scholarly journals Fluid Flow and Entropy Generation Analysis of Al2O3–Water Nanofluid in Microchannel Plate Fin Heat Sinks

Entropy ◽  
2019 ◽  
Vol 21 (8) ◽  
pp. 739 ◽  
Author(s):  
Hao Ma ◽  
Zhipeng Duan ◽  
Liangbin Su ◽  
Xiaoru Ning ◽  
Jiao Bai ◽  
...  
Keyword(s):  
Reynolds Number ◽  
Pressure Drop ◽  
Aspect Ratio ◽  
Entropy Generation ◽  
Volume Fraction ◽  
Microchannel Plate ◽  
Heat Sinks ◽  
Entropy Generation Rate ◽  
Nanoparticle Volume Fraction ◽  
Channel Aspect Ratio

The flow in channels of microdevices is usually in the developing regime. Three-dimensional laminar flow characteristics of a nanofluid in microchannel plate fin heat sinks are investigated numerically in this paper. Deionized water and Al2O3–water nanofluid are employed as the cooling fluid in our work. The effects of the Reynolds number (100 < Re < 1000), channel aspect ratio (0 < ε < 1), and nanoparticle volume fraction (0.5% < Φ < 5%) on pressure drop and entropy generation in microchannel plate fin heat sinks are examined in detail. Herein, the general expression of the entropy generation rate considering entrance effects is developed. The results revealed that the frictional entropy generation and pressure drop increase as nanoparticle volume fraction and Reynolds number increase, while decrease as the channel aspect ratio increases. When the nanoparticle volume fraction increases from 0 to 3% at Re = 500, the pressure drop of microchannel plate fin heat sinks with ε = 0.5 increases by 9%. It is demonstrated that the effect of the entrance region is crucial for evaluating the performance of microchannel plate fin heat sinks. The study may shed some light on the design and optimization of microchannel heat sinks.

The Role of Fin Geometry in Heat Sink Performance

2006 ◽  
Vol 128 (4) ◽  
pp. 324-330 ◽  
Author(s):  
W. A. Khan ◽  
J. R. Culham ◽  
M. M. Yovanovich
Keyword(s):  
Reynolds Number ◽  
Aspect Ratio ◽  
Entropy Generation ◽  
Heat Sink ◽  
Control Volume ◽  
Generation Rate ◽  
Heat Transfer Fluid ◽  
Entropy Generation Rate ◽  
Minimum Entropy ◽  
Axis Ratio

The following study will examine the effect on overall thermal/fluid performance associated with different fin geometries, including, rectangular plate fins as well as square, circular, and elliptical pin fins. The use of entropy generation minimization, EGM, allows the combined effect of thermal resistance and pressure drop to be assessed through the simultaneous interaction with the heat sink. A general dimensionless expression for the entropy generation rate is obtained by considering a control volume around the pin fin including base plate and applying the conservations equations for mass and energy with the entropy balance. The formulation for the dimensionless entropy generation rate is developed in terms of dimensionless variables, including the aspect ratio, Reynolds number, Nusselt number, and the drag coefficient. Selected fin geometries are examined for the heat transfer, fluid friction, and the minimum entropy generation rate corresponding to different parameters including axis ratio, aspect ratio, and Reynolds number. The results clearly indicate that the preferred fin profile is very dependent on these parameters.

scholarly journals Analytical and numerical study of entropy generation in small scale heat exchangers

2019 ◽  
Author(s):  
Mahyar Pourghasemi
Keyword(s):  
Reynolds Number ◽  
Pressure Drop ◽  
Energy Harvesting ◽  
Aspect Ratio ◽  
Entropy Generation ◽  
Heat Sink ◽  
Optimum Operating ◽  
Maximum Pressure ◽  
Channel Height ◽  
Maximum Pressure Drop

