scholarly journals Rhodium Nanoparticles Incorporated Mesoporous Silica as an Active Catalyst for Cyclohexene Hydrogenation under Ambient Conditions

Catalysts ◽  
2020 ◽  
Vol 10 (8) ◽  
pp. 925
Author(s):  
Mohamed S. Hamdy ◽  
Abdullah M. Alhanash ◽  
Mhamed Benaissa ◽  
Ali Alsalme ◽  
Fahad A. Alharthi ◽  
...  
Keyword(s):  
Reaction Temperature ◽  
Sol Gel ◽  
Three Dimensional ◽  
Silica Matrix ◽  
Hydrogen Gas ◽  
Ambient Conditions ◽  
Consecutive Reaction ◽  
Rhodium Nanoparticles ◽  
Optimization Parameters ◽  
Average Size

Rhodium (Rh) nanoparticles were embedded in the mesopores of TUD-1 siliceous material and denoted as Rh-TUD-1. Five samples of Rh-TUD-1 were prepared with different loadings of Rh that ranged from 0.1 to 2 wt% using the sol-gel technique. The prepared samples were characterized by means of several chemical and physical techniques. The obtained characterization results show the formation of highly distributed Rh0 nanoparticles with an average size ranging from 3 to 5 nm throughout the three-dimensional silica matrix of TUD-1. The catalytic activity of the prepared catalysts was evaluated in the solvent-free hydrogenation of cyclohexene to cyclohexane at room temperature using 1atm of hydrogen gas. The obtained catalytic results confirm the high activity of Rh-TUD-1, in which a turn over frequency (TOF) ranging from 4.94 to 0.54 s−1 was obtained. Moreover, the change in reaction temperature during the reaction was monitored, and it showed an obvious increase in the reaction temperature as an indication of the spontaneous and exothermic nature of the reactions. Other optimization parameters, such as the substrate/catalyst ratio, and performing the reaction under non-ambient conditions (temperature = 60 °C and hydrogen pressure = 5 atm) were also investigated. Rh-TUD-1 exhibited a high stability in a consecutive reaction of five runs under either ambient or non-ambient conditions.

Sol-Gel and RF Sputtering Thin Film Coatings for Fiber Optic Sensor Applications

1991 ◽  
Vol 244 ◽  
Author(s):  
M. R. Shahriari ◽  
J. Y. Ding ◽  
C. M. Wang ◽  
C. H. Lin ◽  
G. H. Sigel
Keyword(s):  
Thin Film ◽  
Optical Waveguides ◽  
Fiber Optic ◽  
Sol Gel ◽  
Rf Sputtering ◽  
Silica Matrix ◽  
Hydrogen Gas ◽  
Fiber Optic Sensor ◽  
Sensor Applications ◽  
Optic Sensor

ABSTRACTThin film coating techniques appear to have many advantages over other techniques for immobilization and incorporation of chemical indicators to optical waveguides in developing dye based fiber optic chemical sensors. We have fabricated thin films of composites by using sol-gel and RF sputtering techniques. Different organic and inorganic indicators were immobilized in these films and incorporated into optical waveguides for sensor applications. A fiber optic pH sensor has been developed by introducing pH indicators into a silica matrix and coated as a thin film onto a porous glass fiber by a sol-gel technique. Also, a hydrogen gas fiber optic sensor has been developed by using a RF sputtered WO3/Pd coated porous optical fiber.

scholarly journals Synthesis of SiO2-TiO2:Yb3+ glass-ceramics and characterization of structure and optical properties

2017 ◽  
Vol 1 (T1) ◽  
pp. 114-121
Author(s):  
Thanh Tat Huynh ◽  
Van Thi Thanh Tran
Keyword(s):  
Sol Gel ◽  
Glass Ceramics ◽  
Xrd Analysis ◽  
Silica Matrix ◽  
Photoluminescence Intensity ◽  
Raman Spectroscopic ◽  
Characteristic Emission ◽  
Ft Ir ◽  
Average Size ◽  
20 Nm

In this work, the monoliths of 85 % SiO2-15 % TiO2 doped Yb3+ ions at different contents have been prepared by sol-gel method. The measurement of FT-IR, Raman spectroscopic and XRD analysis show the formation of anatase TiO2 nanocrystals with average size about 15–20 nm in silica matrix. Moreover, the pyrochlore crystals of Yb2Ti2O7 begin to form in the samples when content of Yb3+ reaches to 1 mol %. TiO2 Yb3+ 2F7/2 2F5/2 truyền năng lƣợng kích thích UV EV EC mức khuyết tật 974 nm The energy transferred from TiO2 crystals to Yb3+ ions is proven by the characteristic emission spectrum of Yb3+ at the wavelength of 980 nm when the samples are excited by the wavelength of 300 nm. The photoluminescence intensity is highest at 0.1% mol of Yb3+ and gradually decreases with doping content

