scholarly journals Evolution of Copper Supported on Fe3O4 Nanorods for WGS Reaction

Catalysts ◽  
2018 ◽  
Vol 8 (10) ◽  
pp. 415 ◽  
Author(s):  
Lingjuan Ma ◽  
Hongbin Ma ◽  
Dawei Han ◽  
Mingyue Qiu ◽  
Yafei Guan ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Ambient Pressure ◽  
Phase Evolution ◽  
Precipitation Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
In Situ Xrd ◽  
Wgs Reaction ◽  
Transmission Electron ◽  
Temperature Programmed

Rod-shaped Cu1Fe9Ox precursor was successfully prepared through an aqueous precipitation method. The shape and phase composition were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). It was found that Cu1Fe9Ox is composed of CuFe2O4 and Fe2O3. The reduction performance of Cu1Fe9Ox was studied by in situ XRD and H2 temperature-programmed reduction (H2-TPR). Cu/Fe3O4 nanorod catalyst is obtained through the controllable reduction of Cu1Fe9Ox nanorod, and the formed Cu/Fe3O4 nanorod catalyst does not have low-temperature water gas shift (WGS) activity, but exhibits high-temperature WGS reaction activity. Ambient pressure X-ray photoelectron spectroscopy (AP-XPS) studies showed that the main species of copper is Cu+ during the WGS reaction. The interaction between Cu and Fe3O4 rod and phase evolution of Cu species are quite different from Cu/Fe3O4 nanoparticles.

scholarly journals Nanosized V-Ce Oxides Supported on TiO2 as a Superior Catalyst for the Selective Catalytic Reduction of NO

Catalysts ◽  
2020 ◽  
Vol 10 (2) ◽  
pp. 202
Author(s):  
Long Lu ◽  
Xueman Wang ◽  
Chunhua Hu ◽  
Ying Liu ◽  
Xiongbo Chen ◽  
...  
Keyword(s):  
Low Temperature ◽  
Selective Catalytic Reduction ◽  
Photoelectron Spectroscopy ◽  
Catalytic Reduction ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Redox Capacity ◽  
Scr Of No ◽  
Temperature Programmed

Nanosized V-Ce oxides supported on TiO2 (VCT) were prepared and utilized in the low-temperature selective catalytic reduction (SCR) of NO with NH3. Compared with the other V-Ce oxides-based catalysts supported on Al2O3, ZrO2, and ZSM-5, VCT showed the best SCR activity in a low-temperature range. The NOx conversion of 90% could be achieved at 220 °C. Characterizations including X-ray diffraction (XRD), scanning election micrograph (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), temperature-programmed desorption with NH3 (NH3-TPD), and temperature-programmed reduction with H2 (H2-TPR) showed that V1.05Ce1/TiO2 exhibited a good dispersion of V2O5, enrichment of surface Ce3+ and chemical-absorbed oxygen, and excellent redox capacity and acidity, which resulted in the best SCR performance at low temperature.

scholarly journals High Active Co/Mg1-xCex3+O Catalyst: Effects of Metal-Support Promoter Interactions on CO2 Reforming of CH4 Reaction

2021 ◽  
Vol 16 (1) ◽  
pp. 97-110
Author(s):  
Faris A. Jassim Al-Doghachi ◽  
Diyar M. A. Murad ◽  
Huda S. Al-Niaeem ◽  
Salam H. H. Al-Jaberi ◽  
Surahim Mohamad ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Fixed Bed ◽  
Fixed Bed Reactor ◽  
Dry Reforming Of Methane ◽  
Precipitation Method ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Co2 Reforming Of Ch4 ◽  
Temperature Programmed

Co/Mg1−XCe3+XO (x = 0, 0.03, 0.07, 0.15; 1 wt% cobalt each) catalysts for the dry reforming of methane (DRM) reaction were prepared using the co-precipitation method with K2CO3 as precipitant. Characterization of the catalysts was achieved by X-ray diffraction (XRD), X-ray fluorescence spectroscopy (XRF), X-ray photoelectron spectroscopy (XPS), temperature programmed reduction (H2-TPR), Brunauer–Emmett–Teller (BET), transmission electron microscopy (TEM), and thermal gravimetric analysis (TGA). The role of several reactant and catalyst concentrations, and reaction temperatures (700–900 °C) on the catalytic performance of the DRM reaction was measured in a tubular fixed-bed reactor under atmospheric pressure at various CH4/CO2 concentration ratios (1:1 to 2:1). Using X-ray diffraction, a surface area of 19.2 m2.g−1 was exhibited by the Co/Mg0.85Ce3+0.15O catalyst and MgO phase (average crystallite size of 61.4 nm) was detected on the surface of the catalyst. H2 temperature programmed reaction revealed a reduction of CoO particles to metallic Co0 phase. The catalytic stability of the Co/Mg0.85Ce3+0.15O catalyst was achieved for 200 h on-stream at 900 °C for the 1:1 CH4:CO2 ratio with an H2/CO ratio of 1.0 and a CH4, CO2 conversions of 75% and 86%, respectively. In the present study, the conversion of CH4 was improved (75%–84%) when conducting the experiment at a lower flow of oxygen (1.25%). Finally, the deposition of carbon on the spent catalysts was analyzed using TEM and Temperature programmed oxidation-mass spectroscopy (TPO-MS) following 200 h under an oxygen stream. Better anti-coking activity of the reduced catalyst was observed by both, TEM, and TPO-MS analysis. Copyright © 2021 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA   License (https://creativecommons.org/licenses/by-sa/4.0). 

