scholarly journals Exergy Analysis of Directional Solvent Extraction Desalination Process

Entropy ◽  
2019 ◽  
Vol 21 (3) ◽  
pp. 321 ◽  
Author(s):  
Sorour Alotaibi ◽  
Osama Ibrahim ◽  
Yu Wang ◽  
Tengfei Luo
Keyword(s):  
Solvent Extraction ◽  
Parametric Study ◽  
Octanoic Acid ◽  
Exergy Analysis ◽  
Small Variation ◽  
Water Yield ◽  
Low Grade ◽  
Design Variables ◽  
Exergy Consumption ◽  
The Impact

This paper presents an exergy analysis to evaluate the performance of a continuous directional solvent extraction (DSE) desalination process using octanoic acid. The flow of exergy was calculated for each thermodynamic state and balanced for different components of the system to quantify the inefficiencies in the process. A parametric study was performed to evaluate the impact of three critical design variables on exergy consumption. The parametric study reveals that the total exergy input decreases significantly with an increase in heat exchanger effectiveness. The results also indicate that the heat exchangers account for the highest exergy destruction. The total exergy consumption, however, has a slightly declining trend as the recovery-ratio increases. There is a small variation in the total exergy consumption, within the uncertainty of the calculation, as the highest process temperature increases. When compared to conventional desalination processes, the exergy consumption of the DSE, with heat recovery of 90%, is comparable to those of multi-stage flashing (MSF), but much higher than reverse osmosis (RO). Octanoic acid, which has low product water yield, is identified as the primary factor negatively impacting the exergy consumptions. To exploit the low-grade and low-temperature heat source feature of the DSE process, directional solvents with higher yield should be identified or designed to enable its full implementation.

Strength and Fatigue Performance of Steel Lazy Wave Risers With Change in Configuration Parameters

2019 ◽  
Author(s):  
Mayank Lal ◽  
Feng Wang ◽  
Xiaohua Lu ◽  
Abhilash Sebastian
Keyword(s):  
Deep Water ◽  
Parametric Study ◽  
Fatigue Performance ◽  
Design Criteria ◽  
Cost Assessment ◽  
Fatigue Design ◽  
Design Variables ◽  
Steel Catenary Risers ◽  
Normative Cost ◽  
The Impact

Abstract Steel Lazy wave risers are being increasingly used for deep water applications due to better strength and fatigue performance in the touchdown zone compared to steel catenary risers. Several parameters govern the design of steel lazy wave risers including the length of the catenary from hang-off to start of buoyancy section and the length of the buoyancy section. In this paper, a parametric study is performed to investigate the trends in strength and fatigue performance of steel lazy wave risers with change in configuration parameters. A normative cost assessment is also performed to show the impact of these design variables on overall cost of the system. Dynamic analysis is performed to check the change in strength and fatigue performance of steel lazy wave risers as the configuration parameters are changed. The results from the parametric study will assist in designing steel lazy wave risers which satisfy the strength and fatigue design criteria.

Robust Suspension System Design

1993 ◽  
Author(s):  
John E. Beard ◽  
John W. Sutherland
Keyword(s):  
System Design ◽  
Robust Design ◽  
Loss Function ◽  
Kinematic Model ◽  
Small Variation ◽  
Suspension System ◽  
Product Performance ◽  
Design Variables ◽  
Manufacturing Assembly ◽  
The Impact

Abstract Traditionally, levels for design variables are sought that produce optimal performance of a product. When manufacturing and assembly processes are used to realize the design intent, however, the product performance may differ from that envisioned during design. This is because the performance of a product is often very sensitive to manufacturing and assembly variations. This paper presents a methodology for robust design that incorporates the impact of manufacturing/assembly variations. The methodology characterizes the performance of a manufactured product via a loss function. The loss function measure is attractive from a robust design standpoint since it stresses both desirable performance on the average and small variation in performance from product to product. The design methodology is demonstrated through a suspension system design application. A model for the kinematic behavior of a suspension system is developed. The scrub rate is selected as the response of interest to demonstrate the methodology. The behavior of the kinematic model, in terms of the loss function, is approximated near a set point and levels of the design variables are sought that minimize the loss. An iterative procedure is described for optimizing the loss function. The application demonstrates that substantial improvements can be made in terms of actual manufactured product performance through the use of the methodology.

