scholarly journals Thermal Deformation Behavior of Ti-6Mo-5V-3Al-2Fe Alloy

Crystals ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 1245
Author(s):  
Lin Han ◽  
Haoyu Zhang ◽  
Jun Cheng ◽  
Ge Zhou ◽  
Chuan Wang ◽  
...  
Keyword(s):  
Dynamic Recrystallization ◽  
Strain Rate ◽  
Hot Deformation ◽  
Deformation Temperature ◽  
Rate Sensitivity ◽  
Hot Working ◽  
Sensitivity Index ◽  
Strain Rate Sensitivity Index ◽  
Deformation Activation Energy ◽  
New Type

The Gleeble-3800 thermal simulation machine was used to perform hot compression experiments on a new type of β alloy, Ti-6Mo-5V-3Al-2Fe (wt.%), at temperatures of 700–900 °C, strain rates of 5 × 10−1 to 5 × 10−4 s−1, and total strain of 0.7. Transmission and EBSD techniques were used to observe the microstructure. The results show that the deformation activation energy of the alloy was 356.719 KJ/mol, and dynamic recrystallization occurred during the hot deformation. The higher the deformation temperature was, the more obvious the dislocations that occurred and the more sufficient the dynamic recrystallization that occurred, but the effect of strain rate was the opposite. When the deformation temperature was higher than the phase transition point, the recrystallized grains clearly grew up. The calculated strain rate sensitivity index of the alloy was 0.14–0.29. The constitutive equation of hot deformation of Ti-6Mo-5V-3Al-2Fe alloy was established by using the Arrhenius hyperbolic sine equation. The dynamic DMM hot working diagram with the strain of 0.7 was constructed. The relatively good hot working area of the alloy was determined to be the deformation temperature of 700–720 °C and 0.0041–0.0005 s−1.

scholarly journals High-Temperature Deformation Behavior and Microstructural Characterization of Ti-35421 Titanium Alloy

Materials ◽  
2020 ◽  
Vol 13 (16) ◽  
pp. 3623 ◽  
Author(s):  
Danying Zhou ◽  
Hua Gao ◽  
Yanhua Guo ◽  
Ying Wang ◽  
Yuecheng Dong ◽  
...  
Keyword(s):  
Titanium Alloy ◽  
Dynamic Recrystallization ◽  
Strain Rate ◽  
Hot Deformation ◽  
Deformation Behavior ◽  
Deformation Temperature ◽  
Phase Region ◽  
Temperature Deformation ◽  
Β Phase ◽  
Α Phase

A self-designed Ti-35421 (Ti-3Al-5Mo-4Cr-2Zr-1Fe wt%) titanium alloy is a new type of low-cost high strength titanium alloy. In order to understand the hot deformation behavior of Ti-35421 alloy, isothermal compression tests were carried out under a deformation temperature range of 750–930 °C with a strain rate range of 0.01–10 s−1 in this study. Electron backscatter diffraction (EBSD) was used to characterize the microstructure prior to and post hot deformation. The results show that the stress–strain curves have obvious yielding behavior at a high strain rate (>0.1 s−1). As the deformation temperature increases and the strain rate decreases, the α phase content gradually decreases in the α + β phase region. Meanwhile, spheroidization and precipitation of α phase are prone to occur in the α + β phase region. From the EBSD analysis, the volume fraction of recrystallized grains was very low, so dynamic recovery (DRV) is the dominant deformation mechanism of Ti-35421 alloy. In addition to DRV, Ti-35421 alloy is more likely to occur in continuous dynamic recrystallization (CDRX) than discontinuous dynamic recrystallization (DDRX).

scholarly journals Effect of Nitrogen Content on Hot Deformation Behavior and Grain Growth in Nuclear Grade 316LN Stainless Steel

2015 ◽  
Vol 2015 ◽  
pp. 1-8 ◽  
Author(s):  
Ming-wei Guo ◽  
Zhen-hua Wang ◽  
Ze-an Zhou ◽  
Shu-hua Sun ◽  
Wan-tang Fu
Keyword(s):  
Stainless Steel ◽  
Dynamic Recrystallization ◽  
Strain Rate ◽  
Grain Growth ◽  
Strain Rate Sensitivity ◽  
Hot Deformation ◽  
Deformation Behavior ◽  
Rate Sensitivity ◽  
Processing Maps ◽  
Hot Deformation Behavior

316LN stainless steel with 0.08%N (08N) and 0.17%N (17N) was compressed at 1073–1473 K and 0.001–10 s−1. The hot deformation behavior was investigated using stress-strain curve analysis, processing maps, and so forth. The microstructure was analyzed through electron backscatter diffraction analysis. Under most conditions, the deformation resistance of 17N was higher than that of 08N. This difference became more pronounced at lower temperatures. The strain rate sensitivity increased with increasing temperature for types of steel. In addition, the higher the N content, the higher the strain rate sensitivity. Hot deformation activation energy increased from 487 kJ/mol to 549 kJ/mol as N concentration was increased from 0.08% to 0.17%. The critical strain for initiation of dynamic recrystallization was lowered with increasing N content. In the processing maps, both power dissipation ratio and unstable region increased with increasing N concentration. In terms of microstructure evolution, N promoted dynamic recrystallization kinetic and decreased dynamic recrystallization grain size. The grain growth rate was lower in 17N than in 08N during heat treatment. Finally, it was found that N favored twin boundary formation.