Study on photocatalytic activity based on different pH values of AgBr/Ag2CO3 heterojunction

2020 ◽  
Vol 111 (10) ◽  
pp. 842-848
Author(s):  
Fengfeng Li ◽  
Mingxi Zhang ◽  
Jin Wang ◽  
Yongfeng Cai ◽  
Dushao Zhao ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Rhodamine B ◽  
Photoelectron Spectroscopy ◽  
Precipitation Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Photocatalytic Activities ◽  
Co Precipitation ◽  
Degradation Degree

Abstract In this work, we fabricate a highly efficient photocatalytic AgBr/Ag2CO3 heterojunction through the co-precipitation method. The obtained samples were characterized by means of X-ray diffraction, scanning electron microscopy, transmission electron microscopy, ultraviolet-visible diffuse reflectance spectra and X-ray photoelectron spectroscopy. The photocatalytic activities of obtained samples can be assessed by visible light (λ ≥ 400 nm) degradation of rhodamine B solution. X-ray diffraction revealed that the crystallinity of the AgBr/Ag2CO3heterojunction was significantly higher than pure AgBr and Ag2CO3. Moreover, the AgBr/ Ag2CO3 heterojunction prepared at pH = 6 has the best photocatalytic performance, it can raise the degradation degree of rhodamine B over 95% at 20 min. Finally, a possible photocatalytic mechanism is discussed.

Pd-Only Catalyst Modified by BaO with Co- Precipitation and Impregnation Methods towards the Methanol Fuel Emission Control

2012 ◽  
Vol 581-582 ◽  
pp. 313-316
Author(s):  
Xue Qiao Zhang ◽  
Zhi Xiang Ye ◽  
Cheng Hua Xu ◽  
Ming Zhao ◽  
Yao Qiang Chen
Keyword(s):  
Co Oxidation ◽  
Photoelectron Spectroscopy ◽  
Palladium Catalysts ◽  
Active Species ◽  
Precipitation Method ◽  
Impregnation Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Temperature Programmed ◽  
Co Precipitation

Barium oxide was introduced to modify Palladium catalysts supported on CeO2–ZrO2-La2O3-Al2O3 (CZLA) by impregnation and co-precipitation. methods. Various techniques, including X-ray diffraction (XRD), H2-temperature-programmed reduction (H2-TPR) and X-ray photoelectron spectroscopy (XPS), were employed to characterize the physicochemical properties of BaO-modified Pd-only catalyst. Catalytic activity for methanol, CO, C3H8 and NO conversions showed that BaO-modified catalyst prepared by impregnation method exhibited the best performance for methanol, C3H8 and NO removals, while the catalyst prepared by co-precipitation method was in favor of CO oxidation. Combined with the results of XRD, H2-TPR and XPS, it is concluded that the co-existence of PdO and Pd-O-Ce active species by impregnation played an important role in the methanol, C3H8 and NO removals, while the higher dispersion of palladium and improved reducibility were mostly favorable to the CO oxidation. The conversion of NO was co-effected by tow active species and the formation of Ba2AlLaO5 mixed oxide.

scholarly journals Heterogeneous catalytic ozonation of hydroquinone using sewage sludge-derived carbonaceous catalysts

2018 ◽  
Vol 77 (5) ◽  
pp. 1410-1417 ◽  
Author(s):  
Jinglu Xu ◽  
Yang Yu ◽  
Kang Ding ◽  
Zhiying Liu ◽  
Lei Wang ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Sewage Sludge ◽  
Photoelectron Spectroscopy ◽  
Removal Rate ◽  
Gas Chromatography Mass Spectrometry ◽  
X Ray Diffraction ◽  
X Ray ◽  
Heterogeneous Catalytic ◽  
Transmission Electron ◽  
Temperature Programmed