A Fracture Mechanics Based Parametric Study of the Copper-to-Copper Direct Thermo-Compression Bonded Interface Using Finite Element Method

2013 ◽  
Author(s):  
Ah-Young Park ◽  
Satish Chaparala ◽  
Seungbae Park
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Parametric Study ◽  
Initial Crack ◽  
Bonding Interface ◽  
Interface Condition ◽  
Large Temperature ◽  
Bonded Interface ◽  
The Impact ◽  
Element Method

Through-silicon via (TSV) technology is expected to overcome the limitations of I/O density and helps in enhancing system performance of conventional flip chip packages. One of the challenges for producing reliable TSV packages is the stacking and joining of thin wafers or dies. In the case of the conventional solder interconnections, many reliability issues arise at the interface between solder and copper bump. As an alternative solution, Cu-Cu direct thermo-compression bonding (CuDB) is a possible option to enable three-dimension (3D) package integration. CuDB has several advantages over the solder based micro bump joining, such as reduction in soldering process steps, enabling higher interconnect density, enhanced thermal conductivity and decreased concerns about intermetallic compounds (IMC) formation. Critical issue of CuDB is bonding interface condition. After the bonding process, Cu-Cu direct bonding interface is obtained. However, several researchers have reported small voids at the bonded interface. These defects can act as an initial crack which may lead to eventual fracture of the interface. The fracture could happen due to the thermal expansion coefficient (CTE) mismatch between the substrate and the chip during the postbonding process, board level reflow or thermal cycling with large temperature changes. In this study, a quantitative assessment of the energy release rate has been made at the CuDB interface during temperature change finite element method (FEM). A parametric study is conducted to analyze the impact of the initial crack location and the material properties of surrounding materials. Finally, design recommendations are provided to minimize the probability of interfacial delamination in CuDB.

scholarly journals Consumption of Select Dietary Emulsifiers Exacerbates the Development of Spontaneous Intestinal Adenoma

2021 ◽  
Vol 22 (5) ◽  
pp. 2602
Author(s):  
Emilie Viennois ◽  
Benoit Chassaing
Keyword(s):  
Intestinal Inflammation ◽  
Tumor Development ◽  
Low Grade ◽  
Gastrointestinal Cancers ◽  
Cancer Initiation ◽  
And Function ◽  
The Impact ◽  
Chronic Intestinal Inflammation ◽  
Low Grade Inflammation ◽  
Intestinal Adenoma

Inflammation is a well-characterized critical driver of gastrointestinal cancers. Previous findings have shown that intestinal low-grade inflammation can be promoted by the consumption of select dietary emulsifiers, ubiquitous component of processed foods which alter the composition and function of the gut microbiota. Using a model of colitis-associated cancer, we previously reported that consumption of the dietary emulsifiers carboxymethylcellulose or polysorbate-80 exacerbated colonic tumor development. Here, we investigate the impact of dietary emulsifiers consumption on cancer initiation and progression in a genetical model of intestinal adenomas. In APCmin mice, we observed that dietary emulsifiers consumption enhanced small-intestine tumor development in a way that appeared to be independent of chronic intestinal inflammation but rather associated with emulsifiers’ impact on the proliferative status of the intestinal epithelium as well as on intestinal microbiota composition in both male and female mice. Overall, our findings further support the hypothesis that emulsifier consumption may be a new modifiable risk factor for colorectal cancer (CRC) and that alterations in host–microbiota interactions can favor gastrointestinal carcinogenesis in individuals with a genetical predisposition to such disorders.

scholarly journals QOL-36. USE OF CANNABINOIDS IN THE PEDIATRIC CENTRAL NERVOUS SYSTEM TUMOR POPULATION

2020 ◽  
Vol 22 (Supplement_3) ◽  
pp. iii438-iii438
Author(s):  
Kathleen Dorris ◽  
Jessica Channell ◽  
Ashley Mettetal ◽  
Molly Hemenway ◽  
Natalie Briones ◽  
...  
Keyword(s):  
Quality Of Life ◽  
Central Nervous System ◽  
Nervous System ◽  
Cell Activity ◽  
Cns Tumors ◽  
Low Grade ◽  
Tumor Type ◽  
Central Nervous System Tumor ◽  
The Impact

