scholarly journals Precipitated K-Promoted Co–Mn–Al Mixed Oxides for Direct NO Decomposition: Preparation and Properties

Catalysts ◽  
2019 ◽  
Vol 9 (7) ◽  
pp. 592 ◽  
Author(s):  
Květa Jirátová ◽  
Kateřina Pacultová ◽  
Jana Balabánová ◽  
Kateřina Karásková ◽  
Anna Klegová ◽  
...  
Keyword(s):  
Catalytic Activity ◽  
Mixed Oxides ◽  
No Decomposition ◽  
Temperature Programmed Reduction ◽  
X Ray ◽  
Co2 Desorption ◽  
Metal Nitrates ◽  
Temperature Programmed ◽  
Desorption Method ◽  
Al Oxide

Direct decomposition of nitric oxide (NO) proceeds over Co–Mn–Al mixed oxides promoted by potassium. In this study, answers to the following questions have been searched: Do the properties of the K-promoted Co–Mn–Al catalysts prepared by different methods differ from each other? The K-precipitated Co–Mn–Al oxide catalysts were prepared by the precipitation of metal nitrates with a solution of K2CO3/KOH, followed by the washing of the precipitate to different degrees of residual K amounts, and by cthe alcination of the precursors at 500 °C. The properties of the prepared catalysts were compared with those of the best catalyst prepared by the K-impregnation of a wet cake of Co–Mn–Al oxide precursors. The solids were characterized by chemical analysis, DTG, XRD, N2 physisorption, FTIR, temperature programmed reduction (H2-TPR), temperature programmed CO2 desorption (CO2-TPD), X-ray photoelectron spectrometry (XPS), and the species-resolved thermal alkali desorption method (SR-TAD). The washing of the K-precipitated cake resulted in decreasing the K amount in the solid, which affected the basicity, reducibility, and non-linearly catalytic activity in NO decomposition. The highest activity was found at ca 8 wt.% of K, while that of the best K-impregnated wet cake catalyst was at about 2 wt.% of K. The optimization of the cake washing conditions led to a higher catalytic activity.

scholarly journals Magnesium Effect in K/Co-Mg-Mn-Al Mixed Oxide Catalyst for Direct NO Decomposition

Catalysts ◽  
2020 ◽  
Vol 10 (8) ◽  
pp. 931
Author(s):  
Kateřina Karásková ◽  
Kateřina Pacultová ◽  
Anna Klegova ◽  
Dagmar Fridrichová ◽  
Marta Valášková ◽  
...  
Keyword(s):  
Mixed Oxide ◽  
Thermal Instability ◽  
Mixed Oxides ◽  
No Decomposition ◽  
Molar Ratio ◽  
Partial Substitution ◽  
X Ray ◽  
Mixed Oxide Catalyst ◽  
Temperature Programmed ◽  
Activity Decrease

Emission of nitric oxide represents a serious environmental problem since it contributes to the formation of acid rain and photochemical smog. Potassium-modified Co-Mn-Al mixed oxide is an effective catalyst for NO decomposition. However, there are problems related to the thermal instability of potassium species and a high content of toxic and expensive cobalt. The reported research aimed to determine whether these shortcomings can be overcome by replacing cobalt with magnesium. Therefore, a series of Co-Mg-Mn-Al mixed oxides with different Co/Mg molar ratio and promoted by various content of potassium was investigated. The catalysts were thoroughly characterized by atomic absorption spectroscopy (AAS), temperature-programmed reduction by hydrogen (TPR-H2), temperature-programmed desorption of CO2 (TPD-CO2), X-ray powder diffraction (XRD), N2 physisorption, species-resolved thermal alkali desorption (SR-TAD), and tested in direct NO decomposition with and without the addition of oxygen and water vapor. Partial substitution of magnesium for cobalt did not cause an activity decrease when the optimal molar ratio of K/Co on the normalized surface area was maintained; it means that the portion of expensive and toxic cobalt can be successfully replaced by magnesium without any decrease in catalytic activity.

