scholarly journals Particle Number Emissions of a Euro 6d-Temp Gasoline Vehicle under Extreme Temperatures and Driving Conditions

Catalysts ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 607
Author(s):  
Barouch Giechaskiel ◽  
Victor Valverde ◽  
Anastasios Kontses ◽  
Anastasios Melas ◽  
Giorgio Martini ◽  
...  
Keyword(s):  
Particle Number ◽  
Direct Injection ◽  
Urban Traffic ◽  
Gasoline Direct Injection ◽  
Ambient Temperatures ◽  
The Road ◽  
Wide Range ◽  
European Regulatory ◽  
Driving Conditions ◽  
On The Road

With the introduction of gasoline particulate filters (GPFs), the particle number (PN) emissions of gasoline direct-injection (GDI) vehicles are below the European regulatory limit of 6 × 1011 p/km under certification conditions. Nevertheless, concerns have been raised regarding emission levels at the boundaries of ambient and driving conditions of the real-driving emissions (RDE) regulation. A Euro 6d-Temp GDI vehicle with a GPF was tested on the road and in the laboratory with cycles simulating congested urban traffic, dynamic driving, and towing a trailer uphill at 85% of maximum payload. The ambient temperatures covered a range from −30 to 50 °C. The solid PN emissions were 10 times lower than the PN limit under most conditions and temperatures. Only dynamic driving that regenerated the filter passively, and for the next cycle resulted in relatively high emissions although they were still below the limit. The results of this study confirmed the effectiveness of GPFs in controlling PN emissions under a wide range of conditions.

scholarly journals Impacts of Extreme Ambient Temperatures and Road Gradient on Energy Consumption and CO2 Emissions of a Euro 6d-Temp Gasoline Vehicle

Energies ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 6195
Author(s):  
Barouch Giechaskiel ◽  
Dimitrios Komnos ◽  
Georgios Fontaras
Keyword(s):  
Co2 Emissions ◽  
Energy Demand ◽  
Direct Injection ◽  
Urban Traffic ◽  
Gasoline Direct Injection ◽  
Particulate Filter ◽  
Ambient Temperatures ◽  
Vehicle Simulation ◽  
Wide Range ◽  
On The Road

The EU aims to substantially reduce its greenhouse gas emissions in the following decades and achieve climate neutrality by 2050. Better CO2 estimates, particularly in urban conditions, are necessary for assessing the effectiveness of various regional policy strategies. In this study, we measured the CO2 emissions of a Euro 6d-temp gasoline direct injection (GDI) vehicle with a three-way catalyst (TWC) and a gasoline particulate filter (GPF) at ambient temperatures from −30 °C up to 50 °C with the air-conditioning on. The tests took place both on the road and in the laboratory, over cycles simulating congested urban traffic, dynamic driving, and uphill driving towing a trailer at 85% of the maximum payloads of both the car and the trailer. The CO2 values varied over a wide range depending on the temperature and driving conditions. Vehicle simulation was used to quantify the effect of ambient temperature, vehicle weight and road grade on the CO2 emissions. The results showed that vehicle energy demand was significantly increased under the test conditions. In urban trips, compared to the baseline at 23 °C, the CO2 emissions were 9–20% higher at −10 °C, 30–44% higher at −30 °C, and 37–43% higher at 50 °C. Uphill driving with a trailer had 2–3 times higher CO2 emissions. In motorway trips at 50 °C, CO2 emissions increased by 13–19%. The results of this study can help in better quantification of CO2 and fuel consumption under extreme conditions. Additional analysis on the occurrence of such conditions in real-world operation is advisable.

scholarly journals Effect of Extreme Temperatures and Driving Conditions on Gaseous Pollutants of a Euro 6d-Temp Gasoline Vehicle

Atmosphere ◽  
2021 ◽  
Vol 12 (8) ◽  
pp. 1011
Author(s):  
Barouch Giechaskiel ◽  
Victor Valverde ◽  
Anastasios Kontses ◽  
Ricardo Suarez-Bertoa ◽  
Tommaso Selleri ◽  
...  
Keyword(s):  
Heavy Traffic ◽  
Direct Injection ◽  
Urban Environments ◽  
Gasoline Direct Injection ◽  
Particulate Filter ◽  
Gaseous Emissions ◽  
Ambient Temperatures ◽  
Driving Conditions ◽  
On The Road ◽  
Cold Starts