In present work, the entropy generation minimization technique (EGM) is applied to study the performance of a microchannel heat sink combined with a new proposed parameter called irreversibility index and energy harvesting concept. Three different cases have been investigated using geometry of a microchanel heat sink selected from experimental work in the literature. The constraints considered in this study, are fixed channel height and maximum pressure drop. It has been observed that with fixed channel height constraint, while the aspect ratio changes from 1 to 10, the optimum operating condition fall in the range of Reynolds number equal to 2000 and aspect ratio of 2.25. Moreover, the extra constrain on maximum pressure drop imposes a limitation on applicable aspect ratio range. The maximum aspect ratio of the channel for stable flow field in this case cannot be higher than 5 imposed by criteria of laminar flow regime. The obtained optimum values are Reynolds number of 1850 and aspect ratio of 2. Using a combined new defined irreversibility index and Energy Harvesting Concept (EHC), it has been shown that the optimum design values for industrial applications are not necessary ones obtained from EGM method and may shift to a new operating point based on the method considered for energy harvesting.

Optimization of Pin-Fin Heat Sinks in Bypass Flow Using Entropy Generation Minimization Method

2008 ◽  
Vol 130 (3) ◽  
Author(s):  
W. A. Khan ◽  
J. R. Culham ◽  
M. M. Yovanovich
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Entropy Generation ◽  
Heat Sink ◽  
Heat Sinks ◽  
Entropy Generation Rate ◽  
Bypass Flow ◽  
Minimization Method ◽  
Pin Fin ◽  
Entropy Generation Minimization

An entropy generation minimization method is applied to study the thermodynamic losses caused by heat transfer and pressure drop for the fluid in a cylindrical pin-fin heat sink and bypass flow regions. A general expression for the entropy generation rate is obtained by considering control volumes around the heat sink and bypass regions. The conservation equations for mass and energy with the entropy balance are applied in both regions. Inside the heat sink, analytical/empirical correlations are used for heat transfer coefficients and friction factors, where the reference velocity used in the Reynolds number and the pressure drop is based on the minimum free area available for the fluid flow. In bypass regions theoretical models, based on laws of conservation of mass, momentum, and energy, are used to predict flow velocity and pressure drop. Both in-line and staggered arrangements are studied and their relative performance is compared to the same thermal and hydraulic conditions. A parametric study is also performed to show the effects of bypass on the overall performance of heat sinks.

Numerical Analysis of Entropy Generation in Array of Pin-Fin Heat Sinks for Some Different Geometries

2010 ◽  
Author(s):  
Reza Kamali ◽  
Bamdad Barari ◽  
Ashkan Abbasian Shirazi
Keyword(s):  
Heat Transfer ◽  
Numerical Analysis ◽  
Pressure Drop ◽  
Cross Section ◽  
Entropy Generation ◽  
Heat Sink ◽  
Control Volume ◽  
Heat Sinks ◽  
Entropy Generation Rate ◽  
Pin Fin

In this study, Numerical analysis has been used to investigate entropy generation for array of pin-fin heat sink. Technique is applied to study the thermodynamic losses caused by heat transfer and pressure drop in pin-fin heat sinks. A general expression for the entropy generation rate is obtained by considering the whole heat sink as a control volume and applying the conservation equations for mass and energy with the entropy balance. Analytical and empirical correlations for heat transfer coefficients and friction factors are used in the numerical modeling. Also effects of heat transfer and pressure drop in entropy generation in control volume over pin-fins have been studied. Numerical analysis has been used for three different models of pin-fin heat sinks. The models are different in cross section area. These cross section areas are circle, horizontal ellipse and vertical ellipse which mentioned in next sections. Reference velocity used in Reynolds number and pressure drop is based on the minimum free area available for the fluid flow. Also for numerical analysis in-line arrangement of fins has been investigated and their relative performance is compared. At the end, the performance of these three models has been compared.

Performance Augmentation and Optimization of Aluminum Oxide-Water Nanofluid Flow in a Two-Fluid Microchannel Heat Exchanger

2013 ◽  
Vol 136 (2) ◽  
Author(s):  
Shahabeddin K. Mohammadian ◽  
Hamid Reza Seyf ◽  
Yuwen Zhang
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Exchanger ◽  
Entropy Generation ◽  
Volume Fraction ◽  
Entropy Generation Rate ◽  
Transfer Model ◽  
Pumping Power ◽  
Volume Fractions ◽  
Microchannel Heat Exchanger

