scholarly journals Hemodynamic Investigation of the Effectiveness of a Two Overlapping Flow Diverter Configuration for Cerebral Aneurysm Treatment

2021 ◽  
Vol 8 (10) ◽  
pp. 143
Author(s):  
Yuya Uchiyama ◽  
Soichiro Fujimura ◽  
Hiroyuki Takao ◽  
Takashi Suzuki ◽  
Motoharu Hayakawa ◽  
...  
Keyword(s):  
Cfd Simulation ◽  
Cerebral Aneurysms ◽  
Flow Diverter ◽  
Cfd Simulations ◽  
Qualitative And Quantitative ◽  
Pressure Loss Coefficient ◽  
Computational Fluid Dynamics Cfd ◽  
Simulation Results ◽  
Wide Neck ◽  
Flow Diverters

Flow diverters (FDs) are widely employed as endovascular treatment devices for large or wide-neck cerebral aneurysms. Occasionally, overlapped FDs are deployed to enhance the flow diversion effect. In this study, we investigated the hemodynamics of overlapping FDs via computational fluid dynamics (CFD) simulations. We reproduced the arterial geometry of a patient who had experienced the deployment of two overlapping FDs. We utilized two stent patterns, namely the patterns for one FD and two overlapping FDs. We calculated the velocity, mass flow rate, wall shear stress, and pressure loss coefficient as well as their change rates for each pattern relative to the no-FD pattern results. The CFD simulation results indicated that the characteristics of the blood flow inside the aneurysm were minimally affected by the deployment of a single FD; in contrast, the overlapping FD pattern results revealed significant changes in the flow. Further, the velocity at an inspection plane within the aneurysm sac decreased by up to 92.2% and 31.0% in the cases of the overlapping and single FD patterns, respectively, relative to the no-FD pattern. The simulations successfully reproduced the hemodynamics, and the qualitative and quantitative investigations are meaningful with regard to the clinical outcomes of overlapped FD deployment.

scholarly journals Numerical and experimental analyses for the improvement of surface instant decontamination technology through biocidal agent dispersion: Potential of application during pandemic

PLoS ONE ◽  
2021 ◽  
Vol 16 (5) ◽  
pp. e0251817
Author(s):  
Paulo Roberto Freitas Neves ◽  
Turan Dias Oliveira ◽  
Tarcísio Faustino Magalhães ◽  
Paulo Roberto Santana dos Reis ◽  
Luzia Aparecida Tofaneli ◽  
...  
Keyword(s):  
Experimental Tests ◽  
Cfd Simulations ◽  
New Device ◽  
Qualitative And Quantitative ◽  
Droplet Concentration ◽  
Computational Fluid Dynamics Cfd ◽  
Suspended Droplet ◽  
The Impact ◽  
Disinfection Chamber ◽  
Important Form

The transmission of SARS-CoV-2 through contact with contaminated surfaces or objects is an important form of transmissibility. Thus, in this study, we evaluated the performance of a disinfection chamber designed for instantaneous dispersion of the biocidal agent solution, in order to characterize a new device that can be used to protect individuals by reducing the transmissibility of the disease through contaminated surfaces. We proposed the necessary adjustments in the configuration to improve the dispersion on surfaces and the effectiveness of the developed equipment. Computational Fluid Dynamics (CFD) simulations of the present technology with a chamber having six nebulizer nozzles were performed and validated through qualitative and quantitative comparisons, and experimental tests were conducted using the method Water-Sensitive Paper (WSP), with an exposure to the biocidal agent for 10 and 30 s. After evaluation, a new passage procedure for the chamber with six nozzles and a new configuration of the disinfection chamber were proposed. In the chamber with six nozzles, a deficiency was identified in its central region, where the suspended droplet concentration was close to zero. However, with the new passage procedure, there was a significant increase in wettability of the surface. With the proposition of the chamber with 12 nozzles, the suspended droplet concentration in different regions increased, with an average increase of 266%. The experimental results of the new configuration proved that there was an increase in wettability at all times of exposure, and it was more significant for an exposure of 30 s. Additionally, even in different passage procedures, there were no significant differences in the results for an exposure of 10 s, thereby showing the effectiveness of the new configuration or improved spraying and wettability by the biocidal agent, as well as in minimizing the impact caused by human factor in the performance of the disinfection technology.