Hydrogen Adsorption Capacity Investigation of Ni-Co-Al Mixed Oxides

2014 ◽  
Vol 917 ◽  
pp. 360-364 ◽  
Author(s):  
M. Abdus Salam ◽  
Suriati Sufian
Keyword(s):  
Hydrogen Adsorption ◽  
Mixed Oxides ◽  
Textural Properties ◽  
Metal Dispersion ◽  
Temperature Programmed Reduction ◽  
Oxide Formation ◽  
Nickel Cobalt ◽  
Icp Ms ◽  
Temperature Programmed ◽  
Adsorption Desorption

Micro-mesoporous mixed oxides containing nickel, cobalt and aluminum have been synthesized using conventional coprecipitation method. FESEM and HRTEM analyses demonstrated the flower and hexagonal plate-like nanostructured of mixed oxides. Different mixed oxide formation, homogenous metal dispersion, textural properties were investigated using XRD, ICP-MS and BET (N2 adsorption-desorption) techniques. nanostructured mixed oxides exhibited 2.6 wt% hydrogen adsorption that were studied using temperature programmed reduction-adsorption-desorption (H2-TPR/TPD) and thermogravimetric and differential thermal analysis (TGA-DTA) techniques. Investigation corresponds that morphologies, textural properties and surface energy of mixed oxides are important in hydrogen adsorption.

scholarly journals Copper-Containing Mixed Metal Oxides (Al, Fe, Mn) for Application in Three-Way Catalysis

Catalysts ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 1344
Author(s):  
Tim Van Everbroeck ◽  
Radu-George Ciocarlan ◽  
Wouter Van Hoey ◽  
Myrjam Mertens ◽  
Pegie Cool
Keyword(s):  
Catalytic Activity ◽  
Spinel Structure ◽  
Mixed Oxides ◽  
High Catalytic Activity ◽  
X Ray Diffraction ◽  
X Ray ◽  
Catalytic Application ◽  
Mixed Spinel ◽  
Co Precipitation ◽  
Three Way Catalysis

Mixed oxides were synthesized by co-precipitation of a Cu source in combination with Al, Fe or Mn corresponding salts as precursors. The materials were calcined at 600 and 1000 °C in order to crystallize the phases and to mimic the reaction conditions of the catalytic application. At 600 °C a mixed spinel structure was only formed for the combination of Cu and Mn, while at 1000 °C all the materials showed mixed spinel formation. The catalysts were applied in three-way catalysis using a reactor with a gas mixture containing CO, NO and O2. All the materials calcined at 600 °C displayed the remarkable ability to oxidize CO with O2 but also to reduce NO with CO, while the pure oxides such as CuO and MnO2 were not able to. The high catalytic activity at 600 °C was attributed to small supported CuO particles present and imperfections in the spinel structure. Calcination at 1000 °C crystallized the structure further which led to a dramatic loss in catalytic activity, although CuAl2O4 and CuFe2O4 still converted some NO. The materials were characterized by X-ray diffraction (XRD), Raman spectroscopy, H2-Temperatrue Programmed Reduction (H2-TPR), N2-sorption and scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDX).

scholarly journals Bulk Versus Surface Modification of Alumina with Mn and Ce Based Oxides for CH4 Catalytic Combustion

Materials ◽  
2019 ◽  
Vol 12 (11) ◽  
pp. 1771 ◽  
Author(s):  
Stefan Neatu ◽  
Mihaela M. Trandafir ◽  
Adelina Stănoiu ◽  
Ovidiu G. Florea ◽  
Cristian E. Simion ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Catalytic Combustion ◽  
Mixed Oxides ◽  
Sol Gel ◽  
Nitrogen Adsorption ◽  
X Ray Diffraction ◽  
X Ray ◽  
Temperature Programmed ◽  
Catalytic Combustion Of Methane ◽  
Adsorption Desorption