Gaseous emissions of modern Euro 6d vehicles, when tested within real driving emissions (RDE) boundaries, are, in most cases, at low levels. There are concerns, though, about their emission performance when tested at or above the boundaries of ambient and driving conditions requirements of RDE regulations. In this study, a Euro 6d-Temp gasoline direct injection (GDI) vehicle with three-way catalyst and gasoline particulate filter was tested on the road and in a laboratory at temperatures ranging between −30 °C and 50 °C, with cycles simulating urban congested traffic, uphill driving while towing a trailer at 85% of the vehicle’s maximum payload, and dynamic driving. The vehicle respected the Euro 6 emission limits, even though they were not applicable to the specific cycles, which were outside of the RDE environmental and trip boundary conditions. Most of the emissions were produced during cold starts and at low ambient temperatures. Heavy traffic, dynamic driving, and high payload were found to increase emissions depending on the pollutant. Even though this car was one of the lowest emitting cars found in the literature, the proposed future Euro 7 limits will require a further decrease in cold start emissions in order to ensure low emission levels under most ambient and driving conditions, particularly in urban environments. Nevertheless, motorway emissions will also have to be controlled well.

scholarly journals Laboratory and On-Road Evaluation of a GPF-Equipped Gasoline Vehicle

Catalysts ◽  
2019 ◽  
Vol 9 (8) ◽  
pp. 678 ◽  
Author(s):  
Ricardo Suarez-Bertoa ◽  
Tero Lähde ◽  
Jelica Pavlovic ◽  
Victor Valverde ◽  
Michael Clairotte ◽  
...  
Keyword(s):  
Laboratory Test ◽  
Mass Production ◽  
Particle Number ◽  
Direct Injection ◽  
Gasoline Direct Injection ◽  
Nox Emissions ◽  
Ambient Temperatures ◽  
Particulate Filters ◽  
Gdi Engines ◽  
Total Hydrocarbons

The introduction of a solid particle number limit for vehicles with gasoline direct injection (GDI) engines resulted in a lot of research and improvements in this field in the last decade. The requirement to also fulfil the limit in the recently introduced real-driving emissions (RDE) regulation led to the introduction of gasoline particulate filters (GPFs) in European vehicle models. As the pre-standardisation research was based on engines, retrofitted vehicles and prototype vehicles, there is a need to better characterise the actual emissions of GPF-equipped GDI vehicles. In the present study we investigate one of the first mass production vehicles with GPF available in the European market. Regulated and non-regulated pollutants were measured over different test cycles and ambient temperatures (23 °C and −7 °C) in the laboratory and different on-road routes driven normally or dynamically and up to 1100 m altitude. The results showed that the vehicle respected all applicable limits. However, under certain conditions high emissions of some pollutants were measured (total hydrocarbons emissions at −7 °C, high CO during dynamic RDE tests and high NOx emissions in one dynamic RDE test). The particle number emissions, even including those below 23 nm, were lower than 6 × 1010 particles/km under all laboratory test cycles and on-road routes, which are <10% of the current laboratory limit (6 × 1011 particles/km).

scholarly journals Particle Number Emissions of Gasoline, Compressed Natural Gas (CNG) and Liquefied Petroleum Gas (LPG) Fueled Vehicles at Different Ambient Temperatures

Atmosphere ◽  
2021 ◽  
Vol 12 (7) ◽  
pp. 893
Author(s):  
Tero Lähde ◽  
Barouch Giechaskiel
Keyword(s):  
Natural Gas ◽  
Ambient Temperature ◽  
Solid Particle ◽  
Fossil Fuels ◽  
Particle Number ◽  
Direct Injection ◽  
Gasoline Direct Injection ◽  
Liquefied Petroleum Gas ◽  
Compressed Natural Gas ◽  
Ambient Temperatures

