scholarly journals Operating Range for a Combined, Building-Scale Liquid Air Energy Storage and Expansion System: Energy and Exergy Analysis

Entropy ◽  
2018 ◽  
Vol 20 (10) ◽  
pp. 770 ◽  
Author(s):  
Todd Howe ◽  
Anthony Pollman ◽  
Anthony Gannon

This paper presents the results of an ideal theoretical energy and exergy analysis for a combined, building scale Liquid Air Energy Storage (LAES) and expansion turbine system. This work identifies the upper bounds of energy and exergy efficiency for the combined LAES-expansion system which has not been investigated. The system uses the simple Linde-Hampson and pre-cooled Linde-Hampson cycles for the liquefaction subsystem and direct expansion method, with and without heating above ambient temperature, for the energy production subsystem. In addition, the paper highlights the effectiveness of precooling air for liquefaction and heating air beyond ambient temperature for energy production. Finally, analysis of the system components is presented with an aim toward identifying components that have the greatest impact on energy and exergy efficiencies in an ideal environment. This work highlights the engineering trade-space and serves as a prescription for determining the merit or measures of effectiveness for an engineered LAES system in terms of energy and exergy. The analytical approach presented in this paper may be applied to other LAES configurations in order to identify optimal operating points in terms of energy and exergy efficiencies.

Energies ◽  
2020 ◽  
Vol 13 (18) ◽  
pp. 4842 ◽  
Author(s):  
Ryszard Zwierzchowski ◽  
Marcin Wołowicz

The paper contains a simplified energy and exergy analysis of pumps and pipelines system integrated with Thermal Energy Storage (TES). The analysis was performed for a combined heat and power plant (CHP) supplying heat to the District Heating System (DHS). The energy and exergy efficiency for the Block Part of the Siekierki CHP Plant in Warsaw was estimated. CHP Plant Siekierki is the largest CHP plant in Poland and the second largest in Europe. The energy and exergy analysis was executed for the three different values of ambient temperature. It is according to operation of the plant in different seasons: winter season (the lowest ambient temperature Tex = −20 °C, i.e., design point conditions), the intermediate season (average ambient temperature Tex = 1 °C), and summer (average ambient temperature Tex = 15 °C). The presented results of the analysis make it possible to identify the places of the greatest exergy destruction in the pumps and pipelines system with TES, and thus give the opportunity to take necessary improvement actions. Detailed results of the energy-exergy analysis show that both the energy consumption and the rate of exergy destruction in relation to the operation of the pumps and pipelines system of the CHP plant with TES for the tank charging and discharging processes are low.


2020 ◽  
Vol 143 (5) ◽  
Author(s):  
Youssef Mazloum ◽  
Haytham Sayah ◽  
Maroun Nemer

Abstract The balance between supply and demand for electricity is mainly disrupted by the growing contribution of renewable energy sources to the electrical grid since these sources are intermittent by nature. Therefore, the energy storage systems, mainly those of considerable size, become essential to restore the electricity balance. The compressed air energy storage (CAES) system is one of the mature technologies used to store electricity on a large scale. Therefore, this article discusses the energy and exergy analysis of different configurations of a constant-pressure CAES system to improve its overall efficiency and energy density. The exergy efficiency of our basic adiabatic configuration using water as thermal storage medium is 56.4% and the energy density is 12.17 kWh/m3. The results show that the CAES system using a packed bed of quartzite rock as thermal storage medium has the best efficiency (67.2%) and energy density (17 kWh/m3) among adiabatic systems. The diabatic CAES systems could have a net efficiency up to 70.1% and an energy density up to 31.95 kWh/m3 by using combustion chambers. Finally, the waste heat recovery from other installations such as a gas turbine power plant has the potential to improve the energy density to 20.53 kWh/m3 without using fossil fuel sources.


2018 ◽  
Vol 2018 ◽  
pp. 1-14 ◽  
Author(s):  
Vikram C. Patil ◽  
Paul I. Ro

Optimal utilization of renewable energy resources needs energy storage capability in integration with the electric grid. Ocean compressed air energy storage (OCAES) can provide promising large-scale energy storage. In OCAES, energy is stored in the form of compressed air under the ocean. Underwater energy storage results in a constant-pressure storage system which has potential to show high efficiency compared to constant-volume energy storage. Various OCAES concepts, namely, diabatic, adiabatic, and isothermal OCAES, are possible based on the handling of heat in the system. These OCAES concepts are assessed using energy and exergy analysis in this paper. Roundtrip efficiency of liquid piston based OCAES is also investigated using an experimental liquid piston compressor. Further, the potential of improved efficiency of liquid piston based OCAES with use of various heat transfer enhancement techniques is investigated. Results show that adiabatic OCAES shows improved efficiency over diabatic OCAES by storing thermal exergy in thermal energy storage and isothermal OCAES shows significantly higher efficiency over adiabatic and diabatic OCAES. Liquid piston based OCAES is estimated to show roundtrip efficiency of about 45% and use of heat transfer enhancement in liquid piston has potential to improve roundtrip efficiency of liquid piston based OCAES up to 62%.


