scholarly journals Artificial Neural Network Estimation of the Effect of Varying Curing Conditions and Cement Type on Hardened Concrete Properties

Buildings ◽  
2019 ◽  
Vol 9 (1) ◽  
pp. 10 ◽  
Author(s):  
Gökhan Kaplan ◽  
Hasbi Yaprak ◽  
Selçuk Memiş ◽  
Abdoslam Alnkaa
Keyword(s):  
Compressive Strength ◽  
Portland Cement ◽  
Limestone Powder ◽  
Mineral Admixtures ◽  
Hardened Concrete ◽  
Slag Cement ◽  
Curing Conditions ◽  
Concrete Properties ◽  
Concrete Production ◽  
Artificial Neural

The use of mineral admixtures and industrial waste as a replacement for Portland cement is recognized widely for its energy efficiency along with reduced CO2 emissions. The use of materials such as fly ash, blast-furnace slag or limestone powder in concrete production makes this process a sustainable one. This study explored a number of hardened concrete properties, such as compressive strength, ultrasonic pulse velocity, dynamic elasticity modulus, water absorption and depth of penetration under varying curing conditions having produced concrete samples using Portland cement (PC), slag cement (SC) and limestone cement (LC). The samples were produced at 0.63 and 0.70 w/c (water/cement) ratios. Hardened concrete samples were then cured under three conditions, namely standard (W), open air (A) and sealed plastic bag (B). Although it was found that the early-age strength of slag cement was lower, it was improved significantly on 90th day. In terms of the effect of curing conditions on compressive strength, cure W offered the highest compressive strength, as expected, while cure A offered slightly lower compressive strength levels. An increase in the w/c ratio was found to have a negative impact on pozzolanic reactions, which resulted in poor hardened concrete properties. Furthermore, carbonation effect was found to have positive effects on some of the concrete properties, and it was observed to have improved the depth of water penetration. Moreover, it was possible to estimate the compressive strength with high precision using artificial neural networks (ANN). The values of the slopes of the regression lines for training, validating and testing datasets were 0.9881, 0.9885 and 0.9776, respectively. This indicates the high accuracy of the developed model as well as a good correlation between the predicted compressive strength values and the experimental (measured) ones.

scholarly journals Effect of internal curing on performance of self-compacting concrete by using sustainable materials

2018 ◽  
Vol 162 ◽  
pp. 02017
Author(s):  
Nada Aljalawi ◽  
Amar Yahia AL-Awadi
Keyword(s):  
Compressive Strength ◽  
Lightweight Aggregate ◽  
Internal Curing ◽  
Modulus Of Rupture ◽  
Limestone Powder ◽  
Partial Replacement ◽  
Hardened Concrete ◽  
Self Compacting Concrete ◽  
Curing Conditions ◽  
Compressive Strength Test

This paper is devoted to investigate the effect of internal curing technique on the properties of self-compacting concrete. In this study, self-compacting concrete is produced by using limestone powder as partial replacement by weight of cement with percentage of (5%), sand is partially replaced by volume with saturated fine lightweight aggregate which is thermostone aggregate as internal curing material in three percentages of (5%, 10%, 15%) for self-compacting concrete, and the use of two external curing conditions which are water and air. The experimental work was divided into three parts: in the first part, the workability tests of fresh self-compacting concrete were conducted. The second part included conducting compressive strength test and modulus of rupture test at ages of (7, 28 and 90) days. The third part included doing the shrinkage test at age of (7, 14, 21, 28) days. The results show that internally cured self-compacting concrete has the best workability and the best properties of hardened concrete which include (compressive strength, modulus of rupture) of externally cured self-compacting concrete with both water and air as compared with reference concretes. Also, the hardened properties of internally cured self-compacting concrete with percentage of (5%) with thermostone aggregate is the best as compared with that of percentages (10% and 15%) in both external curing conditions. In general, the results of shrinkage test have shown reduction in shrinkage of internally cured self-compacting concrete as compared with reference concretes and this reduction increases with increase in the thermostone aggregate content-within-self-compacting-concrete.

scholarly journals Proportioning Self Compacting Concrete in Hot Weather Utilizing Limestone Powder

2019 ◽  
pp. 6-10
Author(s):  
Yousif Hummaida Ahmed
Keyword(s):  
Compressive Strength ◽  
Cement Content ◽  
The Self ◽  
Limestone Powder ◽  
Hardened Concrete ◽  
Self Compacting Concrete ◽  
Concrete Properties ◽  
Slump Flow ◽  
Hot Weather ◽  
Powder Content