Abstract This study converted sewage sludge into a carbonaceous catalyst via pyrolysis and employed it in the ozonation of hydroquinone. The catalyst was characterized by Mössbauer spectroscopy, X-ray photoelectron spectroscopy, temperature programmed desorption, scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectroscopy and X-ray diffraction. Intermediate products were detected by gas chromatography–mass spectrometry, and a pathway for hydroquinone degradation was proposed. The results showed that sludge pyrolyzed at 700 °C promoted hydroquinone degradation, compared with commercial activated carbon derived from coal. When the catalyst dose was 0.5 g/L, the hydroquinone (200 mg/L) removal rate reached 97.86% after exposure to ozone (the ozone concentration was 17 mg/L and the flow rate was 50 mL/min) for 60 min. The results indicated that basic groups contributed to the catalysis.

scholarly journals Characterization of Highly Dispersed Rod- and Particle-Shaped CuFe19Ox Catalysts and Their Shape Effects on WGS

Catalysts ◽  
2018 ◽  
Vol 8 (12) ◽  
pp. 635
Author(s):  
Lingjuan Ma ◽  
Dawei Han ◽  
Hongbin Ma ◽  
Longgang Liu ◽  
Huichao Guo
Keyword(s):  
X Ray Diffraction ◽  
X Ray ◽  
In Situ Xrd ◽  
Transmission Electron ◽  
Highly Dispersed ◽  
Shape Effects ◽  
Temperature Programmed ◽  
Water Gas

Highly dispersed CuFe19Ox catalysts with different shapes were prepared and further characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), H2 temperature-programmed reduction (H2-TPR), and in-situ XRD. XRD and TEM results showed that the synthesized CuFe19Ox nanoparticles consisted of CuO and Fe2O3, while CuFe19Ox nanorods consisted of CuFe2O4 and Fe2O3. The reduction properties of CuFe19Ox samples were finely studied by H2-TPR, and the phase composition was identified by in-situ XPS, HR-TEM, and surface TPR (s-TPR). In-situ X-ray photoelectroscopy (XPS) indicated that the metallic Cu and Fe3O4 were the main species after reduction. Moreover, s-TPR studies showed that the reduction performance of copper was significantly affected by the shapes of the Fe3O4 supports. Low-temperature water gas shift (LT-WGS) was chosen to characterize the Cu species on the surface. It was found that reduced CuFe19Ox nanorods had no activity. On the contrary, reduced CuFe19Ox particles showed higher initial WGS activity, where the active Cu0 should originate from the reduction of Cu2O at lower temperatures, as confirmed by the s-TPR profiles.

scholarly journals Synthesis and Catalytic Performance of Ni/SiO2for Hydrogenation of 2-Methylfuran to 2-Methyltetrahydrofuran

2015 ◽  
Vol 2015 ◽  
pp. 1-6 ◽  
Author(s):  
Fu Ding ◽  
Yajing Zhang ◽  
Guijin Yuan ◽  
Kangjun Wang ◽  
Ileana Dragutan ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
Catalytic Performance ◽  
Bet Surface Area ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ni Content ◽  
Transmission Electron ◽  
Temperature Programmed ◽  
Ni Species

A series of Ni/SiO2catalysts with different Ni content were prepared by sol-gel method for application in the synthesis of 2-methyltetrahydrofuran (2-MTHF) by hydrogenation of 2-methylfuran (2-MF). The catalyst structure was investigated by X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and temperature programmed reduction (TPR). It is found that structures and catalytic performance of the catalysts were highly affected by the Ni content. The catalyst with a 25% Ni content had an appropriate size of the Ni species and larger BET surface area and produced a higher 2-MF conversion with enhanced selectivity in 2-MTHF.

Improvement of physico-chemical properties by addition of H2O2: An extensive case study on the RE-doped ceria system (RE = Gd, Sm)

2009 ◽  
Vol 24 (9) ◽  
pp. 2845-2854 ◽  
Author(s):  
Balaji P. Mandal ◽  
Vinita Grover ◽  
Mrinal R. Pai ◽  
Avesh K. Tyagi
Keyword(s):  
Surface Area ◽  
Photoelectron Spectroscopy ◽  
Chemical Properties ◽  
Doped Ceria ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Physico Chemical ◽  
Powder Properties ◽  
Temperature Programmed