CFD simulation of empty fuel tanks separation from a trainer jet

2020 ◽  
Vol 92 (10) ◽  
pp. 1459-1468
Author(s):  
Aleksander Olejnik ◽  
Adam Dziubiński ◽  
Łukasz Kiszkowiak
Keyword(s):  
Cfd Simulation ◽  
Body Movement ◽  
Cfd Simulations ◽  
Content Type ◽  
Sequential Release ◽  
Wind Tunnel Data ◽  
Computational Fluid Dynamics Cfd ◽  
External Forces ◽  
Additional Value ◽  
Control Surfaces

Purpose This study aims to create 6-degree of freedom (SDOF) for computational fluid dynamics (CFD) simulations of body movement, and to validate using the experimental data for empty tank separation from I-22 Iryda jet trainer. The procedure has an ability to be modified or extended, to simulate, for example, a sequential release from the joints. Design/methodology/approach A set of CFD simulations are calculated. Both the SDOF procedure and the CFD simulation settings are validated using the wind tunnel data available for the aircraft. Findings The simulation using designed procedure gives predictable results, but offers availability to be modified to represent external forces, i.e. from body interaction or control system without necessity to model the control surfaces. Practical implications The procedure could be used to model the separation of external stores and design the deployment of anti-radar chaff, flares or ejection seats. Originality/value The work presents original work, caused by insufficient abilities of original SDOF procedure in ANSYS code. Additional value is the ability of the procedure to be easily modified.

scholarly journals Thermal management of machine compartment in a built-in refrigerator

2018 ◽  
Vol 240 ◽  
pp. 05005
Author(s):  
Milind Devle ◽  
Ankur Garg ◽  
Darci Cavali
Keyword(s):  
Heat Exchange ◽  
Cfd Simulation ◽  
Heat Extraction ◽  
Free Standing ◽  
Cfd Simulations ◽  
Performance Effectiveness ◽  
Hot Air ◽  
Computational Fluid Dynamics Cfd ◽  
Major Factors ◽  
Side Gap

In general a multi-door refrigerator machine compartment comprises of fan, condenser, compressor, control box, drain tray, and drain tubes. The performance of machine compartment depends upon the efficiency of heat extraction or heat exchange from heat generating components such as condenser and compressor. The efficiency of heat exchange can be improved by addressing two major factors, namely (1) Air bypass and (2) Hot air recirculation. The hot air recirculation in the machine compartment for builtin multi-door refrigerator configuration is the focus of this study. The results from Computational Fluid Dynamics (CFD) simulations show that efficiency of heat exchange for built-in application is lower than that for free-standing configuration. Recirculation of hot air and reduction in airflow are the two major factors which contribute towards the variation in machine compartment performance. The CFD simulations were coupled with Partial Factorial Design of Experiment (DoE) approach to systematically investigate the effect of variables such as (a) side gap and top gap between kitchen cabinetry and the refrigerator, (b) the baffle/flap (i.e. back and bottom of machine compartment) on the performance effectiveness of machine compartment. The results of the simulation provided critical design improvement directions resulting in performance improvement. Furthermore, the CFD simulation results were also compared to test data and the results compared favourably.

Transient CFD Visualization of Fossil Fuel Combustion Simulations

2003 ◽  
Author(s):  
Brian Dotson ◽  
Kent Eshenberg ◽  
Chris Guenther ◽  
Thomas O’Brien
Keyword(s):  
Power Plants ◽  
High Efficiency ◽  
Cfd Simulation ◽  
Low Cost ◽  
Three Dimensional ◽  
Cfd Simulations ◽  
Projection System ◽  
Computational Fluid Dynamics Cfd ◽  
High Level ◽  
Wall System

The design of high-efficiency lower-emission coal-fed power plants is facilitated by the extensive use of computational fluid dynamics (CFD) simulations. This paper describes work conducted at the National Energy Technology Laboratory (NETL) and Pittsburgh Supercomputing Center (PSC) to provide an environment for the immersive three-dimensional visualization of CFD simulation results. A low-cost high-resolution projection system has been developed in the visualization lab at NETL. This multi-wall system consists of four projection screens, three of which are tiled into four quadrants. The graphics for the multi-wall system are rendered using a cluster of eight personal computers. A high-level visualization interface named Mavis has also been developed to combine the powerful 3D modules of OpenDX with methods developed at NETL for studying multiphase CFD data. With Python, a completely new OpenDX user interface was built that extends and simplifies the features of a basic graphics library.

