scholarly journals Enhanced Conversion Efficiency of a-Si:H Thin-Film Solar Cell Using ZnO Nanorods

Crystals ◽  
2020 ◽  
Vol 10 (12) ◽  
pp. 1082
Author(s):  
Fang-I Lai ◽  
Jui-Fu Yang ◽  
Yu-Chao Hsu ◽  
Shou-Yi Kuo
Keyword(s):  
Solar Cell ◽  
Conversion Efficiency ◽  
Light Trapping ◽  
Short Circuit ◽  
Zno Nanorods ◽  
Optical Loss ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Zinc Oxide Nanorods ◽  
Surface Reflectivity

The surface reflectivity of a material will vary as light passes through interfaces with different refractive indices. Therefore, the optical loss and reflection of an optical-electronic component can be reduced by fabricating nanostructures on its surface. In the case of a solar cell, the presence of nanostructures can deliver many different advantages, such as decreasing the surface reflectivity, enhancing the light trapping, and increasing the efficiency of the carrier collection by providing a shorter diffusion distance for the photogenerated minority carriers. In this study, an approximately 50-nm thick seed layer was first prepared using spin coating. Zinc oxide nanorods (ZnO-NRs) were then grown using a chemical solution method (CSM). The ZnO-NRs were approximately 2 μm in height and 100 nm in diameter. After applying them to amorphous silicon (a-Si:H) solar cells, the short-circuit current density increased from 8.03 to 9.24 mA/cm2, and the photovoltaic conversion efficiency increased by 11.24%.

scholarly journals Over 30% efficiency bifacial 4-terminal perovskite-heterojunction silicon tandem solar cells with spectral albedo

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Sangho Kim ◽  
Thanh Thuy Trinh ◽  
Jinjoo Park ◽  
Duy Phong Pham ◽  
Sunhwa Lee ◽  
...  
Keyword(s):  
Solar Cell ◽  
Conversion Efficiency ◽  
Crystalline Silicon ◽  
Short Circuit ◽  
Solar Spectrum ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Production Costs ◽  
White Sand ◽  
Reflected Light

AbstractWe developed and designed a bifacial four-terminal perovskite (PVK)/crystalline silicon (c-Si) heterojunction (HJ) tandem solar cell configuration albedo reflection in which the c-Si HJ bottom sub-cell absorbs the solar spectrum from both the front and rear sides (reflected light from the background such as green grass, white sand, red brick, roofing shingle, snow, etc.). Using the albedo reflection and the subsequent short-circuit current density, the conversion efficiency of the PVK-filtered c-Si HJ bottom sub-cell was improved regardless of the PVK top sub-cell properties. This approach achieved a conversion efficiency exceeding 30%, which is higher than those of both the top and bottom sub-cells. Notably, this efficiency is also greater than the Schockley–Quiesser limit of the c-Si solar cell (approximately 29.43%). The proposed approach has the potential to lower industrial solar cell production costs in the near future.

scholarly journals Simulation of a perovskite sandwich solar cell with the p-CZTS / p-CH3NH3PbCI3 / p-CZTS absorber layers

2021 ◽  
Vol 877 (1) ◽  
pp. 012001
Author(s):  
Marwah S Mahmood ◽  
N K Hassan
Keyword(s):  
Solar Cell ◽  
Conversion Efficiency ◽  
Current Density ◽  
Short Circuit ◽  
Perovskite Solar Cells ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Current Voltage ◽  
Cell Capacitance

Abstract Perovskite solar cells attract the attention because of their unique properties in photovoltaic cells. Numerical simulation to the structure of Perovskite on p-CZTS/p-CH3NH3PbCI3/p-CZTS absorber layers is performed by using a program solar cell capacitance simulator (SCAPS-1D), with changing absorber layer thickness. The effect of thickness p-CZTS/p-CH3NH3PbCI3/p-CZTS, layers at (3.2μm, 1.8 μm, 1.1 μm) respectively are studied. The obtained results are short circuit current density (Jsc ), open circuit voltage (V oc), fill factor (F. F) and power conversion efficiency (PCE) equal to (28 mA/cm2, 0.83 v, 60.58 % and 14.25 %) respectively at 1.1 μm thickness. Our findings revealed that the dependence of current - voltage characteristics on the thickness of the absorbing layers, an increase in the amount of short circuit current density with an increase in the thickness of the absorption layers and thus led to an increase in the conversion efficiency and improvement of the cell by increasing the thickness of the absorption layers.

scholarly journals Silicon Substrate Treated with Diluted NaOH Aqueous for Si/PEDOT: PSS Heterojunction Solar Cell with Performance Enhancement

