scholarly journals Effects of Different Content of Phosphorus Slag Composite Concrete: Heat Evolution, Sulphate-Corrosion Resistance and Volume Deformation

Crystals ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 1293
Author(s):  
Kuisheng Liu ◽  
Yong Cui
Keyword(s):  
Temperature Rise ◽  
Control Sample ◽  
Drying Shrinkage ◽  
Strength Loss ◽  
Adiabatic Temperature ◽  
Adiabatic Temperature Rise ◽  
Binder Ratio ◽  
L 22 ◽  
Water Binder Ratio

Phosphorus slag (PS) and limestone (LS) composite (PLC) were prepared with a mass ratio of 1:1. The effects of the content of PLC and the water/binder ratio on the mechanical properties, durability and dry shrinkage of concrete were studied via compressive strength, electric flux, sulfate dry/wet cycle method, saturated drainage method, isothermal calorimeter, adiabatic temperature rise instrument and shrinkage deformation instrument. The results show that PLC can greatly reduce the adiabatic temperature rise of concrete. The adiabatic temperature rise is 55 °C with 33 wt.% PLC, 10 °C lower than that of the control sample. The addition in the content of PLC does not affect the long-term strength of concrete. When the water/binder ratio decreases by 0.1–0.15, the long-term strength of concrete with PLC increases by about 10%, compared with the control group. At the age of 360 days, the chloride permeability of L-11 (i.e., the content of PLC was 20%, the water/binder ratio was 0.418) and L-22 (i.e., the content of PLC was 33%, the water/binder ratio was 0.39) decrease to the “very low” grade. The strength loss rate of L-11 and L-22 after 150 sulfate dry/wet cycles is about 18.5% and 19%, respectively, which is 60% of the strength loss rate of the control sample. The drying shrinkage of L-11 and L-22 reduces by 4.7% and 9.5%, respectively, indicating that PLC can also reduce the drying shrinkage.

Influence of the Fly-Ash Content of Concrete at Low Water-Binder Ratio on Hydration Degree of Binders and Cement

2011 ◽  
Vol 250-253 ◽  
pp. 445-449
Author(s):  
Li Wei Xu ◽  
Jian Lan Zheng
Keyword(s):  
Fly Ash ◽  
Temperature Rise ◽  
High Performance Concrete ◽  
Ash Content ◽  
Adiabatic Temperature ◽  
Mineral Admixture ◽  
Hydration Degree ◽  
Adiabatic Temperature Rise ◽  
Binder Ratio ◽  
Water Binder Ratio

The hydration degree of binders and cement is investigated by measuring the adiabatic- temperature rise of concrete at low water-binder ratio with different fly-ash content. The results denote that, with a constant water-binder ratio, both of the hydration degree of binders and that of cement decrease with the increasing fly-ash content in the early stage. In a later stage, however, the hydration degree of cement increases with the increasing fly-ash content and the hydration degree of binders peaks when the fly-ash content is 35%. Fly ash is one of the mineral admixture of which high-performance concrete is made up. It brings down the rise of concrete temperature significantly and helps solve the problems of shrinkage and crack of concrete structure. Because the hydration mechanism in common concrete is different from that in concrete with low water-binder ratio, and the hydration environment is different between concrete and cement pastes, to determine the adiabatic-temperature rise of concrete directly conforms to the actual situation. The adiabatic-temperature rise, adiabatic-temperature-rise rate, hydration degree of both binders and cement are investigated by measuring adiabatic-temperature rise of concrete with different fly-ash content.

Modeling the Heat of Hydration of Concrete Incorporating Fly Ash

2016 ◽  
Vol 705 ◽  
pp. 332-337 ◽  
Author(s):  
Zheng Gang Lu ◽  
Xiu Xin Wang
Keyword(s):  
Fly Ash ◽  
Temperature Rise ◽  
Heat Of Hydration ◽  
Hyperbolic Type ◽  
Adiabatic Temperature ◽  
Adiabatic Temperature Rise ◽  
Equivalent Age ◽  
Binder Ratio ◽  
Water Binder Ratio ◽  
Release Coefficient

The hydration evolution of concrete with different water-binder ratios and fly ash replacement percentages are studied by experimental investigation. Based on equivalent age concept, the effect of water-binder ratio as well as fly ash dosage on the ultimate temperature rise and heat release coefficient are analyzed with the hyperbolic-type calculating model of adiabatic temperature rise adopted. It is indicated that the adiabatic temperature rise will be reduced with the increase of water-binder ratio and the incorporation of fly ash. The hydration evolution process will be accelerated with the decrease of water-binder ratio, but slowed down when the amount of fly ash is enhanced.