Optimal Hardware Placement in a Minitower Computer Enclosure System

2011 ◽  
Author(s):  
M. Alfaro Cano ◽  
A. Hernandez-Guerrero ◽  
C. Rubio Arana ◽  
Aristotel Popescu
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Cfd Simulation ◽  
Operating Temperature ◽  
Optimal Placement ◽  
Cfd Analysis ◽  
Computational Fluid Dynamics Cfd ◽  
Simulation Results ◽  
The Relationship ◽  
Key Questions

One of the requirements for existing personal computers, PCs, is that the hardware inside must maintain an operating temperature as low as possible. One way to achieve that is to place the hardware components at locations with enough airflow around it. However, the relationship between the airflow and temperature of the components is unknown before they are placed at specific locations inside a PC. In this work a Computational Fluid Dynamics (CFD) analysis is coupled to a Design of Experiment (DOE) methodology to answer typical minitower key questions: a) how do the possible positions of hardware components affect their temperature?, and b) is it possible to get an optimal placement for these hardware components using the data collected by the CFD simulation results? The DOE methodology is used to optimize the analysis for a very large number of possible configurations. The results help in identifying where the efforts need to be placed in order to optimize the positioning of the hardware components for similar configurations at the designing stage. Somehow the results show that general conclusions could be drawn, but that there are not specific rules that could be applied to every configuration.

scholarly journals A Workflow for Patient-Individualized Virtual Angiogram Generation Based on CFD Simulation

2012 ◽  
Vol 2012 ◽  
pp. 1-24 ◽  
Author(s):  
Jürgen Endres ◽  
Markus Kowarschik ◽  
Thomas Redel ◽  
Puneet Sharma ◽  
Viorel Mihalef ◽  
...  
Keyword(s):  
Fluid Dynamics ◽  
Blood Flow ◽  
Shear Stress ◽  
Cfd Simulation ◽  
Cerebral Aneurysms ◽  
Patient Specific ◽  
Hemodynamic Parameters ◽  
Risk Of Rupture ◽  
Computational Fluid Dynamics Cfd ◽  
Subsequent Comparison

Increasing interest is drawn on hemodynamic parameters for classifying the risk of rupture as well as treatment planning of cerebral aneurysms. A proposed method to obtain quantities such as wall shear stress, pressure, and blood flow velocity is to numerically simulate the blood flow using computational fluid dynamics (CFD) methods. For the validation of those calculated quantities, virtually generated angiograms, based on the CFD results, are increasingly used for a subsequent comparison with real, acquired angiograms. For the generation of virtual angiograms, several patient-specific parameters have to be incorporated to obtain virtual angiograms which match the acquired angiograms as best as possible. For this purpose, a workflow is presented and demonstrated involving multiple phantom and patient cases.

Simulation on Flow Field and Temperature Field in Water Cooling Tuyere of Blast Furnace

2013 ◽  
Vol 753-755 ◽  
pp. 2709-2712 ◽  
Author(s):  
Ya Na Qie ◽  
Shu Hui Zhang ◽  
Qing Lv ◽  
Li Hong Zhang
Keyword(s):  
Temperature Field ◽  
Economic Benefit ◽  
Cfd Simulation ◽  
Water Pressure ◽  
High Yield ◽  
Maximum Temperature ◽  
Water Cooling ◽  
Direct Motion ◽  
Computational Fluid Dynamics Cfd ◽  
Simulation Results

Life span of water cooling tuyere is one of important factors of blast furnace’s direct motion and high yield. In order to improve the life of tuyere, the flow fleld and temperature field of tuyere were simulated by using computational fluid dynamics (CFD). Simulation results show that the maximum temperature appears at the front margin of tuyere outlet side. The highest temperature of tuyere reduces significantly with the increase of water pressure below 0.4MPa. When the water pressure exceeds 0.4Pa, the highest temperature reduces slowly. In consideration of economic benefit and cooling effect, the best point of inlet pressure is 0.4MPa or so.

scholarly journals Numerical and Experimental Investigation on the Function of Siphons for Tipping-Bucket Rain Gauges

2020 ◽  
Vol 37 (7) ◽  
pp. 1189-1201 ◽  
Author(s):  
Zhao Cai ◽  
Jiufu Liu ◽  
Aimin Liao ◽  
Xuegang Li ◽  
Minhan Liao
Keyword(s):  
Structural Design ◽  
Laboratory Experiments ◽  
Rainfall Intensity ◽  
Outer Part ◽  
Rain Gauge ◽  
Cfd Simulations ◽  
Rain Gauges ◽  
Computational Fluid Dynamics Cfd ◽  
Simulation Results ◽  
Two Parameters