Energies ◽  
2020 ◽  
Vol 13 (18) ◽  
pp. 4659
Author(s):  
Tao Chen ◽  
Hao Guo ◽  
Leiming Yu ◽  
Tao Sun ◽  
Yu Yang
Keyword(s):  
Aqueous Solution ◽  
Solar Cell ◽  
Silicon Substrate ◽  
High Performance ◽  
Immersion Time ◽  
Performance Enhancement ◽  
Light Trapping ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density

Si/PEDOT: PSS solar cell is an important alternative for photovoltaic device due to its anticipated high theoretical efficiency and simple manufacturing process. In this study, processing silicon substrate with diluted NaOH aqueous solution was found to be an effective method for improving device performance, one that notably improves junction quality and light trapping ability. When immersed in diluted NaOH aqueous solution, the junction quality was improved according to the enlarged fill factor, reduced series resistance, and enhanced minor carrier lifetime. The diluted NaOH aqueous solution immersion etched the silicon surface and helped with the enhancement of light trapping ability, further improving the short-circuit current density. Although diluted NaOH aqueous solution immersion for bare silicon could improve the performance of devices, proper immersion time was needed. The influence of immersion time on device performances was investigated. The photovoltaic conversion efficiency easily increased from 10.01% to 12.05% when silicon substrate was immersed in diluted NaOH aqueous for 15 min. This study contributes to providing efficient and convenient methods for preparing high performance Si/PEDOT: PSS solar cells.

Design and modeling of an SJ infrared solar cell approaching upper limit of theoretical efficiency

2018 ◽  
Vol 32 (02) ◽  
pp. 1850014 ◽  
Author(s):  
G. S. Sahoo ◽  
G. P. Mishra
Keyword(s):  
Solar Cell ◽  
Quantum Efficiency ◽  
Conversion Efficiency ◽  
Internal Quantum Efficiency ◽  
Spectral Response ◽  
Short Circuit ◽  
Cost Effective ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit

Recent trends of photovoltaics account for the conversion efficiency limit making them more cost effective. To achieve this we have to leave the golden era of silicon cell and make a path towards III–V compound semiconductor groups to take advantages like bandgap engineering by alloying these compounds. In this work we have used a low bandgap GaSb material and designed a single junction (SJ) cell with a conversion efficiency of 32.98%. SILVACO ATLAS TCAD simulator has been used to simulate the proposed model using both Ray Tracing and Transfer Matrix Method (under 1 sun and 1000 sun of AM1.5G spectrum). A detailed analyses of photogeneration rate, spectral response, potential developed, external quantum efficiency (EQE), internal quantum efficiency (IQE), short-circuit current density (J[Formula: see text]), open-circuit voltage (V[Formula: see text]), fill factor (FF) and conversion efficiency ([Formula: see text]) are discussed. The obtained results are compared with previously reported SJ solar cell reports.

CHARACTERISTICS OF PHOSPHORUS-DOPED AMORPHOUS CARBON FILMS GROWN BY R. F. PLASMA-ENHANCED CVD WITH A NOVEL PHOSPHORUS SOLID TARGET

2005 ◽  
Vol 12 (01) ◽  
pp. 19-25 ◽  
Author(s):  
M. RUSOP ◽  
M. ADACHI ◽  
T. SOGA ◽  
T. JIMBO
Keyword(s):  
Solar Cell ◽  
Conversion Efficiency ◽  
Amorphous Carbon ◽  
Current Density ◽  
Fill Factor ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Phosphorus Doped

Phosphorus-doped amorphous carbon (n-C:P) films were grown by r. f.-power-assisted plasma-enhanced chemical vapor deposition at room temperature using a novel solid red phosphorus target. The influence of phosphorus doping on material properties of n-C:P based on the results of simultaneous characterization are reported. Moreover, the solar cell properties such as series resistance, short circuit current density, open circuit current voltage, fill factor and conversion efficiency along with the spectral response are reported for the fabricated carbon-based n-C:P/p-Si heterojunction solar cell that was measured by standard measurement technique. The cells performances have been given in the dark I–V rectifying curve and I–V working curve under illumination when exposed to AM 1.5 illumination condition (100 mW/cm 2, 25°C). The maximum of open-circuit voltage (V oc ) and short-circuit current density (J sc ) for the cells are observed to be approximately 236 V and 7.34, mAcm 2 respectively for the n-C:P/p-Si cell grown at lower r. f. power of 100 W. The highest energy conversion efficiency (η) and fill factor (FF) were found to be approximately 0.84% and 49%, respectively. We have observed that the rectifying nature of the heterojunction structures is due to the nature of n-C:P films.

scholarly journals Novel Photonic Crystal Based Polycrystalline CdTe/Silicon Solar Cells

2020 ◽  
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Photonic Crystal ◽  
Conversion Efficiency ◽  
Current Density ◽  
Cell Structure ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Silicon Solar Cells