Self-compacting concrete (SCC) is a special type of concrete able to flow and compact under its self-weight. The SCC requires high powder content (mainly of cement) up to 600kg/m3 to achieve its properties. This will be problematic if all cement content in the powder exceeded 400 kg/m3used in hot weather of Sudan. This paper investigates addition of Sudanese limestone powder (LSP) to reduce cement content. The LSP dosages between 20% and 28 % (by cement weight) are used in six mixes having maximum cement content 380kg/m3. Results show that five trial mixes achieved the self-compactibility tested by slump flow, sieve segregation, V-funnel and U-box tests. Compressive strength of these mixes show that the LSP increases strength with dosage. Therefore, further investigations of hardened concrete properties are recommended for the successful mixes to be applied in real projects in the Sudan. Also, it has been found that dry batching and forced-action pan mixers are the most suitable for producing SCC with high homogeneity compared to commercial tilted-drum mixers.

Experimental Study on Various Mineral Admixtures in Fibre Reinforced Concrete

2019 ◽  
pp. 309-317
Author(s):  
Kavitha E ◽  
Karthik S ◽  
Eithya B ◽  
Seenirajan M
Keyword(s):  
Fly Ash ◽  
Rice Husk ◽  
Power Plants ◽  
Rice Husk Ash ◽  
Thermal Power ◽  
Experimental Studies ◽  
Mineral Admixtures ◽  
Hardened Concrete ◽  
Polypropylene Fibres ◽  
Concrete Production

The quantity of fly ash produced from thermal power plants in India is approximately 80 million tons each year, and its percentage utilization is less than 10%. An attempt has been made to utilize these cheaper materials in concrete production. This thesis aims at investigating the characteristics of fresh concrete and various strengths of hardened concrete made with various mineral admixtures such as fly ash. GGBFS, silica fume. Rice husk ash along with polypropylene fibres in various proportions.  M20 grade concrete is considered for experimental studies with 53grade Ordinary Portland Cement blended with varying percentages of mineral admixtures. The maximum size of coarse aggregate used is 20mm.  Various mineral admixtures such as fly ash. GGBFS.Silica fume. Rice Husk Ash were added concrete in various percentages by partially replacing cement and the optimum percentage of the mineral admixtures will be found.  Based on the obtained values, the admixture with maximum mechanical strength is determined and to this polypropylene fibre is added by varying 0 to 0.5 % by weight of cement to the mix.  The test results obtained were compared and discussed with conventional concrete.

scholarly journals The use of a volcanic material as filler in self-compacting concrete production for lower strength applications

2017 ◽  
Vol 67 (325) ◽  
pp. 111 ◽  
Author(s):  
D. Burgos ◽  
A. Guzmán ◽  
K. M.A. Hossain ◽  
S. Delvasto
Keyword(s):  
Compressive Strength ◽  
Portland Cement ◽  
Cementitious Material ◽  
Total Weight ◽  
Self Compacting Concrete ◽  
Lower Strength ◽  
Volcanic Material ◽  
Fine Powders ◽  
Slump Flow ◽  
Concrete Production

This study evaluates the use of large amounts of fine powders (fillers) derived from a Colombian volcanic material into the production of self-compacting concrete (SCC) for lower strength applications. The effects on SCC properties were studied with the incorporation of up to 50% of volcanic material of Tolima (MVT) as a partial substitute of the total weight of Portland cement. The workability was determined through slump flow, V-funnel, and L-box test. The compressive strength results were analyzed statistically by MINITAB. These demonstrated that 30% (by total weight of cementitious material) was the maximum allowable percentage of MVT to be used in the production of SCCs. Based on this, mechanical and permeability properties of SCC MVT 30% were evaluated at 28, 90 y 360 curing days. SCC MVT 30% exhibited compressive strength of 21 and 27 MPa after 28 and 360 days of curing, respectively.

scholarly journals Utilization of Sugarcane Bagasse Ash from Power Co-generation Boilers as a Supplementary Cementitious Material

2021 ◽  
Vol 2 (2) ◽  
Author(s):  
Safiki Ainomugisha ◽  
Bisaso Edwin ◽  
Bazairwe Annet
Keyword(s):  
Compressive Strength ◽  
Portland Cement ◽  
Sugarcane Bagasse ◽  
Low Income ◽  
Ordinary Portland Cement ◽  
Construction Material ◽  
Sustainable Construction ◽  
Partial Replacement ◽  
Hardened Concrete ◽  
Sugarcane Bagasse Ash