AbstractSiphons can effectively reduce the influence of rainfall intensity on the mechanical bias of tipping-bucket rain gauges (TBRs). To identify the function of siphons for TBRs, this study investigated three types of siphons: a Texas Electronics (TE) siphon, a RIMCO (RIM) siphon, and a Sutron siphon, with both computational fluid dynamics (CFD) simulations and laboratory experiments. To provide better structural designs, further simulations were conducted to adjust two parameters of the siphons: d, the distance from the cap to the outer part, and w, the distance from the main part to the cap part. The simulation results reveal that the most significant advantage of a siphon over a rain gauge collector is to provide stable outflow for the tipping bucket. The stable outflow rates were around 1.5 g s−1 (TE) and 1.55 g s−1 (RIM), while the Sutron siphon increased from 1.75 to 2.45 g s−1. The ratio of stable outflow time to a complete siphon event was 69% (TE), 81% (Sutron), and 83% (RIM). In experiments with rainfall intensity higher than 1 mm min−1, the RIM and TE siphons showed oscillations in the outflow during consecutive siphon events, whereas the Sutron siphon was relatively stable. Further simulations showed that the recommended d and w for the TE siphon are 2.5 and 1.1 mm, respectively, while the recommendations for the RIM siphon are d = 2.5 mm and w = 0.9 mm. The manufacturer’s specifications for d and w are best for the Sutron siphon. These results help to understand the functionality of siphons for TBRs, and benefit the structural design of common siphons.

scholarly journals The Efficient Application of an Impulse Source Wavemaker to CFD Simulations

2019 ◽  
Author(s):  
Pál Schmitt ◽  
Christian Windt ◽  
Josh Davidson ◽  
John V. Ringwood ◽  
Trevor Whittaker
Keyword(s):  
Shallow Water ◽  
Source Function ◽  
Cfd Simulation ◽  
Navier Stokes ◽  
Cfd Simulations ◽  
Wide Range ◽  
Rans Models ◽  
Hydrodynamic Processes ◽  
Computational Fluid Dynamics Cfd ◽  
Shallow Water Models

Computational Fluid Dynamics (CFD) simulations, based on Reynolds Averaged Navier Stokes (RANS) models, are a useful tool for a wide range of coastal and offshore applications, providing a high fidelity representation of the underlying hydrodynamic processes. Generating input waves in the CFD simulation is performed by a numerical wavemaker (NWM), with a variety of different NWM methods existing for this task. While NWMs, based on impulse source methods, have been widely applied for wave generation in depth averaged, shallow water models, they have not seen the same level of adoption in the more general RANS based CFD simulations, due to difficulties in relating the required impulse source function to the resulting free surface elevation for non-shallow water cases. This paper presents an implementation of an impulse source wavemaker, which is able to self-calibrate the impulse source function to produce a desired wave series in deep or shallow water at a specific point in time and space. Example applications are presented, for a numerical wave tank (NWT), based on the opensource CFD software OpenFOAM, for wave packets in deep and shallow water, highlighting the correct calibration of phase and amplitude. Also, the suitability for cases requiring very low reflection from NWT boundaries is demonstrated. Possible issues in the use of the method are discussed and guidance for good application is given.

Evaluate a New Pump Design Using CFD Simulation

2019 ◽  
Author(s):  
Hui Ding ◽  
Benjamin Greenfield
Keyword(s):  
Centrifugal Pump ◽  
Cfd Simulation ◽  
Cfd Simulations ◽  
Pump Design ◽  
Pump Performance ◽  
Simulation Techniques ◽  
Overall Performance ◽  
Design Software ◽  
Simulation Results ◽  
Pump Assembly

Abstract This paper describes how CFD simulations were used to help evaluating a centrifugal pump performance. The simulated pump was designed totally from scratch. Many aspects of pump performance characteristics were predicted based on the geometry generated using a pump design software. Especially the effects of the free spin of the 3rd rotor in a 3 stage pump assembly on overall performance were evaluated. Pump models, simulation techniques, and simulation approaches will be presented in detail. Simulation results will be discussed and compared with available test data.

Sign in / Sign up

Export Citation Format

Share Document