Synthesis and Characterization of Sol–Gel Prepared Silver Nanoparticles

2014 ◽  
Vol 13 (01) ◽  
pp. 1450004 ◽  
Author(s):  
Dharamvir Singh Ahlawat ◽  
Rekha Kumari ◽  
Rachna ◽  
Indu Yadav
Keyword(s):  
Silver Nanoparticles ◽  
Absorption Spectra ◽  
Annealing Temperature ◽  
Sol Gel ◽  
Xrd Analysis ◽  
Silica Matrix ◽  
Silver Clusters ◽  
Different Temperatures ◽  
Uv Visible ◽  
Average Size

Silver nanoparticles (SNPs) have been successfully prepared using sol–gel method by annealing the sample at 550°C for 30 min. The SNPs were not confirmed by X-ray diffraction (XRD) analysis when the annealing temperature was considered at 450°C. They were also not confirmed without calcination of the sample. The physical mechanism of silver clusters formation in the densified silica matrix with respect to thermal treatment has been understood. The presence of silver metal in the silica matrix was confirmed by XRD analysis and TEM image of the samples. The average size of nanoparticles dispersed in silica matrix was determined as 10.2 nm by the XRD technique. The synthesized nanocomposites were also characterized by UV-Visible spectroscopy with a peak in the absorption spectra at around 375 nm. The distribution of particle size has been reported here in the range from 8 nm to 25 nm by TEM observations of the sample prepared at 550°C. The spherically smaller size (≈10 nm) SNPs have reported the surface plasmons resonance (SPR) peak less than or near to 400 nm due to blue-shifting and effect of local refractive index. Without annealing the silica samples the absorption spectra does not show any peak around 375 nm. The FTIR spectroscopy of the three types of samples prepared at different temperatures (room temperature, 450°C and 550°C) has also been reported. This spectra have provided the identification of different chemical groups in the prepared samples. It has been predicted that the size of SNPs by XRD, UV-Visible and TEM results have agreed well with each other. It may be concluded that formation of SNPs is a function of annealing temperature.

Hybrid Micro-Optical Sensors via Sol-Gel Soft Lithography

2000 ◽  
Vol 628 ◽  
Author(s):  
Mark A. Clarner ◽  
Michael J. Lochhead
Keyword(s):  
Optical Sensors ◽  
Soft Lithography ◽  
Sol Gel ◽  
Silica Gels ◽  
Ph Sensing ◽  
Ambient Conditions ◽  
Sensor Applications ◽  
Patterned Structures ◽  
Biological Functionality ◽  
Indicator Dyes

ABSTRACTOrganically modified silica gels and dye-doped silica gels have been patterned into micrometer-scale structures on a substrate using micro molding in capillaries (MIMIC). This approach is from a class of elastomeric stamping and molding techniques collectively known as soft lithography. Soft lithography and sol-gel processing share attractive features in that they are relatively benign processes performed at ambient conditions, which makes both techniques compatible with a wide variety of organic molecules, molecular assemblies, and biomolecules. The combination of sol-gel and soft lithography, therefore, holds enormous promise as a tool for microfabrication of materials with optical, chemical, or biological functionality that are not readily patterned with conventional methods. This paper describes our investigation of micro-patterned organic-inorganic hybrid materials containing indicator dyes for microfluidic sensor applications. Reversible colorimetric pH sensing via entrapped reagents is demonstrated in a prototype microfluidic sensor element. Patterned structures range from one to tens of micrometers in cross-section and are up to centimeters in length. Fundamental chemical processing issues associated with mold filling, cracking and sensor stability are discussed.

Macrocellular Titanosilicate Monoliths as Highly Efficient Structured Olefin Epoxidation Catalysts

2019 ◽  
Author(s):  
Valentin Smeets ◽  
Ludivine van den Biggelaar ◽  
Tarek Barakat ◽  
Eric M. Gaigneaux ◽  
Damien Debecker
Keyword(s):  
Sol Gel ◽  
Silica Matrix ◽  
Flow Mode ◽  
Tetrahedral Coordination ◽  
Excellent Performance ◽  
One Pot ◽  
Templating Method ◽  
Porous Texture ◽  
Internal Phase ◽  
Epoxidation Of Cyclohexene

