuang Fang ◽  
Cheng Wang ◽  
Chia-Lin Li ◽  
Jun-Hua Luan ◽  
Zeng-Bao Jiao ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Entropy Alloy ◽  
Alloy Films ◽  
High Entropy ◽  
Microstructures And Mechanical Properties

scholarly journals Phase Evolution, Microstructure and Mechanical Property of AlCoCrFeNiTi High-Entropy Alloy Coatings Prepared by Mechanical Alloying and Laser Cladding

Metals ◽  
2019 ◽  
Vol 9 (10) ◽  
pp. 1036
Author(s):  
Weijie Yu ◽  
Yun Wang ◽  
Ruitao Li ◽  
Junhong Mao
Keyword(s):  
Mechanical Alloying ◽  
Laser Cladding ◽  
Steel Substrate ◽  
Phase Evolution ◽  
High Entropy Alloy ◽  
Second Phase ◽  
Face Centered Cubic ◽  
High Entropy ◽  
Fcc Phase ◽  
Bcc Phase

AlCoCrFeNiTi high-entropy alloy coatings (HEACs) were prepared by mechanical alloying (MA) and laser cladding (LC) process on H13 hot-working die steel substrate. Phase evolution, microstructure, and mechanical properties of the alloyed powder and HEACs were investigated in detail. The final milling AlCoCrFeNiTi coating powders exhibited simple body centered cubic (BCC) phase and mean granular size of less than 4 μm. With the increase of heat input of the laser, partial BCC phase transformed into minor face centered cubic (FCC) phase during LC. AlCoCrFeNiTi HEACs showed excellent metallurgical bonding with the substrate, and few defects. Moreover, the microhardness of AlCoCrFeNiTi HEACs reached 1069 HV due to the existence of the hard oxidation and the second phase grains, which are about five times that of the substrate. The laser surface cladding HEACs exhibited deteriorated tensile property compared with that of the substrate and the fracture generally occurred in the region of HEACs. The fracture mechanism of AlCoCrFeNiTi HEACs was dominated by the comprehensive influence of brittle fracture and ductile fracture.

scholarly journals Nanoporous Quasi-High-Entropy Alloy Microspheres

Metals ◽  
2019 ◽  
Vol 9 (3) ◽  
pp. 345 ◽  
Author(s):  
Lianzan Yang ◽  
Yongyan Li ◽  
Zhifeng Wang ◽  
Weimin Zhao ◽  
Chunling Qin
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
High Specific Surface Area ◽  
High Entropy Alloy ◽  
Face Centered Cubic ◽  
High Entropy ◽  
Hierarchical Porous

High-entropy alloys (HEAs) present excellent mechanical properties. However, the exploitation of chemical properties of HEAs is far less than that of mechanical properties, which is mainly limited by the low specific surface area of HEAs synthesized by traditional methods. Thus, it is vital to develop new routes to fabricate HEAs with novel three-dimensional structures and a high specific surface area. Herein, we develop a facile approach to fabricate nanoporous noble metal quasi-HEA microspheres by melt-spinning and dealloying. The as-obtained nanoporous Cu30Au23Pt22Pd25 quasi-HEA microspheres present a hierarchical porous structure with a high specific surface area of 69.5 m2/g and a multiphase approximatively componential solid solution characteristic with a broad single-group face-centered cubic XRD pattern, which is different from the traditional single-phase or two-phase solid solution HEAs. To differentiate, these are named quasi-HEAs. The synthetic strategy proposed in this paper opens the door for the synthesis of porous quasi-HEAs related materials, and is expected to promote further applications of quasi-HEAs in various chemical fields.

Phase Transition of As-Milled and Annealed CrCuFeMnNi High-Entropy Alloy Powder

NANO ◽  
2018 ◽  
Vol 13 (09) ◽  
pp. 1850100 ◽  
Author(s):  
Rui-Feng Zhao ◽  
Bo Ren ◽  
Guo-Peng Zhang ◽  
Zhong-Xia Liu ◽  
Jian-Jian Zhang
Keyword(s):  
Phase Transition ◽  
Solution Structure ◽  
Milling Time ◽  
Structure Evolution ◽  
High Entropy Alloy ◽  
Chemical Homogeneity ◽  
High Entropy ◽  
Dynamic Phase Transition ◽  
Fcc Phase ◽  
Bcc Phase

The CrCuFeMnNi high entropy alloy (HEA) powder was synthesized by mechanical alloying. The effects of milling time and subsequent annealing on the structure evolution, thermostability and magnetic property were investigated. After 50[Formula: see text]h of milling, the CrCuFeMnNi HEA powder consisted of a major FCC phase and a small amount of BCC phase. The crystallite size and strain lattice of 50[Formula: see text]h-ball-milled CrCuFeMnNi HEA powder were 12[Formula: see text]nm and 1.02%, respectively. The powder exhibited refined morphology and excellent chemical homogeneity. The supersaturated solid solution structure of the as-milled HEA powder transformed into FCC1, FCC2, a small amount of BCC and [Formula: see text] phase in annealed state. Most of the BCC phase decomposed into FCC (mainly FCC2 phase) and [Formula: see text] phases, and the dynamic phase transition was almost in equilibrium at 900[Formula: see text]C. The saturated magnetization and coercivity force of the 50[Formula: see text]h-ball-milled CrCuFeMnNi HEA powder were respectively 16.1[Formula: see text]emu/g and 56.2[Formula: see text]Oe.

scholarly journals Dynamic Mechanical Properties and Microstructure of an (Al0.5CoCrFeNi)0.95Mo0.025C0.025 High Entropy Alloy

Entropy ◽  
2019 ◽  
Vol 21 (12) ◽  
pp. 1154
Author(s):  
Bingfeng Wang ◽  
Chu Wang ◽  
Bin Liu ◽  
Xiaoyong Zhang
Keyword(s):  
Mechanical Properties ◽  
Shear Band ◽  
High Strain Rate ◽  
Strain Rate ◽  
High Strain ◽  
Dynamic Mechanical Properties ◽  
High Entropy Alloy ◽  
Face Centered Cubic ◽  
High Entropy ◽  
Dynamic Mechanical

The dynamic mechanical properties and microstructure of the (Al0.5CoCrFeNi)0.95Mo0.025C0.025 high entropy alloy (HEA) prepared by powder extrusion were investigated by a split Hopkinson pressure bar and electron probe microanalyzer and scanning electron microscope. The (Al0.5CoCrFeNi)0.95Mo0.025C0.025 HEA has a uniform face-centered cubic plus body-centered cubic solid solution structure and a fine grain-sized microstructure with a size of about 2 microns. The HEA possesses an excellent strain hardening rate and high strain rate sensitivity at a high strain rate. The Johnson–Cook plastic model was used to describe the dynamic flow behavior. Hat-shaped specimens with different nominal strain levels were used to investigate forced shear localization. After dynamic deformation, a thin and short shear band was generated in the designed shear zone and then the specimen quickly fractured along the shear band.

Sign in / Sign up

Export Citation Format

Share Document