Experimental Study on Influential Factors of Adiabatic Temperature Rise for Mass Concrete

2011 ◽  
Vol 306-307 ◽  
pp. 917-922
Author(s):  
Dong Dong Wang ◽  
Wei Li Tian ◽  
Cheng Qi Wang
Keyword(s):  
Temperature Rise ◽  
Heat Liberation ◽  
Influential Factors ◽  
Adiabatic Temperature ◽  
Mineral Admixtures ◽  
Mass Concrete ◽  
Adiabatic Temperature Rise ◽  
Exothermic Process ◽  
Binder Ratio ◽  
Main Factor

Experiments on adiabatic temperature rise are systematically carried out in this paper, the characteristics of adiabatic temperature rise of concrete with different mineral admixtures are compared. The influence of binder amount, water-binder ratio, placing temperature and superplasticizer is also studied. The results reflect that binder is the main factor affecting adiabatic temperature rise, mineral admixtures such as fly ash can significantly reduce the rate and amount of heat development, large quantity substitution of slag in concrete can relieve the concentrative heat liberation, the retarded superplasticizer can prolong the exothermic process effectively and high placing temperature has adverse effect on temperature control of mass concrete.

Effect of Slag Characteristics on Adiabatic Temperature Rise of Blended Concrete

2022 ◽  
Author(s):  
Hai Zhu ◽  
Dhanushika Gunatilake Mapa ◽  
Catherine Lucero ◽  
Kyle A. Riding ◽  
A. Zayed
Keyword(s):  
Temperature Rise ◽  
Adiabatic Temperature ◽  
Adiabatic Temperature Rise

Kinetic Model of Adiabatic Temperature Rise of Mass Concrete

2021 ◽  
Vol 13 (5) ◽  
pp. 771-780
Author(s):  
Shou-Kai Chen ◽  
Bo-Wen Xu
Keyword(s):  
Temperature Field ◽  
Temperature Rise ◽  
Initial Conditions ◽  
Dynamic Change ◽  
Adiabatic Temperature ◽  
Model Parameters ◽  
Hydration Reaction ◽  
Mass Concrete ◽  
Adiabatic Temperature Rise ◽  
Proposed Model

The adiabatic temperature rise model of mass concrete is very important for temperature field simulation, same to crack resistance capacity and temperature control of concrete structures. In this research, a thermal kinetics analysis was performed to study the exothermic hydration reaction process of concrete, and an adiabatic temperature rise model was proposed. The proposed model considers influencing factors, including initial temperature, temperature history, activation energy, and the completion degree of adiabatic temperature rise and is theoretically mature and definitive in physical meaning. It was performed on different initial temperatures for adiabatic temperature rise test; the data were employed in a regression analysis of the model parameters and initial conditions. The same function was applied to describe the dynamic change of the adiabatic temperature rise rates for different initial temperatures and different temperature changing processes and subsequently employed in a finite element analysis of the concrete temperature field. The test results indicated that the proposed model adequately fits the data of the adiabatic temperature rise test, which included different initial temperatures, and accurately predicts the changing pattern of adiabatic temperature rise of concrete at different initial temperatures. Compared with the results using the traditional age-based adiabatic temperature rise model, the results of a calculation example revealed that the simulated calculation results using the proposed model can accurately reflect the temperature change pattern of concrete in heat dissipation conditions.

scholarly journals Convenient Evaluation Method of Adiabatic Temperature Rise using Mortar Sample

2010 ◽  
Vol 48 (12) ◽  
pp. 15-22
Author(s):  
E. Maruya ◽  
H. Misumi ◽  
T. Takahashi ◽  
E. Sakai
Keyword(s):  
Temperature Rise ◽  
Evaluation Method ◽  
Adiabatic Temperature ◽  
Mortar Sample ◽  
Adiabatic Temperature Rise

scholarly journals Experimental Study on Durability Improvement of Fly Ash Concrete with Durability Improving Admixture

2014 ◽  
Vol 2014 ◽  
pp. 1-11 ◽  
Author(s):  
Hong-zhu Quan ◽  
Hideo Kasami
Keyword(s):  
Fly Ash ◽  
Experimental Studies ◽  
Drying Shrinkage ◽  
Replacement Ratio ◽  
Fly Ash Concrete ◽  
Air Content ◽  
Carbonation Resistance ◽  
Binder Ratio ◽  
Water Binder Ratio

In order to improve the durability of fly ash concrete, a series of experimental studies are carried out, where durability improving admixture is used to reduce drying shrinkage and improve freezing-thawing resistance. The effects of durability improving admixture, air content, water-binder ratio, and fly ash replacement ratio on the performance of fly ash concrete are discussed in this paper. The results show that by using durability improving admixture in nonair-entraining fly ash concrete, the compressive strength of fly ash concrete can be improved by 10%–20%, and the drying shrinkage is reduced by 60%. Carbonation resistance of concrete is roughly proportional to water-cement ratio regardless of water-binder ratio and fly ash replacement ratio. For the specimens cured in air for 2 weeks, the freezing-thawing resistance is improved. In addition, by making use of durability improving admixture, it is easier to control the air content and make fly ash concrete into nonair-entraining one. The quality of fly ash concrete is thereby optimized.

Sign in / Sign up

Export Citation Format

Share Document