In this paper, a novel photonic crystal (PhC) polycrystalline CdTe/Silicon solar cells are theoretically explained that increase their short circuit current density and conversion efficiency. The proposed structure consist of a polycrystalline CdTe/Silicon solar cell that a photonic crystal is formed in the upper cell. The optical confinement is achieved by means of photonic crystal that can adjust the propagation and distribution of photons in solar cells. For validation of modeling, the electrical properties of the experimentally-fabricated based CdS/CdTe solar cell is modeled and compared that there is good agreement between the modeling results and experimental results from the litterature. The results of this study showed that the solar cell efficiency is increased by about 25% compared to the reference cell by using photonic crystal. The open circuit voltage, short circuit current density, fill factor and conversion efficiency of proposed solar cell structure are 1.01 V, 40.7 mA/cm2, 0.95 and 27% under global AM 1.5 conditions, respectively. Furthermore, the influence of carrier lifetime variation in the absorber layer of proposed solar cell on the electrical characteristics was theoretically considered and investigated.

scholarly journals Numerical study of a highly efficient light trapping nanostructure of perovskite solar cell on a textured silicon substrate

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Alireza Tooghi ◽  
Davood Fathi ◽  
Mehdi Eskandari
Keyword(s):  
Solar Cell ◽  
Silicon Substrate ◽  
Numerical Study ◽  
Light Trapping ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Perovskite Solar Cell ◽  
Short Circuit Current Density ◽  
Planar Structure ◽  
Plasmonic Enhancement

Abstract In this paper, a nanostructured perovskite solar cell (PSC) on a textured silicon substrate is examined, and its performance is analyzed. First, its configuration and the simulated unit cell are discussed, and its fabrication method is explained. In this proposed structure, poly-dimethylsiloxane (PDMS) is used instead of glass. It is shown that the use of PDMS dramatically reduces the reflection from the cell surface. Furthermore, the light absorption is found to be greatly increased due to the light trapping and plasmonic enhancement of the electric field in the active layer. Then, three different structures, are compared with the main proposed structure in terms of absorption, considering the imperfect fabrication conditions and the characteristics of the built PSC. The findings show that in the worst fabrication conditions considered structure (FCCS), short-circuit current density (Jsc) is 22.28 mA/cm2, which is 27% higher than that of the planar structure with a value of 17.51 mA/cm2. As a result, the efficiencies of these FCCSs are significant as well. In the main proposed structure, the power conversion efficiency (PCE) is observed to be improved by 32%, from 13.86% for the planar structure to 18.29%.

A Study on Optical and Electrical Properties of Solar Cells of a-Si1-XGeX:H

2011 ◽  
Vol 347-353 ◽  
pp. 3666-3669
Author(s):  
Ming Biao Li ◽  
Li Bin Shi
Keyword(s):  
Solar Cell ◽  
Electrical Properties ◽  
Conversion Efficiency ◽  
Fill Factor ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Optical And Electrical Properties

The AMPS-ID program is used to investigate optical and electrical properties of the solar cell of a-SiC:H/a-Si1-xGex:H/a-Si:H thin films. The short circuit current density, open circuit voltage, fill factor and conversion efficiency of the solar cell are investigated. For x=0.1, the conversion efficiency of the solar cell achieve maximum 9.19 % at the a-Si1-xGex:H thickness of 340 nm.

Fabrication and Characterization of Dye-Sensitized Solar Cell with Different Microstructure ZnO

2010 ◽  
Vol 663-665 ◽  
pp. 857-860 ◽  
Author(s):  
Yan Xiang Wang ◽  
Ting Li Ma ◽  
Xue Yun Fan ◽  
Xiao Yan Li
Keyword(s):  
Solar Cell ◽  
Conversion Efficiency ◽  
Zno Nanoparticles ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Energy Conversion Efficiency ◽  
Short Circuit Current Density ◽  
Dye Sensitized Solar Cell ◽  
Dye Sensitized ◽  
Size And Morphology

In order to improve the performance of the dye-sensitized solar cells based on ZnO films, ZnO nanoparticles of different size and morphology were prepared by hydrothermal and solvothermal synthesis methods. Electrodes applied to dye-sensitized solar cell were prepared by the screen-printing method. The effects of ZnO nanoparticles of different size and morphology on the photovoltaic characteristics of dye-sensitized ZnO solar cells were investigated. The results show that: The short-circuit current density and the energy conversion efficiency of the ZnO nanosheets DSSC are 0.13 mA/cm2 and 0.02%. The short-circuit current density and the energy conversion efficiency of cells prepared with ZnO nanorods with diameter 500nm and length 5μm are 1.91 mA/cm2 and 0.03%.The best performance achieved in the present work was a conversion efficiency of 3.46% for the cells prepared with ZnO nanoparticles with diameters 80nm.

Sign in / Sign up

Export Citation Format

Share Document