scholarly journals Ratcheting Simulation of a Steel Pipe with Assembly Parts under Internal Pressure and a Cyclic Bending Load

2019 ◽  
Vol 9 (23) ◽  
pp. 5025
Author(s):  
Yang ◽  
Dai ◽  
He
Keyword(s):  
Internal Pressure ◽  
Kinematic Hardening ◽  
Three Dimensional ◽  
Bending Moment ◽  
Element Model ◽  
Steel Pipe ◽  
Cyclic Bending ◽  
Ratcheting Strain ◽  
Bending Load ◽  
Transition Points

The ratcheting behavior of a steel pipe with assembly parts was examined under internal pressure and a cyclic bending load, which has not been seen in previous research. An experimentally validated and three dimensional (3D) elastic-plastic finite element model (FEM)—with a nonlinear isotropic/kinematic hardening model—was used for the pipe’s ratcheting simulation and considered the assembly contact effects outlined in this paper. A comparison of the ratcheting response of pipes with and without assembly parts showed that assembly contact between the sleeve and pipe suppressed the ratcheting response by changing its trend. In this work, the assembly contact effect on the ratcheting response of the pipe with assembly parts is discussed. Both the assembly contact and bending moment were found to control the ratcheting response, and the valley and peak values of the hoop ratcheting strain were the transition points of the two control modes. Finally, while the clearance between the sleeve and the pipe had an effect on the ratcheting response when it was not large, it had no effect when it reached a certain value.

Ratcheting Studies on Type 304LN Stainless Steel Elbows subjected to Combined Internal Pressure and In-Plane Bending Moment

2012 ◽  
Vol 134 (4) ◽  
Author(s):  
S. Vishnuvardhan ◽  
G. Raghava ◽  
P. Gandhi ◽  
M. Saravanan ◽  
D. M. Pukazhendhi ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Internal Pressure ◽  
Accumulation Rate ◽  
Bending Moment ◽  
Cyclic Bending ◽  
Ratcheting Strain ◽  
Bending Load ◽  
304Ln Stainless Steel ◽  
Number Of Cycles ◽  
Opening And Closing

“Ratcheting” is a phenomenon which leads to reduction in fatigue life of a structural component by loss of ductility due to cycle by cycle accumulation of plastic strain. Ratcheting occurs in a structure subjected to a combination of steady/sustained and cyclic loads such that the material response is in inelastic region. Ratcheting studies were carried out on Type 304LN stainless steel elbows, subjected to steady internal pressure and cyclic bending. The elbows filled with water were pressurized between 27.6 MPa and 39.2 MPa. Cyclic bending load, under opening and closing moments, was applied on the elbows at ambient temperature. Number of cycles corresponding to occurrence of a through-wall crack was recorded. Crack was observed in the bent portion at one of the crown locations in all the four specimens. Maximum strain was observed at the intrados and crown locations of the elbows. The ratcheting strain increased with number of cycles at crown and intrados locations. However, the strain accumulation rate decreased with number of cycles. Strain was observed to be minimum at the extrados location and the same stabilized toward the end of the tests. The specimens have failed by occurrence of through-wall axial crack accompanied by simultaneous ballooning. The ballooning was found to be varying from 3.8% to 5.8% with respect to the original circumference in the bent portion. The reduction in thickness was found to be around 12%–15%.

Ratcheting Study of Pressurized Elbows Subjected to Reversed In-Plane Bending

2005 ◽  
Vol 128 (4) ◽  
pp. 525-532 ◽  
Author(s):  
Xu Chen ◽  
Bingjun Gao ◽  
Gang Chen
Keyword(s):  
Internal Pressure ◽  
Kinematic Hardening ◽  
Low Carbon Steel ◽  
Test Machine ◽  
Low Carbon ◽  
Ratcheting Strain ◽  
Bending Load ◽  
Individual Specimen ◽  
Hardening Rules ◽  
Kim Model

With a multi-axial test machine, ratcheting was studied experimentally for pressurized low carbon steel elbows under reversed bending. The maximum ratcheting strain occurred mainly in the hoop direction at flanks. Hoop ratcheting strain was found at intrados for individual specimen. No ratcheting strain was found at the extrados for all tests. Ratcheting strain rate grew with increase of the bending loading level at the same internal pressure or with an increase of internal pressure at the same bending load. Ratcheting simulation was performed by EPFEA with ANSYS in which Ohno-Wang and Chen-Jiao-Kim kinematic hardening rules were applied by user programing. By comparing with the experimental data, it is found that predicted results by the Chen-Jiao-Kim model simulates reasonably. Ratcheting boundary was determined by C-TDF method with the Chen-Jiao-Kim model.

scholarly journals Internal Force on and Deformation of Steel Assembled Supporting Structure of Foundation Pit under Thermal Stress

2021 ◽  
Vol 11 (5) ◽  
pp. 2225
Author(s):  
Fu Wang ◽  
Guijun Shi ◽  
Wenbo Zhai ◽  
Bin Li ◽  
Chao Zhang ◽  
...  
Keyword(s):  
Three Dimensional ◽  
Bending Moment ◽  
High Strength ◽  
Element Model ◽  
Internal Force ◽  
Foundation Pit ◽  
Dimensional Finite Element ◽  
Influence Of Temperature On ◽  
Scale Experiment ◽  
Three Dimensional Finite Element