Abstract BACKGROUND Cannabinoids, including cannabidiol (CBD) and tetrahydrocannabinol (THC), are a class of compounds found in marijuana. Numerous studies in adults have examined cannabinoid use in management of cancer-related symptoms such as nausea, anorexia, and pain. Less is known about the use in the pediatric oncology population. METHODS A prospective observational study has been ongoing since 2016 at Children’s Hospital Colorado to evaluate cannabinoids’ impact using PedsQL™ modules on quality of life of pediatric patients with central nervous system (CNS) tumors who are 2–18 years old. Laboratory assessments of T-cell activity and pharmacokinetics of CBD, THC and associated metabolites are in process. Diaries with exploratory information on cannabinoid use patterns are being collected. RESULTS Thirty-three patients (14:19; male:female) have been enrolled with a median age of 6.4 years (range, 2.9–17.7 years). The most common tumor type in enrolled patients is embryonal tumors (13/33; 39%). Nine (27%) patients have low-grade glial/glioneuronal tumors, and eight (24%) had high-grade/diffuse midline gliomas. The remaining patients had ependymoma or craniopharyngioma. The median time on cannabinoids is 9 months. Most (n=20) patients have used oral products with CBD and THC. One patient continues on cannabinoid therapy in follow up. Preliminary immune function analyses identified impaired neutrophil superoxide anion production and chemotaxis in patients taking cannabinoids at early time points on therapy. CONCLUSIONS Families of children with various CNS tumors are pursuing cannabinoid therapy for both antitumor and supportive care purposes. Analysis of the impact of cannabinoids on patients’ quality of life is ongoing.

scholarly journals A Retrospective Experience of Helicobacter pylori Histology in a Large Sample of Subjects in Northern Italy

Life ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 650
Author(s):  
Davide Giuseppe Ribaldone ◽  
Carlo Zurlo ◽  
Sharmila Fagoonee ◽  
Chiara Rosso ◽  
Angelo Armandi ◽  
...  
Keyword(s):  
Helicobacter Pylori ◽  
Large Population ◽  
Population Data ◽  
Signet Ring Cell ◽  
Current Data ◽  
Low Grade ◽  
Gastric Cardia Adenocarcinoma ◽  
Significant Difference ◽  
H Pylori ◽  
The Impact

Updated data about the prevalence of Helicobacter pylori (H. pylori) and its correlation with histological results are scarce. The aim of our study was to provide current data on the impact of H. pylori in a third-level endoscopy service. We performed a large, retrospective study analyzing the results of all histological samples of gastroscopy from the year 2019. In total, 1512 subjects were included. The prevalence of H. pylori was 16.8%. A significant difference between the prevalence in subjects born in Italy and those from eastern Europe, south America, or Africa was found (p < 0.0001, p = 0.006, and p = 0.0006, respectively). An association was found between H. pylori and active superficial gastritis (p < 0.0001). Current H. pylori and/or a previous finding of H. pylori was related to antral atrophy (p < 0.0001). Fifteen patients had low-grade dysplasia. There were no statistically significant associations with current or past H. pylori infection. One patient presented gastric cardia adenocarcinoma with regular gastric mucosa. One patient, H. pylori positive, was diagnosed with gastric signet ring cell adenocarcinoma in a setting of diffuse atrophy, without metaplasia.. Our study provides updated, solid (biopsy diagnosis and large population) data on the prevalence of H. pylori infection in a representative region of southern Europe.

scholarly journals TissueCypher Barrett’s esophagus assay impacts clinical decisions in the management of patients with Barrett’s esophagus

2021 ◽  
Vol 09 (03) ◽  
pp. E348-E355
Author(s):  
David L. Diehl ◽  
Harshit S. Khara ◽  
Nasir Akhtar ◽  
Rebecca J. Critchley-Thorne
Keyword(s):  
High Risk ◽  
Barrett’S Esophagus ◽  
Barrett's Esophagus ◽  
Clinical Decision Making ◽  
Eradication Therapy ◽  
Low Risk ◽  
Management Approach ◽  
Low Grade ◽  
Management Decisions ◽  
The Impact

Abstract Background and study aims The TissueCypher Barrett’s Esophagus Assay is a novel tissue biomarker test, and has been validated to predict progression to high-grade dysplasia (HGD) and esophageal adenocarcinoma (EAC) in patients with Barrett’s esophagus (BE). The aim of this study was to evaluate the impact of TissueCypher on clinical decision-making in the management of BE. Patients and methods TissueCypher was ordered for 60 patients with non-dysplastic (ND, n = 18) BE, indefinite for dysplasia (IND, n = 25), and low-grade dysplasia (LGD, n = 17). TissueCypher reports a risk class (low, intermediate or high) for progression to HGD or EAC within 5 years. The impact of the test results on BE management decisions was assessed. Results Fifty-two of 60 patients were male, mean age 65.2 ± 11.8, and 43 of 60 had long segment BE. TissueCypher results impacted 55.0 % of management decisions. In 21.7 % of patients, the test upstaged the management approach, resulting in endoscopic eradication therapy (EET) or shorter surveillance interval. The test downstaged the management approach in 33.4 % of patients, leading to surveillance rather than EET. In the subset of patients whose management plan was changed, upstaging was associated with a high-risk TissueCypher result, and downstaging was associated with a low-risk result (P < 0.0001). Conclusions TissueCypher was used as an adjunct to support a surveillance-only approach in 33.4 % of patients. Upstaging occurred in 21.7 % of patients, leading to therapeutic intervention or increased surveillance. These results indicate that the TissueCypher test may enable physicians to target EET for TissueCypher high-risk BE patients, while reducing unnecessary procedures in TissueCypher low-risk patients.