Micromechanical Responses of Sn-3.5Ag-xCo Lead-Free Solders by Nanoindentation

2008 ◽  
Vol 580-582 ◽  
pp. 209-212 ◽  
Author(s):  
Feng Gao ◽  
Hiroshi Nishikawa ◽  
Tadashi Takemoto
Keyword(s):  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Rate Sensitivity ◽  
Constant Load ◽  
Lead Free ◽  
Sensitivity Index ◽  
Mechanical Evolution ◽  
Strain Rate Sensitivity Index ◽  
Index Value ◽  
Lead Free Solders

The lead-free casting solders Sn-3.5Ag-xCo (x = 0, 0.1, 0.5 and 1.0 mass%, respectively) were subjected to isothermal aging at 150°C for 0, 1008 and 2016 h, respectively. The nanoindentation methodology was employed herein to assess the mechanical properties. In particular, the strain rate sensitivity index value was derived from the creep deformation at the dwell time of the target constant load using Mayo-Nix theory. Basically, there is no remarkable tendency of the variation of Young’s modulus after aging, while to some extent, the hardness of the alloys drops. The strain rate sensitivity index value continues to decrease with the prolonged aging time. The solder grain growth and the coarsening of the intermetallics namely, Ag3Sn and CoSn2, are responsible for the mechanical evolution of the alloys. The 1.0% (mass%) Co additive improved the hardness of the solder alloy, and caused the decrease of the strain rate sensitivity value.

Theoretical Deduction of Constitutive Equations with Variational Parameters during Superplastic Tension

2014 ◽  
Vol 941-944 ◽  
pp. 1509-1512
Author(s):  
Zhi Ping Guan ◽  
Xiao Fang Guan ◽  
Yu Quan Song
Keyword(s):  
Strain Rate ◽  
Test Data ◽  
Constitutive Equations ◽  
Constant Strain Rate ◽  
Rate Sensitivity ◽  
State Equation ◽  
Sensitivity Index ◽  
Tensile Tester ◽  
Strain Rate Sensitivity Index ◽  
Superplastic Tension

In this article, firstly, the strain hardening index and the strain rate sensitivity index were deducted from the general state equation and the mechanical meaning of the two indexes were correspondingly depicted, and then constitutive equations, where both/either of the two indexes appear as constants, were theoretically deducted from the same state equation. Secondly, constitutive equations where both/either of the two indexes present as variables were put forward by numerical simulation. Next, constitutive equations were built, where mechanical variables are replaced by test data obtained on an electronic universal tensile tester with the capacity to carry out a true constant strain rate path. Finally, based on the test data of Zn-5%Al during superplastic tension, it is proved that the theoretical results in this article are valid.

scholarly journals Characterization of Hot Deformation Behavior and Dislocation Structure Evolution of an Advanced Nickel-Based Superalloy

Metals ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 920 ◽  
Author(s):  
Zhihao Yao ◽  
Hongying Wang ◽  
Jianxin Dong ◽  
Jinglin Wang ◽  
He Jiang ◽  
...  
Keyword(s):  
Dynamic Recrystallization ◽  
Strain Rate ◽  
Hot Deformation ◽  
Deformation Behavior ◽  
Deformation Temperature ◽  
Flow Instability ◽  
Processing Condition ◽  
Constitutive Relationship ◽  
Structure Evolution ◽  
Hot Deformation Behavior

The hot deformation behavior of an advanced nickel-based Haynes282 superalloy was systematically investigated employing isothermal compression tests in the sub-solvus and super-solvus temperature with various strain rates. The influence of deformation temperature and strain rate on the microstructure was studied by transmission electron microscope. The results reveal that the interaction between work hardening and dynamic softening did not reach equilibrium under lower deformation temperature and higher strain rate. The active energy of alloy is around 537.12 kJ/mol and its hot deformation constitutive relationship equation was expressed. According to the processing map and microstructure observations, two unsafe flow instability domains should be avoided. The optimum hot processing condition for homogeneous and fine dynamic recrystallization grains are obtained. TEM micrograph observations indicated that deformation temperature and strain rate affected recrystallization by affecting the evolution of dislocation substructures within the alloy. The nucleation and growth of DRX grains can be promoted by the relatively high deformation temperature and low strain rate. The main mechanism of dynamic recrystallization nucleation preferred to discontinuous dynamic recrystallization and the typical feature of discontinuous dynamic recrystallization showed grain boundary migration nucleation. The findings improve the understanding of hot deformation behavior and dislocation substructures evolution of the superalloy, which benefits the accurate control of microstructures of nickel-based superalloys, and tailors the properties of final components used in the land-based gas turbine.

Sign in / Sign up

Export Citation Format

Share Document