Concrete has been the world’s most consumed construction material, with over 10 billion tons of concrete annually. This is mainly due to its excellent mechanical and durability properties plus high mouldability. However, one of its major constituents; Ordinary Portland Cement is reported to be expensive and unaffordable by most low-income earners. Its production contributes about 5%–8% of global CO2 greenhouse emissions. This is most likely to increase exponentially with the demand of Ordinary Portland Cement estimated to rise by 200%, reaching 6000 million tons/year by 2050.  Therefore, different countries are aiming at finding alternative sustainable construction materials that are more affordable and offer greener options reducing reliance on non-renewable sources. Therefore, this study aimed at assessing the possibility of utilizing sugarcane bagasse ash from co-generation in sugar factories as supplementary material in concrete. Physical and chemical properties of this sugarcane bagasse ash were obtained plus physical and mechanical properties of fresh and hardened concrete made with partial replacement of Ordinary Portland Cement. Cost-benefit analysis of concrete was also assessed. The study was carried using 63 concrete cubes of size 150cm3 with water absorption studied as per BS 1881-122; slump test to BS 1881-102; and compressive strength and density of concrete according to BS 1881-116. The cement binder was replaced with sugarcane bagasse ash 0%, 5%, 10%, 15%, 20%, 25% and 30% by proportion of weight. Results showed the bulk density of sugarcane bagasse ash at 474.33kg/m3, the specific gravity of 1.81, and 65% of bagasse ash has a particle size of less than 0.28mm. Chemically, sugarcane bagasse ash contained SiO2, Fe2O3, and Al2O3 at 63.59%, 3.39%, and 5.66% respectively. A 10% replacement of cement gave optimum compressive strength of 26.17MPa. This 10% replacement demonstrated a cost saving of 5.65% compared with conventional concrete. 

scholarly journals Biofuel Combustion Fly Ash Influence on the Properties of Concrete

2016 ◽  
Vol 7 (5) ◽  
pp. 546-550
Author(s):  
Aurelijus Daugėla ◽  
Džigita Nagrockienė ◽  
Laurynas Zarauskas
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Portland Cement ◽  
Water Absorption ◽  
Frost Resistance ◽  
Ash Content ◽  
Mineral Admixtures ◽  
Binding Agent ◽  
Materials Used ◽  
Plasticizing Admixture

Cement as the binding agent in the production of concrete can be replaced with active mineral admixtures. Biofuel combustion fly ash is one of such admixtures. Materials used for the study: Portland cement CEM I 42.5 R, sand of 0/4 fraction, gravel of 4/16 fraction, biofuel fly ash, superplasticizer, water. Six compositions of concrete were designed by replacing 0%, 5%, 10%, 15% 20%, and 25% of cement with biofuel fly ash. The article analyses the effect of biofuel fly ash content on the properties of concrete. The tests revealed that the increase of biofuel fly ash content up to 20% increases concrete density and compressive strength after 7 and 28 days of curing and decreases water absorption, with corrected water content by using plasticizing admixture. It was found that concrete where 20% of cement is replaced by biofuel ash has higher frost resistance.

scholarly journals Retraction Note to: Prediction compressive strength of Portland cement-based geopolymers by artificial neural networks

2020 ◽  
Vol 32 (19) ◽  
pp. 15669-15669
Author(s):  
Ali Nazari ◽  
Hadi Hajiallahyari ◽  
Ali Rahimi ◽  
Hamid Khanmohammadi ◽  
Mohammad Amini
Keyword(s):  
Neural Networks ◽  
Compressive Strength ◽  
Artificial Neural Networks ◽  
Portland Cement ◽  
Artificial Neural

scholarly journals Performance Evaluation of Ordinary Portland Cement with GGBFS and Portland Slag Cement at Same GGBFS Replacement Level in Concrete

2018 ◽  
Vol 203 ◽  
pp. 06004
Author(s):  
Ramesh Babu Chokkalingam ◽  
Manikandan Rajakannu
Keyword(s):  
Portland Cement ◽  
Ordinary Portland Cement ◽  
Concrete Structures ◽  
Blended Cement ◽  
Mineral Admixtures ◽  
Slag Cement ◽  
Control Practice ◽  
Cement Manufacturing ◽  
Portland Slag Cement ◽  
Durability Of Concrete