Compressed natural gas (CNG) and liquefied petroleum gas (LPG) are included in the group of promoted transport fuel alternatives for traditional fossil fuels in Europe. Both CNG and LPG fueled vehicles are believed to have low particle number and mass emissions. Here, we studied the solid particle number (SPN) emissions >4 nm, >10 nm and >23 nm of bi-fuel vehicles applying CNG, LPG and gasoline fuels in laboratory at 23 °C and sub-zero (−7 °C) ambient temperature conditions. The SPN23 emissions in CNG or LPG operation modality at 23 °C were below the regulated SPN23 limit of diesel and gasoline direct injection vehicles 1/km. Nevertheless, the limit was exceeded at sub-zero temperatures, when sub-23 nm particles were included, or when gasoline was used as a fuel. The key message of this study is that gas-fueled vehicles produced particles mainly <23 nm and the current methodology might not be appropriate. However, only in a few cases absolute SPN >10 nm emission levels exceeded 6 ×1011 1/km when >23 nm levels were below 6 ×1011 1/km. Setting a limit of 1 ×1011 1/km for >10 nm particles would also limit most of the >4 nm SPN levels below 6 ×1011 1/km.

scholarly journals Cycling Pathways

2021 ◽  
Author(s):  
Henk-Jan Dekker
Keyword(s):  
Climate Change ◽  
The Netherlands ◽  
Political Struggle ◽  
The Road ◽  
Wide Range ◽  
The World ◽  
Road Space ◽  
History Of ◽  
On The Road

In an effort to fight climate change, many cities try to boost their cycling levels. They often look towards the Dutch for guidance. However, historians have only begun to uncover how and why the Netherlands became the premier cycling country of the world. Why were Dutch cyclists so successful in their fight for a place on the road? Cycling Pathways: The Politics and Governance of Dutch Cycling Infrastructure, 1920-2020 explores the long political struggle that culminated in today’s high cycling levels. Delving into the archives, it uncovers the important role of social movements and shows in detail how these interacted with national, provincial, and urban engineers and policymakers to govern the distribution of road space and construction of cycling infrastructure. It discusses a wide range of topics, ranging from activists to engineering committees, from urban commuters to recreational cyclists and from the early 1900s to today in order to uncover the long and all-but-forgotten history of Dutch cycling governance.

scholarly journals Comparison of Solid Particle Number Emission of Gasoline Direct Injection Vehicles between CVS and Tailpipe Samplings

2021 ◽  
Vol 12 (4) ◽  
pp. 142-149
Author(s):  
Kazuki Nakamura ◽  
Izumi Fukano ◽  
Seiichi Hosogai ◽  
Christos Dardiotis ◽  
Christoph Kandlhofer
Keyword(s):  
Solid Particle ◽  
Particle Number ◽  
Direct Injection ◽  
Gasoline Direct Injection

A Laboratory Method to Comprehensively Evaluate Abrasion, Traction and Rolling Resistance of Tire Tread Compounds

2007 ◽  
Vol 80 (4) ◽  
pp. 580-607 ◽  
Author(s):  
M. Heinz ◽  
K. A. Grosch
Keyword(s):  
Friction Coefficient ◽  
Laboratory Test ◽  
Rolling Resistance ◽  
Limited Range ◽  
Slip Angle ◽  
Testing Conditions ◽  
Side Force ◽  
The Road ◽  
Wide Range ◽  
On The Road