scholarly journals THU0389 OBESITY IS A STRONG PREDICTOR OF WORSE CLINICAL OUTCOMES AND TREATMENT RESPONSES TO BIOLOGICS IN PATIENTS WITH ANKYLOSING SPONDYLITIS

2020 ◽  
Vol 79 (Suppl 1) ◽  
pp. 429.2-429
Author(s):  
L. Hu ◽  
X. Ji ◽  
F. Huang
Keyword(s):  
Ankylosing Spondylitis ◽  
Disease Activity ◽  
Clinical Outcomes ◽  
Normal Weight ◽  
Low Grade ◽  
Hla B27 ◽  
Treatment Responses ◽  
The Impact ◽  
Overweight Or Obesity

Background:Obesity population are rising rapidly and have become a major health issue. Studies have shown that obesity is a low-grade inflammatory status characterized by increase in proinflammatory cytokines.Objectives:To examine the impact of overweight or obesity on disease activity and treatment responses to biologics in patients with ankylosing spondylitis (AS) in a real-world setting.Methods:Body mass index (BMI) is available in 1013 patients from the Chinese Ankylosing Spondylitis Imaging Cohort (CASPIC). Differences in clinical outcomes (such as BASDAI, ASDAS, BASFI, and ASAS HI) and treatment responses to biologics (ΔBASDAI and ΔASDAS) over 3, 6, 9, and 12 months are assessed between BMI categories (normal weight BMI <24 kg/m2; overweight BMI=24-28 kg/m2; obesity BMI ≥28 kg/m2) using Kruskal-Wallis test. The association between BMI and clinical characteristics and treatment responses to biologics was determined, and multivariate median regression analyses were conducted to adjust for confounders (such as age, gender, smoke, and HLA-B27).Results:Among 1013 patients with AS, overweight accounts for 33%, while obesity for 12.4%. There were significant differences between patients who were obese or overweight and those with a normal weight regarding clinical outcomes (BASDAI: 2.90/2.56 vs 2.21; ASDAS-CRP: 2.20/1.99 vs 1.81; BASFI: 2.13/1.69 vs 1.38; ASAS HI: 6.87/5.29 vs 5.12 and BASMI: 2.35/1.76 vs 1.62; all P<0.05). After adjusting for age, gender, smoke, and HLA-B27, obesity remained associated with higher disease activity (BASDAI: β=0.55, P=0.005; ASDAS-CRP: β=0.40, P<0.001), poorer functional capacity (BASFI: β=0.58, P=0.001), worse health index (ASAS HI: β=1.92, P<0.001) and metrology index (BASMI: β=0.71, P=0.013). For TNFi users, BMI was found to be negatively correlated with changes in disease activity (ΔBASDAI and ΔASDAS) in the multivariate regression model (all P<0.05), and overweight and obese patients showed an unsatisfactory reduction in disease activity during 3-month, 6-month, 9-month, and 12-month follow-up period, compared to normal weight patients (all P<0.05).Conclusion:Overweight or obesity impacts greatly on clinical outcomes and treatment responses to biologics in patients with ankylosing spondylitis, which argues strongly for obesity management to become central to prevention and treatment strategies in patients with AS.References:[1]Maachi M, Pieroni L, Bruckert E, et al. Systemic low-grade inflammation is related to both circulating and adipose tissue TNFalpha, leptin and IL-6 levels in obese women. Int J Obes Relat Metab Disord 2004;28:993–7.Figure 1.Changes of disease activity for TNFi users during 3-, 6-, 9- and 12-month follow-up according to BMI categories. a: vs. normal weight, P<0.05 in 3 months; b: vs. normal weight, P<0.05 in 6 months; c: vs. normal weight, P<0.05 in 9 months; d: vs. normal weight, P<0.05 in 12 months.Acknowledgments:We appreciate the contribution of the present or former members of the CASPIC study group.Disclosure of Interests:None declared

scholarly journals The DEAD/DEAH Box Helicase, DDX11, Is Essential for the Survival of Advanced Clear Cell Renal Cell Carcinoma and Is a Determinant of PARP Inhibitor Sensitivity