In this paper, laminar forced convection and entropy generation in a counter flow microchannel heat exchanger (CFMCHE) with two different working fluids in hot and cold channels, i.e., pure water and Al2O3–water nanofluid are investigated numerically using a three-dimensional conjugate heat transfer model. The temperature distribution, effectiveness, pumping power and performance index for various volume fractions between 0.01–0.04, three nanoparticles diameters, i.e., 29, 38.4, and 47 nm and a range of Reynolds number from 120 to 480 are given and discussed. According to second law of thermodynamics and entropy generation rate in the CFMCHE, the analysis of optimal volume fraction, particles size, Reynolds number as well as optimal placement of using nanoparticles in hot/cold channels is carried out. It is found that decreasing particles size and increasing nanoparticles concentration lead to higher effectiveness and pumping power as well as lower temperature in the solid phase of CFMCHE. Furthermore, the frictional contribution of entropy increases with decreasing particles size and increasing volume fractions while the trends for heat transfer contribution of entropy are reverse. Total entropy decreases as particles size decreases and volume fraction increases hence the maximum performance occurred at lower particles sizes and higher volume fractions. The Reynolds number has significant effect on performance of system and with decreasing it the effectiveness increases and heat transfer contribution of entropy decreases while the pumping power and frictional contribution of entropy decrease. Finally, it is seen that the capability of heat transfer of Al2O3–water nanofluids is higher when they are under heating conditions because the effectiveness of CFMCHE is higher when nanoparticles are used in cold channels.

Entropy Generation in Microchannels With Two-Phase Flow

2011 ◽  
Author(s):  
A. Nouri-Borujerdi
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Aspect Ratio ◽  
Heat Transfer Rate ◽  
Entropy Generation ◽  
Transfer Rate ◽  
Second Law Of Thermodynamics ◽  
Entropy Generation Rate ◽  
Two Phase ◽  
Overall Performance

The second law of thermodynamics is used to optimize microchannels sizes in two-phase flows. The overall performance of microchannels has been considered. The numerical solution of the conservation equations provides pressure drop and heat transfer rate. There is an aspect ratio which generates the lowest entropy generation rate. It indicates that decreasing the aspect ratio contributes to the reduction of entropy generation by heat transfer, because smaller channel width allows for less heat transfer rate. In contrast, decreasing the aspect ratio contributes the pressure drop increases and more entropy generation is produced. The results also show that, the lowest entropy generation moves towards the higher aspect ratio when the wall heat flux or vapor quality increases.

Optimization of Pin-Fin Heat Sinks in Bypass Flow Using Entropy Generation Minimization Method

2007 ◽  
Author(s):  
Waqar A. Khan ◽  
Michael M. Yovanovich
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Entropy Generation ◽  
Heat Sink ◽  
Heat Sinks ◽  
Entropy Generation Rate ◽  
Bypass Flow ◽  
Minimization Method ◽  
Pin Fin ◽  
Entropy Generation Minimization

An entropy generation minimization, EGM, method is applied to study the thermodynamic losses caused by heat transfer and pressure drop for the fluid in a cylindrical pin-fin heat sink and bypass flow regions. A general expression for the entropy generation rate is obtained by considering control volumes around heat sink and bypass regions. The conservation equations for mass and energy with the entropy balance are applied in both regions. Inside the heat sink, analytical/empirical correlations are used for heat transfer coefficients and friction factors, where the reference velocity used in Reynolds number and pressure drop is based on the minimum free area available for the fluid flow. In bypass regions theoretical models, based on laws of conservation of mass, momentum and energy, are used to predict flow velocity and pressure drop. Both in-line and staggered arrangements are studied and their relative performance is compared for the same thermal and hydraulic conditions. A parametric study is also performed to show the effects of bypass on the overall performance of heat sinks.