Energies ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 945
Author(s):  
Lukasz Szablowski ◽  
Piotr Krawczyk ◽  
Marcin Wolowicz

Efficiently storing energy on a large scale poses a major challenge and one that is growing in importance with the increasing share of renewables in the energy mix. The only options at present are either pumped hydro or compressed air storage. One novel alternative is to store energy using liquid air, but this technology is not yet fully mature and requires substantial research and development, including in-depth energy and exergy analysis. This paper presents an exergy analysis of the Adiabatic Liquid Air Energy Storage (A-LAES) system based on the Linde–Hampson cycle. The exergy analysis was carried out for four cases with different parameters, in particular the discharge pressure of the air at the inlet of the turbine (20, 40, 100, 150 bar). The results of the analysis show that the greatest exergy destruction can be observed in the air evaporator and in the Joule–Thompson valve. In the case of air evaporator, the destruction of exergy is greatest for the lowest discharge pressure, i.e., 20 bar, and reaches over 118 MWh/cycle. It decreases with increasing discharge pressure, down to approximately 24 MWh/cycle for 150 bar, which is caused by a decrease in the heat of vaporization of air. In the case of Joule–Thompson valve, the changes are reversed. The highest destruction of exergy is observed for the highest considered discharge pressure (150 bar) and amounts to over 183 MWh/cycle. It decreases as pressure is lowered to 57.5 MWh/cycle for 20 bar. The other components of the system do not show exergy destruction greater than approximately 50 MWh/cycle for all considered pressures. Specific liquefaction work of the system ranged from 0.189 kWh/kgLA to 0.295 kWh/kgLA and the efficiency from 44.61% to 55.18%.