Effect of H2O2 on synthesis and powder properties such as surface area and agglomerate size of nanocrystalline Ce0.8M0.2O1.90 (M: Sm, Gd) was explored by treating cerium nitrate and rare-earth nitrate with NaOH in the presence/absence of H2O2. The resultant products were characterized by x-ray diffraction, Raman spectroscopy, thermo-gravimetry–differential thermal analysis, dynamic light scattering, surface area analysis, high-resolution transmission electron microscopy, and x-ray photoelectron spectroscopy. The presence of H2O2 was found to have a profound effect on powder properties such as surface area and particle size of these doped ceria samples and results in smaller crystallite size, softer agglomerates, and larger surface area. A mechanism is proposed to explain the observed better powder properties of the samples. It was also shown that the samples prepared in the presence of H2O2 can lower the conversion temperature of CO to CO2, proving these to be better catalysts. Interestingly, temperature-programmed reduction studies on Sm3+-doped samples showed that the doping in conjunction with the use of H2O2 leads to enhanced reduction properties of the samples over multiple cycles.

scholarly journals α-Cellulose Fibers of Paper-Waste Origin Surface-Modified with Fe3O4 and Thiolated-Chitosan for Efficacious Immobilization of Laccase

Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 581
Author(s):  
Gajanan S. Ghodake ◽  
Surendra K. Shinde ◽  
Ganesh D. Saratale ◽  
Rijuta G. Saratale ◽  
Min Kim ◽  
...  
Keyword(s):  
Enzyme Immobilization ◽  
Photoelectron Spectroscopy ◽  
Cellulose Fibers ◽  
Relative Activity ◽  
Significant Activity ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Laccase Immobilization ◽  
Surface Modified

The utilization of waste-paper-biomass for extraction of important α-cellulose biopolymer, and modification of extracted α-cellulose for application in enzyme immobilization can be extremely vital for green circular bio-economy. Thus, in this study, α-cellulose fibers were super-magnetized (Fe3O4), grafted with chitosan (CTNs), and thiol (-SH) modified for laccase immobilization. The developed material was characterized by high-resolution transmission electron microscopy (HR-TEM), HR-TEM energy dispersive X-ray spectroscopy (HR-TEM-EDS), X-ray diffraction (XRD), vibrating sample magnetometer (VSM), X-ray photoelectron spectroscopy (XPS), and Fourier transform infrared spectroscopy (FT-IR) analyses. Laccase immobilized on α-Cellulose-Fe3O4-CTNs (α-Cellulose-Fe3O4-CTNs-Laccase) gave significant activity recovery (99.16%) and laccase loading potential (169.36 mg/g). The α-Cellulose-Fe3O4-CTNs-Laccase displayed excellent stabilities for temperature, pH, and storage time. The α-Cellulose-Fe3O4-CTNs-Laccase applied in repeated cycles shown remarkable consistency of activity retention for 10 cycles. After the 10th cycle, α-Cellulose-Fe3O4-CTNs possessed 80.65% relative activity. Furthermore, α-Cellulose-Fe3O4-CTNs-Laccase shown excellent degradation of pharmaceutical contaminant sulfamethoxazole (SMX). The SMX degradation by α-Cellulose-Fe3O4-CTNs-Laccase was found optimum at incubation time (20 h), pH (3), temperatures (30 °C), and shaking conditions (200 rpm). Finally, α-Cellulose-Fe3O4-CTNs-Laccase gave repeated degradation of SMX. Thus, this study presents a novel, waste-derived, highly capable, and super-magnetic nanocomposite for enzyme immobilization applications.

Highly active carbon nanotube–promoted Rh-Mn-Li/SiO2 catalysts for the synthesis of C2+ oxygenates from syngas

2021 ◽  
pp. 174751982098472
Author(s):  
Jun Yu ◽  
Ying Han ◽  
Guoqing Chen ◽  
Xiuzhen Xiao ◽  
Haifang Mao ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Photoelectron Spectroscopy ◽  
Co Hydrogenation ◽  
X Ray ◽  
Highly Active ◽  
Transmission Electron ◽  
Co Insertion ◽  
Temperature Programmed Surface Reaction ◽  
Temperature Programmed ◽  
Oxygenate Synthesis

The effect of carbon nanotubes on the catalytic properties of Rh-Mn-Li/SiO2 catalysts was investigated for CO hydrogenation. The catalysts were comprehensively characterized by means of X-ray power diffraction, N2 sorption, transmission electron microscope, H2–temperature-programmed reduction, CO–temperature-programmed desorption, temperature-programmed surface reaction, and X-ray photoelectron spectroscopy. The results showed that an appropriate amount of carbon nanotubes can be attached to the surface of the SiO2 sphere and can improve the Rh dispersion. Moderate Rh-Mn interaction can be obtained by doping with the appropriate amount of carbon nanotubes, which promotes the formation of strongly adsorbed CO and facilitates the progress of CO insertion, resulting in the increase in the selectivity of C2+ oxygenate synthesis.

Sign in / Sign up

Export Citation Format

Share Document