Literature review indicates that the usage of mineral admixtures (Fly ash, Ground Granulated Blast Furnace Slag, Silica Fume and Rice Husk ash) significantly improves the durability of concrete structures. Though it is reported as best alternative materials for improving durability of concrete structures, it was not very well received in government projects in India till 1990. However, for the past two decades, the usage of mineral admixtures directly or in the form of blended cement in concrete have significantly increased. Major concern of using mineral admixtures which was persisting among majority of the Ordinary Portland Cement (OPC) users are (i) delayed setting and strength gain, affecting the rate of construction, (ii) inconsistent in quality of mineral admixtures, mostly happened in site blending (iii) no established results pertains to Indian condition. In India, mostly the usage of mineral admixtures in concrete are used as a replacement for OPC, specifically in Ready Mix Concrete and site batching plant. However, few literature have reported that usage of mineral admixtures in the form of blended cement which is made at cement manufacturing plant by either intergrinding or blending will exhibits better concrete properties due to consistent quality and better quality control practice followed. Hence, the authors have undertaken this study to investigate the performance of mineral admixtures (only GGBFS) as direct replacement materials and as blended cement in concrete. In order to understand in detail, both as replacement of OPC and in the form of PSC, was undertaken on various cement content in concrete, i.e., 300, 320, 340, 360, 380 kg/m3. Results of compressive strength at various age of curing indicates that usage of GGBFS in the form of Portland Slag Cement (PSC) shows better performance than as a replacement of OPC in concrete.

scholarly journals Study of Hydration and Microstructure of Mortar Containing Coral Sand Powder Blended with SCMs

Materials ◽  
2020 ◽  
Vol 13 (19) ◽  
pp. 4248
Author(s):  
Xingxing Li ◽  
Ying Ma ◽  
Xiaodong Shen ◽  
Ya Zhong ◽  
Yuwei Li
Keyword(s):  
Compressive Strength ◽  
Portland Cement ◽  
Silica Fume ◽  
Dilution Effect ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Limestone Powder ◽  
Chemical Effect ◽  
Granulated Blast Furnace Slag ◽  
Coral Sand

The utilization of coral waste is an economical way of using concrete in coastal and offshore constructions. Coral waste with more than 96% CaCO3 can be ground to fines and combined with supplementary cementitious materials (SCMs) such as fly ash, silica fume, granulated blast furnace slag in replacing Portland cement to promote the properties of cement concrete. The effects of coral sand powder (CSP) compared to limestone powder (LSP) blended with SCMs on hydration and microstructure of mortar were investigated. The result shows CSP has higher activity than LSP when participating in the chemical reaction. The chemical effect among CSP, SCMs, and ordinary Portland cement (OPC) results in the appearance of the third hydration peak, facilitating the production of carboaluminate. CSP-SCMs mortar has smaller interconnected pores on account of the porous character of CSP as well as the filler and chemical effect. The dilution effect of CSP leads to the reduction of compressive strength of OPC-CSP and OPC-CSP-SCMs mortars. The synergic effects of CSP with slag and silica fume facilitate the development of compressive strength and lead to a compacted isolation and transfer zone (ITZ) in mortar.

scholarly journals Ultrasonic Pulse Velocity—Compressive Strength Relationship for Portland Cement Mortars Cured at Different Conditions

Crystals ◽  
2020 ◽  
Vol 10 (2) ◽  
pp. 133 ◽  
Author(s):  
Esteban Estévez ◽  
Domingo Alfonso Martín ◽  
Cristina Argiz ◽  
Miguel Ángel Sanjuán
Keyword(s):  
Compressive Strength ◽  
Portland Cement ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Internal Quality ◽  
Curing Conditions ◽  
Linear Relationships ◽  
Cement Mortars ◽  
Strength Relationship

The purpose of this paper is to establish some correlations between the main technical parameter with regard to the cement-based materials technology, the 28-day compressive strength, and ultrasonic pulse velocity of standard mortar samples cured at three different conditions—(i) under water at 22 °C; (ii) climatic chamber at 95% RH and 22 °C; (iii) lab ambient, 50% RH, and 22 °C—and after five curing periods of 1, 2, 7, 14, and 28 days. Good correlations for each curing conditions were obtained. All the positive linear relationships showed better R2 than exponential ones. These findings may promote the use of ultrasonic pulse velocity for the estimation of the 28-day compressive strength of standard Portland cement samples within the factory internal quality control.

Sign in / Sign up

Export Citation Format

Share Document