2016 ◽  
Author(s):  
Ασπασία Χατζηπασχάλη

Τις τελευταίες δεκαετίες, υπάρχει έντονο ενδιαφέρον στις εναλλακτικές μορφές ενέργειας, ως αποτέλεσμα των αυξημένων ενεργειακών απαιτήσεων σε συνδυασμό και με το πρόβλημα της κλιματικής αλλαγής. Επιπρόσθετα, η συνεχής αύξηση του πληθυσμού και η εκβιομηχάνιση των κοινωνιών οδηγούν συχνά στην υποβάθμιση των οικοσυστημάτων, στα οποία στηρίζεται η ανθρώπινη ζωή. Για το λόγο αυτό, στη σύγχρονη βιομηχανική κοινωνία είναι αδήριτη η ανάγκη για την κατάλληλη επεξεργασία των διαφόρων αποβλήτων που προέρχονται από τις βιομηχανίες πριν την απόρριψή τους, προκειμένου να προληφθεί η ρύπανση του εδάφους και των υδάτινων συστημάτων (λιμνών, ποταμών, θάλασσας, υπόγειων υδροφόρων). Το τυρόγαλο που προέρχεται από τις βιομηχανίες γάλακτος κατά την διαδικασία παραγωγής τυριού είναι ένας από τους σημαντικότερους βιομηχανικούς ρυπαντές που από τη φύση του περιέχει υψηλό οργανικό φορτίο (COD). Συγχρόνως όμως, το τυρόγαλο αποτελεί την πρώτη ύλη για παραγωγή βιοαερίου. Η παραγωγή βιοαερίου και άλλων εμπορεύσιμων προϊόντων με ταυτόχρονη μείωση του COD μέσω κατάλληλων μεθόδων, αποδεικνύουν ότι το τυρόγαλο είναι μια σημαντική πηγή ενέργειας και όχι ένας απλός ρυπαντής. Η παρουσία βιοαποικοδομήσιμων συστατικών στο τυρόγαλο σε συνδυασμό και με τα πλεονεκτήματα της διεργασίας της Αναερόβιας Χώνευσης συγκριτικά με άλλες μεθόδους, καθιστούν την μέθοδο αυτή ως ιδιαίτερα κατάλληλη για την επεξεργασία των αποβλήτων αυτών.Στην παρούσα διατριβή μελετάται η τεχνολογία της αναερόβιας χώνευσης για την επεξεργασία των αποβλήτων τυρόγαλου σε συνδυασμό με την χρήση μικροστροβίλων για την παραγωγή ενέργειας. Η επιλογή της χρήσης μικροστροβίλων έναντι άλλων συστημάτων οφείλεται στα πλεονεκτήματα τους που τους καθιστούν ικανούς να χρησιμοποιηθούν σε εφαρμογές κατανεμημένης παραγωγής ηλεκτρικής ενέργειας, «smart grids», υβριδικά συστήματα και συστήματα συμπαραγωγής. Αρχικά παρουσιάζεται μία ανασκόπηση των πιο αντιπροσωπευτικών εφαρμογών αναερόβιας χώνευσης για επεξεργασία αποβλήτων τυρόγαλου τόσο σε πιλοτική όσο και σε εργαστηριακή κλίμακα. Επιπρόσθετα, γίνεται μία προσπάθεια αναγωγής των αποτελεσμάτων των διαφόρων ερευνών σε μια κοινή συγκριτική βάση, προκειμένου να αποτυπωθεί η κατάσταση της τεχνολογίας σε αντίστοιχα γραφήματα. Στη συνέχεια, αναπτύσσεται ένα μοντέλο προσομοίωσης του συστήματος αναερόβιας χώνευσης σε συνδυασμό με έναν μικροστρόβιλο και εξετάζονται δύο διαφορετικά σενάρια. Στο πρώτο σενάριο μελετάται η ενσωμάτωση ενός εμπορικά διαθέσιμου μικροστροβίλου στο σύστημα αναερόβιας χώνευσης για παραγωγή ηλεκτρικής ενέργειας, με καύση μόνο ενός μέρους του παραγόμενου βιοαερίου στον μικροστρόβιλο, ενώ το υπόλοιπο καίγεται στον καυστήρα για παραγωγή ατμού. Στην περίπτωση αυτή, η επιλογή του καταλληλότερου μικροστροβίλου έγινε με σκοπό να επιτευχθεί η μέγιστη παραγωγή ηλεκτρικής ενέργειας με ταυτόχρονη κάλυψη των θερμικών απαιτήσεων (παραγωγή ατμού) της μονάδας. Στο δεύτερο σενάριο μελετάται η περίπτωση μέγιστης παραγωγής ηλεκτρικής ενέργειας μέσω μικροστροβίλου, χωρίς κανένα περιορισμό όσον αφορά την παραγωγή σε ατμό. Τα δεδομένα για την μοντελοποίηση του συστήματος αναερόβια χώνευσης προέρχονται από ένα εργοστάσιο παραγωγής τυριών που λειτουργεί στην Ελλάδα, ενώ τα δεδομένα για τους μικροστροβίλους έχουν ληφθεί από τους αντίστοιχους κατασκευαστές τους. Ως εκ τούτου, προέκυψαν δύο διαφορετικά συστήματα τα οποία αναλύονται και εκτιμώνται σε σχέση με τα διαθέσιμα στοιχεία στη βιβλιογραφία. Στη συνέχεια διεξάγεται εξεργειακή ανάλυση των συστημάτων αυτών. Τα αποτελέσματα έδειξαν ότι τα συστήματα αυτά μπορεί να επιτύχουν υψηλούς βαθμούς απόδοσης, παρά την εμφάνιση υψηλών τιμών καταστροφών εξέργειας και αναστρεψιμοτήτων, κυρίως στον καυστήρα για το πρώτο σενάριο και στον θάλαμο καύσης του μικροστροβίλου για το δεύτερο σενάριο. Στη συνέχεια, πραγματοποιήθηκε οικονομική ανάλυση μέσω της μεθόδους Καθαρής Παρούσας Αξίας (ΚΠΑ). Τα αποτελέσματα δείχνουν πως πρόκειται για κερδοφόρες επενδύσεις, με υψηλά κέρδη από τον πρώτο χρόνο λειτουργίας. Επιπλέον, διεξήχθη παραμετρική ανάλυση ως μέθοδος βελτιστοποίησης. Στην περίπτωση αυτή, εξετάσθηκε η επίδραση ορισμένων σημαντικών παραμέτρων λειτουργίας όπως ο ισεντροπικός βαθμός απόδοσης του στροβίλου και του συμπιεστή και η επίδραση διαφόρων θερμοκρασιών κυρίως στη συνολική εξεργειακή απόδοση των συστημάτων και στη τιμή της ΚΠΑ. Τα αποτελέσματα έδειξαν ότι τα συστήματα αυτά μπορούν να επιτύχουν υψηλές αποδόσεις και τιμές ΚΠΑ με κατάλληλη επιλογή των παραμέτρων σχεδίασης.


Sign in / Sign up

Export Citation Format

Share Document