Self-standing macrocellular titanosilicate monolith foams are obtained using a one-pot sol-gel route and show excellent performance in the epoxidation of cyclohexene. Thanks to the High Internal Phase Emulsion (HIPE) templating method, the materials feature a high void fraction, a hierarchically porous texture and good mechanical strength. Highly dispersed Ti species can be incorporated in tetrahedral coordination the silica matrix. These characteristics allow the obtained ‘SiTi(HIPE)’ materials to reach high catalytic turnover in the epoxidation of cyclohexene. The monoliths can advantageously be used to run the reaction in continuous flow mode.<br>

scholarly journals Construction of the Cellulose Nanofibers (CNFs) Aerogel Loading TiO2 NPs and Its Application in Disposal of Organic Pollutants

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1841
Author(s):  
Kang Li ◽  
Xuejie Zhang ◽  
Yan Qin ◽  
Ying Li
Keyword(s):  
High Efficiency ◽  
Sol Gel ◽  
Cellulose Nanofibers ◽  
Three Dimensional ◽  
Good Mechanical Property ◽  
Polar Groups ◽  
Dimensional Network ◽  
Natural Polysaccharide ◽  
Valuable Method ◽  
Adsorption Capability

Aerogels have been widely used in the adsorption of pollutants because of their large specific surface area. As an environmentally friendly natural polysaccharide, cellulose is a good candidate for the preparation of aerogels due to its wide sources and abundant polar groups. In this paper, an approach to construct cellulose nanofibers aerogels with both the good mechanical property and the high pollutants adsorption capability through chemical crosslinking was explored. On this basis, TiO2 nanoparticles were loaded on the aerogel through the sol-gel method followed by the hydrothermal method, thereby the enriched pollutants in the aerogel could be degraded synchronously. The chemical cross-linker not only helps build the three-dimensional network structure of aerogels, but also provides loading sites for TiO2. The degradation efficiency of pollutants by the TiO2@CNF Aerogel can reach more than 90% after 4 h, and the efficiency is still more than 70% after five cycles. The prepared TiO2@CNF Aerogels have high potential in the field of environmental management, because of the high efficiency of treating organic pollutes and the sustainability of the materials. The work also provides a choice for the functional utilization of cellulose, offering a valuable method to utilize the large amount of cellulose in nature.

scholarly journals Construction of a Three-Dimensional BaTiO3 Network for Enhanced Permittivity and Energy Storage of PVDF Composites

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3585
Author(s):  
Xueqing Bi ◽  
Lujia Yang ◽  
Zhen Wang ◽  
Yanhu Zhan ◽  
Shuangshuang Wang ◽  
...  
Keyword(s):  
Energy Storage ◽  
Polyvinylidene Fluoride ◽  
Dielectric Breakdown ◽  
Breakdown Strength ◽  
Sol Gel ◽  
Three Dimensional ◽  
Low Dielectric ◽  
Energy Storage Properties ◽  
Discharge Energy Density ◽  
Pure Pvdf

Three-dimensional BaTiO3 (3D BT)/polyvinylidene fluoride (PVDF) composite dielectrics were fabricated by inversely introducing PVDF solution into a continuous 3D BT network, which was simply constructed via the sol-gel method using a cleanroom wiper as a template. The effect of the 3D BT microstructure and content on the dielectric and energy storage properties of the composites were explored. The results showed that 3D BT with a well-connected continuous network and moderate grain sizes could be easily obtained by calcining a barium source containing a wiper template at 1100 °C for 3 h. The as-fabricated 3D BT/PVDF composites with 21.1 wt% content of 3D BT (3DBT–2) exhibited the best comprehensive dielectric and energy storage performances. An enhanced dielectric constant of 25.3 at 100 Hz, which was 2.8 times higher than that of pure PVDF and 1.4 times superior to the conventional nano–BT/PVDF 25 wt% system, was achieved in addition with a low dielectric loss of 0.057 and a moderate dielectric breakdown strength of 73.8 kV·mm−1. In addition, the composite of 3DBT–2 exhibited the highest discharge energy density of 1.6 × 10−3 J·cm−3 under 3 kV·mm−1, which was nearly 4.5 times higher than that of neat PVDF.

scholarly journals Upconversion Luminescence of Silica–Calcia Nanoparticles Co-doped with Tm3+ and Yb3+ Ions

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 937
Author(s):  
Katarzyna Halubek-Gluchowska ◽  
Damian Szymański ◽  
Thi Ngoc Lam Tran ◽  
Maurizio Ferrari ◽  
Anna Lukowiak
Keyword(s):  
Energy Transfer ◽  
Near Infrared ◽  
Upconversion Luminescence ◽  
Sol Gel ◽  
Emission Spectra ◽  
Transmission Electron ◽  
Characteristic Emission ◽  
Diffraction Patterns ◽  
Size Of Particles ◽  
Average Size