Cancers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 2574
Author(s):  
Jee Soo Park ◽  
Myung Eun Lee ◽  
Won Sik Jang ◽  
Koon Ho Rha ◽  
Seung Hwan Lee ◽  
...  
Keyword(s):  
Renal Cell Carcinoma ◽  
Cell Carcinoma ◽  
Renal Cell ◽  
Quantitative Polymerase Chain Reaction ◽  
Parp Inhibitor ◽  
Renal Tumors ◽  
Low Grade ◽  
Normal Kidney ◽  
The Dead ◽  
The Impact

Genes associated with the DEAD-box helicase DDX11 are significant biomarkers of aggressive renal cell carcinoma (RCC), but their molecular function is poorly understood. We analyzed the molecular pathways through which DDX11 is involved in RCC cell survival and poly (ADP-ribose) polymerase (PARP) inhibitor sensitivity. Immunohistochemistry and immunoblotting determined DDX11 expression in normal kidney tissues, benign renal tumors, and RCC tissues and cell lines. Quantitative polymerase chain reaction validated the downregulation of DDX11 in response to transfection with DDX11-specific small interfering RNA. Proliferation analysis and apoptosis assays were performed to determine the impact of DDX11 knockdown on RCC cells, and the relevant effects of sunitinib, olaparib, and sunitinib plus olaparib were evaluated. DDX11 was upregulated in high-grade, advanced RCC compared to low-grade, localized RCC, and DDX11 was not expressed in normal kidney tissues or benign renal tumors. DDX11 knockdown resulted in the inhibition of RCC cell proliferation, segregation defects, and rapid apoptosis. DDX11-deficient RCC cells exhibited significantly increased sensitivity to olaparib compared to sunitinib alone or sunitinib plus olaparib combination treatments. Moreover, DDX11 could determine PARP inhibitor sensitivity in RCC. DDX11 could serve as a novel therapeutic biomarker for RCC patients who are refractory to conventional targeted therapies and immunotherapies.

scholarly journals Impact of Pathological Stratification on the Clinical Outcomes of Advanced Well-Differentiated/Dedifferentiated Liposarcoma Treated with Trabectedin

Cancers ◽  
2021 ◽  
Vol 13 (6) ◽  
pp. 1453
Author(s):  
Chiara Fabbroni ◽  
Giovanni Fucà ◽  
Francesca Ligorio ◽  
Elena Fumagalli ◽  
Marta Barisella ◽  
...  
Keyword(s):  
Clinical Outcomes ◽  
Proportional Hazards ◽  
Case Series ◽  
Progression Free Survival ◽  
Cox Proportional Hazards ◽  
Low Grade ◽  
High Grade ◽  
Retrospective Case ◽  
Well Differentiated ◽  
The Impact

Background. We previously showed that grading can prognosticate the outcome of retroperitoneal liposarcoma (LPS). In the present study, we aimed to explore the impact of pathological stratification using grading on the clinical outcomes of patients with advanced well-differentiated LPS (WDLPS) and dedifferentiated LPS (DDLPS) treated with trabectedin. Patients: We included patients with advanced WDLPS and DDLPS treated with trabectedin at the Fondazione IRCCS Istituto Nazionale dei Tumori between April 2003 and November 2019. Tumors were categorized in WDLPS, low-grade DDLPS, and high-grade DDLPS according to the 2020 WHO classification. Patients were divided in two cohorts: Low-grade (WDLPS/low-grade DDLPS) and high-grade (high-grade DDLPS). Results: A total of 49 patients were included: 17 (35%) in the low-grade cohort and 32 (65%) in the high-grade cohort. Response rate was 47% in the low-grade cohort versus 9.4% in the high-grade cohort (logistic regression p = 0.006). Median progression-free survival (PFS) was 13.7 months in the low-grade cohort and 3.2 months in the high-grade cohort. Grading was confirmed as an independent predictor of PFS in the Cox proportional-hazards regression multivariable model (adjusted hazard ratio low-grade vs. high-grade: 0.45, 95% confidence interval: 0.22–0.94; adjusted p = 0.035). Conclusions: In this retrospective case series, sensitivity to trabectedin was higher in WDLPS/low-grade DDLPS than in high-grade DDLPS. If confirmed in larger series, grading could represent an effective tool to personalize the treatment with trabectedin in patients with advanced LPS.

Sign in / Sign up

Export Citation Format

Share Document