This study presents the synthesis and characterization of lanthanum-modified alumina supported cerium–manganese mixed oxides, which were prepared by three different methods (coprecipitation, impregnation and citrate-based sol-gel method) followed by calcination at 500 °C. The physicochemical properties of the synthesized materials were investigated by various characterization techniques, namely: nitrogen adsorption-desorption isotherms, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and H2–temperature programmed reduction (TPR). This experimental study demonstrated that the role of the catalytic surface is much more important than the bulk one. Indeed, the incipient impregnation of CeO2–MnOx catalyst, supported on an optimized amount of 4 wt.% La2O3–Al2O3, provided the best results of the catalytic combustion of methane on our catalytic micro-convertors. This is mainly due to: (i) the highest pore size dimensions according to the Brunauer-Emmett-Teller (BET) investigations, (ii) the highest amount of Mn4+ or/and Ce4+ on the surface as revealed by XPS, (iii) the presence of a mixed phase (Ce2MnO6) as shown by X-ray diffraction; and (iv) a higher reducibility of Mn4+ or/and Ce4+ species as displayed by H2–TPR and therefore more reactive oxygen species.

scholarly journals “PdO vs. PtO”—The Influence of PGM Oxide Promotion of Co3O4 Spinel on Direct NO Decomposition Activity

Catalysts ◽  
2019 ◽  
Vol 9 (1) ◽  
pp. 62 ◽  
Author(s):  
Gunugunuri K. Reddy ◽  
Torin C. Peck ◽  
Charles A. Roberts
Keyword(s):  
Photoelectron Spectroscopy ◽  
No Decomposition ◽  
Single Element ◽  
X Ray Diffraction ◽  
X Ray ◽  
Promotional Effect ◽  
Ft Ir ◽  
Temperature Programmed ◽  
Thermal Stability Of

Direct decomposition of NO into N2 and O2 (2NO→N2 + O2) is recognized as the “ideal” reaction for NOx removal because it needs no reductant. It was reported that the spinel Co3O4 is one of the most active single-element oxide catalysts for NO decomposition at higher reaction temperatures, however, activity remains low below 650 °C. The present study aims to investigate new promoters for Co3O4, specifically PdO vs. PtO. Interestingly, the PdO promoter effect on Co3O4 was much greater than the PtO effect, yielding a 4 times higher activity for direct NO decomposition at 650 °C. Also, Co3O4 catalysts with the PdO promoter exhibit higher selectivity to N2 compared to PtO/Co3O4 catalysts. Several characterization measurements, including X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), H2-temperature programmed reduction (H2-TPR), and in situ FT-IR, were performed to understand the effect of PdO vs. PtO on the properties of Co3O4. Structural and surface analysis measurements show that impregnation of PdO on Co3O4 leads to a greater ease of reduction of the catalysts and an increased thermal stability of surface adsorbed NOx species, which contribute to promotion of direct NO decomposition activity. In contrast, rather than remaining solely as a surface species, PtO enters the Co3O4 structure, and it promotes neither redox properties nor NO adsorption properties of Co3O4, resulting in a diminished promotional effect compared to PdO.

Oxygen Radicals Occlusion/Release Behavior of Nanoporous Aluminosilicate, Ca12Al14-XSiXO33+0.5X (0≦X≦4)

2006 ◽  
Vol 45 ◽  
pp. 2105-2109
Author(s):  
Makoto Nagashima ◽  
Daisuke Hirabayashi ◽  
Kenzi Suzuki
Keyword(s):  
Catalytic Activity ◽  
Oxygen Content ◽  
Oxygen Radicals ◽  
Catalytic Performance ◽  
Oxygen Release ◽  
Release Behavior ◽  
Temperature Programmed Reduction ◽  
Temperature Programmed Oxidation ◽  
Temperature Range ◽  
Temperature Programmed