Looking for upconverting biocompatible nanoparticles, we have prepared by the sol–gel method, silica–calcia glass nanopowders doped with different concentration of Tm3+ and Yb3+ ions (Tm3+ from 0.15 mol% up to 0.5 mol% and Yb3+ from 1 mol% up to 4 mol%) and characterized their structure, morphology, and optical properties. X-ray diffraction patterns indicated an amorphous phase of the silica-based glass with partial crystallization of samples with a higher content of lanthanides ions. Transmission electron microscopy images showed that the average size of particles decreased with increasing lanthanides content. The upconversion (UC) emission spectra and fluorescence lifetimes were registered under near infrared excitation (980 nm) at room temperature to study the energy transfer between Yb3+ and Tm3+ at various active ions concentrations. Characteristic emission bands of Tm3+ ions in the range of 350 nm to 850 nm were observed. To understand the mechanism of Yb3+–Tm3+ UC energy transfer in the SiO2–CaO powders, the kinetics of luminescence decays were studied.

scholarly journals Transient Three-Dimensional Flow Field Measurements by Means of 3D µPTV in Drying Poly(Vinyl Acetate)-Methanol Thin Films Subject to Short-Scale Marangoni Instabilities

Polymers ◽  
2021 ◽  
Vol 13 (8) ◽  
pp. 1223
Author(s):  
Max Tönsmann ◽  
Philip Scharfer ◽  
Wilhelm Schabel
Keyword(s):  
Flow Field ◽  
Vinyl Acetate ◽  
Three Dimensional ◽  
Field Measurements ◽  
Initial Assessment ◽  
Ambient Conditions ◽  
Three Dimensional Flow ◽  
Dimensional Flow ◽  
Short Scale ◽  
Dry Film

Convective Marangoni instabilities in drying polymer films may induce surface deformations, which persist in the dry film, deteriorating product performance. While theoretic stability analyses are abundantly available, experimental data are scarce. We report transient three-dimensional flow field measurements in thin poly(vinyl acetate)-methanol films, drying under ambient conditions with several films exhibiting short-scale Marangoni convection cells. An initial assessment of the upper limit of thermal and solutal Marangoni numbers reveals that the solutal effect is likely to be the dominant cause for the observed instabilities.

scholarly journals Synthesis, Structural, Morphological and Thermal Characterization of Five Different Silica-Polyethylene Glycol-Chlorogenic Acid Hybrid Materials

Polymers ◽  
2021 ◽  
Vol 13 (10) ◽  
pp. 1586
Author(s):  
Michelina Catauro ◽  
Pavel Šiler ◽  
Jiří Másilko ◽  
Roberta Risoluti ◽  
Stefano Vecchio Ciprioti
Keyword(s):  
Polyethylene Glycol ◽  
Chlorogenic Acid ◽  
Hybrid Materials ◽  
Sol Gel ◽  
Antibacterial Properties ◽  
Silica Matrix ◽  
Sem Images ◽  
Fixed Amount ◽  
Organic Components ◽  
Free Material

The present study investigated the structure, morphology, thermal behavior, and bacterial growth analysis of novel three-component hybrid materials synthesized by the sol-gel method. The inorganic silica matrix was weakly bonded to the network of two organic components: a well-known polymer such as polyethylene glycol (PEG, average molar mass of about 4000 g/mol), and an antioxidant constituted by chlorogenic acid (CGA). In particular, a first series was made by a 50 wt% PEG-based (CGA-free) silica hybrid along with two 50 wt% PEG-based hybrids containing 10 and 20 wt% of CGA (denoted as SP50, SP50C10 and SP50C20, respectively). A second series contained a fixed amount of CGA (20 wt%) in silica-based hybrids: one was the PEG-free material (SC20) and the other two contained 12 and 50 wt% of PEG, respectively (SP12C20 and SP50C20, respectively), being the latter already included in the first series. The X-ray diffraction (XRD) patterns and scanning electron microscope (SEM) images of freshly prepared materials confirmed that all the materials were amorphous and homogeneous regardless of the content of PEG or CGA. The thermogravimetric (TG) analysis revealed a higher water content was adsorbed into the two component hybrids (SP50 and SC20) because of the availability of a larger number of H-bonds to be formed with water with respect to those of silica/PEG/CGA (SPC), where silica matrix was involved in these bonds with both organic components. Conversely, the PEG-rich materials (SP50C10 and SP50C20, both with 50 wt% of the polymer) retained a lower content of water. Decomposition of PEG and CGA occurred in almost the same temperature interval regardless of the content of each organic component. The antibacterial properties of the SiO2/PEG/CGA hybrid materials were studied in pellets using either Escherichia coli and Enterococcus faecalis, respectively. Excellent antibacterial activity was found against both bacteria regardless of the amount of polymer in the hybrids.

Sign in / Sign up

Export Citation Format

Share Document