Abstract A laboratory test method has been developed which allows the evaluation of diverse properties of tire tread compounds on the same sample. The laboratory test instrument consists of a rotating abrasive disk against which a rubber sample wheel runs under a given load, slip angle and speed. All three force components acting on the wheel during the tests are recorded. By changing the variable values over a wide range practically all severities encountered in tire wear are covered. The well-known fact that compound ratings depend on the road testing conditions is verified. Most compounds are only significantly distinguishable against a control over a limited range of testing conditions. Using a road test simulation computer program based on the laboratory data shows that not only ratings correspond to practical experience but also calculated absolute tire life times do. Tests on surfaces of different coarseness and sharpness indicate that sharp coarse surfaces give the best results with road tests, which of necessity are mostly carried out on public roads of differing constitution. The abrasive surface can be wetted with water at different temperatures and hence either the friction force at a locked wheel or the side force at a slipping wheel can be measured over a wide range of temperatures and speeds. At small slip angles the side force is dominated by dynamic cornering stiffness of the compound, at large slip angles by the friction coefficient. In this case, too, good correlations to road experience exist over a limited range of testing conditions. Low water temperatures and low slip speed settings in the laboratory produce side force ratings, which correlate closely with ABS braking on the road High and higher slip speeds give ratings in close agreement with locked wheel braking on the road. A heatable/coolable disk enables traction measurements on ice and newly abrasion measurements on surfaces at elevated surface temperature. Ice surface temperatures between −5 °C and −25 °C are possible. Friction measurements show that the difference in compound rating between summer and winter compounds is maintained over the whole temperature range. New investigations show not only a differentiation between different winter tire treads qualities but also an excellent correlation between tire and laboratory results. As a new topic side force measurements on dry surfaces highlight the correlation to dry handling of tires. The tire tread compound contributes to this performance through its shear stiffness and its friction coefficient. The shear stiffness contributes to the response of the tire in directional changes. The friction coefficient determines the maximum force, which can be transmitted. A simple operation possibility for evaluation of determined side forces is demonstrated. In addition to antecedent investigations the rolling resistance of the rubber wheel can be measured over a range of loads and speeds with the slip angle set at zero. Again for these new results good correlations are achieved with practical experience. In particular, the dependence of the rolling resistance on the velocity and loads are pointed out. Ultimately a good correlation between tire test and laboratory test results was demonstrated.

scholarly journals Investigation on Blending Effects of Gasoline Fuel with N-Butanol, DMF, and Ethanol on the Fuel Consumption and Harmful Emissions in a GDI Vehicle

Energies ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1845 ◽  
Author(s):  
Haifeng Liu ◽  
Xichang Wang ◽  
Diping Zhang ◽  
Fang Dong ◽  
Xinlu Liu ◽  
...  
Keyword(s):  
Steady State ◽  
Fuel Consumption ◽  
Large Fraction ◽  
Direct Injection ◽  
Transient State ◽  
Gasoline Direct Injection ◽  
Nox Emissions ◽  
Fuel Blends ◽  
Wide Range ◽  
Oxygenated Fuel

The effects of three kinds of oxygenated fuel blends—i.e., ethanol-gasoline, n-butanol-gasoline, and 2,5-dimethylfuran (DMF)-gasoline-on fuel consumption, emissions, and acceleration performance were investigated in a passenger car with a chassis dynamometer. The engine mounted in the vehicle was a four-cylinder, four-stroke, turbocharging gasoline direct injection (GDI) engine with a displacement of 1.395 L. The test fuels include ethanol-gasoline, n-butanol-gasoline, and DMF-gasoline with four blending ratios of 20%, 50%, 75%, and 100%, and pure gasoline was also tested for comparison. The original contribution of this article is to systemically study the steady-state, transient-state, cold-start, and acceleration performance of the tested fuels under a wide range of blending ratios, especially at high blending ratios. It provides new insight and knowledge of the emission alleviation technique in terms of tailoring the biofuels in GDI turbocharged engines. The results of our works showed that operation with ethanol–gasoline, n-butanol–gasoline, and DMF–gasoline at high blending ratios could be realized in the GDI vehicle without any modification to its engine and the control system at the steady state. At steady-state operation, as compared with pure gasoline, the results indicated that blending n-butanol could reduce CO2, CO, total hydrocarbon (THC), and NOX emissions, which were also decreased by employing a higher blending ratio of n-butanol. However, a high fraction of n-butanol increased the volumetric fuel consumption, and so did the DMF–gasoline and ethanol–gasoline blends. A large fraction of DMF reduced THC emissions, but increased CO2 and NOX emissions. Blending n-butanol can improve the equivalent fuel consumption. Moreover, the particle number (PN) emissions were significantly decreased when using the high blending ratios of the three kinds of oxygenated fuels. According to the results of the New European Drive Cycle (NEDC) cycle, blending 20% of n-butanol with gasoline decreased CO2 emissions by 5.7% compared with pure gasoline and simultaneously reduced CO, THC, NOX emissions, while blending ethanol only reduced NOX emissions. PN and particulate matter (PM) emissions decreased significantly in all stages of the NEDC cycle with the oxygenated fuel blends; the highest reduction ratio in PN was 72.87% upon blending 20% ethanol at the NEDC cycle. The high proportion of n-butanol and DMF improved the acceleration performance of the vehicle.

Sign in / Sign up

Export Citation Format

Share Document