Entropy generation and heat transfer analysis for ferrofluid flow between two rotating disks with variable conductivity

2021 ◽  
pp. 095440622199118
Author(s):  
Anupam Bhandari
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Differential Equations ◽  
Entropy Generation ◽  
Heat Transfer Analysis ◽  
Entropy Generation Rate ◽  
Geometrical Parameters ◽  
Rotating Disks ◽  
Coupled Differential Equations ◽  
Lower Disk

Present model analyze the flow and heat transfer of water-based carbon nanotubes (CNTs) [Formula: see text] ferrofluid flow between two radially stretchable rotating disks in the presence of a uniform magnetic field. A study for entropy generation analysis is carried out to measure the irreversibility of the system. Using similarity transformation, the governing equations in the model are transformed into a set of nonlinear coupled differential equations in non-dimensional form. The nonlinear coupled differential equations are solved numerically through the finite element method. Variable viscosity, variable thermal conductivity, thermal radiation, and volume concentration have a crucial role in heat transfer enhancement. The results for the entropy generation rate, velocity distributions, and temperature distribution are graphically presented in the presence of physical and geometrical parameters of the flow. Increasing the values of ferromagnetic interaction number, Reynolds number, and temperature-dependent viscosity enhances the skin friction coefficients on the surface and wall of the lower disk. The local heat transfer rate near the lower disk is reduced in the presence of Harman number, Reynolds number, and Prandtl number. The ferrohydrodynamic flow between two rotating disks might be useful to optimize the use of hybrid nanofluid for liquid seals in rotating machinery.

scholarly journals Entropy generation of a hybrid nanofluid on MHD mixed convection is a lid-driven cavity with partial heating having two rounded corners

2021 ◽  
Vol 321 ◽  
pp. 02004
Author(s):  
Zakaria Korei ◽  
Smail Benissaad
Keyword(s):  
Thermal Conductivity ◽  
Reynolds Number ◽  
Mixed Convection ◽  
Entropy Generation ◽  
Volume Fraction ◽  
Object Oriented ◽  
Reynolds Numbers ◽  
Hybrid Nanofluid ◽  
Driven Cavity ◽  
Partial Heating

This research aims to investigate thermal and flow behaviors and entropy generation of magnetohydrodynamic Al2O3-Cu/water hybrid nanofluid in a lid-driven cavity having two rounded corners. A solver based on C ++ object-oriented language was developed where the finite volume was used. Parameter’s analysis is provided by varying Reynolds numbers (Re), Hartmann numbers (Ha), the volume fraction of hybrid nanofluid (ϕ), radii of the rounded corners. The findings show that reducing the radii of the rounded corners minimizes the irreversibility. Furthermore, the thermal conductivity and dynamic viscosity of hybrid nanofluid contribute to increasing the irreversibility. Finally, the entropy generation is decreased by increasing the Hartman number and increases by rising the Reynolds number.

Thermodynamic optimization of nanofluid flow over a non-isothermal wedge with nonlinear radiation and activation energy

2021 ◽  
Author(s):  
M R Acharya ◽  
P Mishra ◽  
Satyananda Panda
Keyword(s):  
Heat Transfer ◽  
Activation Energy ◽  
Reynolds Number ◽  
Entropy Generation ◽  
Volume Fraction ◽  
Mathematical Formulation ◽  
Bejan Number ◽  
Nanofluid Flow ◽  
Entropy Generation Number ◽  
Generation Number

Abstract This paper analyses the augmentation entropy generation number for a viscous nanofluid flow over a non-isothermal wedge including the effects of non-linear radiation and activation energy. We discuss the influence of thermodynamically important parameters during the study, namely, the Bejan number, entropy generation number, and the augmentation entropy generation number. The mathematical formulation for thermal conductivity and viscosity of nanofluid for Al2O3 − EG mixture has been considered. The results were numerically computed using implicit Keller-Box method and depicted graphically. The important result is the change in augmentation entropy generation number with Reynolds number. We observed that adding nanoparticles (volume fraction) tend to enhance augmentation entropy generation number for Al2O3 − EG nanofluid. Further, the investigation on the thermodynamic performance of non-isothermal nanofluid flow over a wedge reveals that adding nanoparticles to the base fluid is effective only when the contribution of heat transfer irreversibility is more than fluid friction irreversibility. This work also discusses the physical interpretation of heat transfer irreversibility and pressure drop irreversibility. This dependency includes Reynolds number and volume fraction parameter. Other than these, the research looked at a variety of physical characteristics associated with the flow of fluid, heat and mass transfer.

Sign in / Sign up

Export Citation Format

Share Document