Oxygen radicals occlusion / release behavior of nanoporous aluminosilicate, Ca12Al14-XSiXO33+0.5X (0≦X≦4), synthesized under different condition was examined by the temperature programmed reduction (TPR) in an atmosphere of hydrogen in the temperature range of 200-1000°C and temperature programmed oxidation (TPO) measurement at 800°C. From the TPR results of Ca12Al14O33 (X=0) and Ca12Al10Si4O35 (X=4), it was found that there were three oxygen release peaks, denoted as α, β and γ, on each sample and the peaks appeared in the temperature range 300-420°C, 420-600°C, and 600-750°C, respectively. The oxygen contents of α and γ of samples were almost the same. However, the oxygen content of β in the sample with x = 4 was much larger, almost double, compared to that in x = 0. From the TPR, TPO results and catalytic performance, it was concluded that the oxygen content of β peak strongly influenced the catalytic activity of the nanoporous aluminosilicate in the propylene combustion.

Reduction of Molybdenum Trioxide by Using Hydrogen

2017 ◽  
Vol 888 ◽  
pp. 404-408 ◽  
Author(s):  
Mohd Nor Latif ◽  
Alinda Samsuri ◽  
Mohamed Wahab Mohamed Hisham ◽  
Mohd Ambar Yarmo
Keyword(s):  
Molybdenum Trioxide ◽  
Reduction Step ◽  
Temperature Programmed Reduction ◽  
X Ray Diffraction ◽  
Thermodynamic Consideration ◽  
Rapid Reduction ◽  
Reduction Behavior ◽  
X Ray ◽  
Intermediate Phases ◽  
Temperature Programmed

Metallic molybdenum was synthesized through reduction of molybdenum trioxide (MoO3) by using hydrogen as a reducing agent. The reduction behavior of MoO3 were investigated by using temperature programmed reduction (TPR). The reduced phases were characterized by X-ray diffraction spectroscopy (XRD). The XRD results indicate that the reduction of MoO3 proceed in two steps reduction (MoO3 → MoO2 → Mo) with formation of intermediate phases of Mo4O11 during first step of reduction. However, the TPR results showed only one broad peak that correspond to all reduction step that was merge into one peak. It seem that, increasing the temperature cause the rapid reduction that correlated with thermodynamic consideration data that show the formation of metallic molybdenum is become feasible by increasing the temperature.

Au/iron oxide catalysts: temperature programmed reduction and X-ray diffraction characterization

1999 ◽  
Vol 329 (1) ◽  
pp. 39-46 ◽  
Author(s):  
G Neri ◽  
A.M Visco ◽  
S Galvagno ◽  
A Donato ◽  
M Panzalorto
Keyword(s):  
Iron Oxide ◽  
Oxide Catalysts ◽  
Temperature Programmed Reduction ◽  
X Ray Diffraction ◽  
X Ray ◽  
Temperature Programmed

Promotion Effects of La2O3 on Ni/Al2O3 Catalysts for CO2 Methanation

2015 ◽  
Vol 1118 ◽  
pp. 205-210 ◽  
Author(s):  
Wei Chang Chen ◽  
Wen Yang ◽  
Jian Dong Xing ◽  
Lei Liu ◽  
Hong Li Sun ◽  
...  
Keyword(s):  
Particle Size ◽  
Impregnation Method ◽  
Temperature Programmed Reduction ◽  
Active Components ◽  
X Ray ◽  
Induce Effect ◽  
Temperature Programmed ◽  
Ni Species ◽  
Adsorption Desorption ◽  
Catalytic Performances

Ni/Al2O3catalysts improved with different La contents were prepared by the conventional co-impregnation method and characterized by X-ray powder diffraction (XRD), N2adsorption-desorption, H2temperature-programmed reduction (H2-TPR). Catalytic performances for CO2methanation under condition (CO2/H2=4.1:1, 1 atm) were discussed in detail. XRD result demonstrated that the addition of La was in favor of decreasing the Ni particle size and increasing the dispersion of Ni species. The H2-TPR showed that La can change the proportion of various Ni species and increase the content of easily reducible Ni species. These results indicate that La species induce effect, resulting in smaller particle size and weaker interaction between active components and the support, higher dispersions, and reducibility of active phases, ultimately improving catalytic activity of CO2methanation.

Sign in / Sign up

Export Citation Format

Share Document