The steel assembled support structure of a foundation pit can be assembled easily with high strength and recycling value. Steel’s performance is significantly affected by the surrounding temperature due to its temperature sensitivity. Here, a full-scale experiment was conducted to study the influence of temperature on the internal force and deformation of supporting structures, and a three-dimensional finite element model was established for comparative analysis. The test results showed that under the temperature effect, the deformation of the central retaining pile was composed of rigid rotation and flexural deformation, while the adjacent pile of central retaining pile only experienced flexural deformation. The stress on the retaining pile crown changed little, while more stress accumulated at the bottom. Compared with the crown beam and waist beam 2, the stress on waist beam 1 was significantly affected by the temperature and increased by about 0.70 MPa/°C. Meanwhile, the stress of the rigid panel was greatly affected by the temperature, increasing 78% and 82% when the temperature increased by 15 °C on rigid panel 1 and rigid panel 2, respectively. The comparative simulation results indicated that the bending moment and shear strength of pile 1 were markedly affected by the temperature, but pile 2 and pile 3 were basically stable. Lastly, as the temperature varied, waist beam 2 had the largest change in the deflection, followed by waist beam 1; the crown beam experienced the smallest change in the deflection.

Ratcheting assessment of corroded elbow pipes subjected to internal pressure and cyclic bending moment

2021 ◽  
pp. 030932472198989
Author(s):  
Ali Salehi ◽  
Armin Rahmatfam ◽  
Mohammad Zehsaz
Keyword(s):  
Growth Rate ◽  
Stainless Steel ◽  
Internal Pressure ◽  
Bending Moment ◽  
Axial Direction ◽  
Hoop Strain ◽  
Cyclic Bending ◽  
High Fatigue ◽  
The Impact ◽  
Cyclic Bending Moment

The present study aimed to study ratcheting strains of corroded stainless steel 304LN elbow pipes subjected to internal pressure and cyclic bending moment. To this aim, spherical and cubical shapes corrosion are applied at two depths of 1 mm and 2 mm in the critical points of elbow pipe such as symmetry sites at intrados, extrados, and crown positions. Then, a Duplex 2205 stainless steel elbow pipe is considered as an alternative to studying the impact of the pipe materials, due to its high corrosion resistance and strength, toughness, and most importantly, the high fatigue strength and other mechanical properties than stainless steel 304LN. In order to perform numerical analyzes, the hardening coefficients of the materials were calculated. The results highlight a significant relationship between the destructive effects of corrosion and the depth and shape of corrosion, so that as corrosion increases, the resulting destructive effects increases as well, also, the ratcheting strains in cubic corrosions have a higher growth rate than spherical corrosions. In addition, the growth rate of the ratcheting strains in the hoop direction is much higher across the studied sample than the axial direction. The highest growth rate of hoop strain was observed at crown and the highest growth rate of axial strains occurred at intrados position. Altogether, Duplex 2205 material has a better performance than SS 304LN.

Shakedown Limit Load Determination for a Kinematically Hardening 90-Degree Pipe Bend Subjected to Constant Internal Pressure and Cyclic Bending

2007 ◽  
Author(s):  
Hany F. Abdalla ◽  
Mohammad M. Megahed ◽  
Maher Y. A. Younan
Keyword(s):  
Finite Element ◽  
Internal Pressure ◽  
Plastic Material ◽  
Kinematic Hardening ◽  
Limit Load ◽  
Material Behavior ◽  
Pipe Bend ◽  
Cyclic Bending ◽  
Perfectly Plastic ◽  
Shakedown Limit

A simplified technique for determining the shakedown limit load of a structure employing an elastic-perfectly-plastic material behavior was previously developed and successfully applied to a long radius 90-degree pipe bend. The pipe bend is subjected to constant internal pressure and cyclic bending. The cyclic bending includes three different loading patterns namely; in-plane closing, in-plane opening, and out-of-plane bending moment loadings. The simplified technique utilizes the finite element method and employs small displacement formulation to determine the shakedown limit load without performing lengthy time consuming full cyclic loading finite element simulations or conventional iterative elastic techniques. In the present paper, the simplified technique is further modified to handle structures employing elastic-plastic material behavior following the kinematic hardening rule. The shakedown limit load is determined through the calculation of residual stresses developed within the pipe bend structure accounting for the back stresses, determined from the kinematic hardening shift tensor, responsible for the translation of the yield surface. The outcomes of the simplified technique showed very good correlation with the results of full elastic-plastic cyclic loading finite element simulations. The shakedown limit moments output by the simplified technique are used to generate shakedown diagrams of the pipe bend for a spectrum of constant internal pressure magnitudes. The generated shakedown diagrams are compared with the ones previously generated employing an elastic-perfectly-plastic material behavior. These indicated conservative shakedown limit moments compared to the ones employing the kinematic hardening rule.

Flexible Riser Top Connection Analysis With I-Tube Interface and Bending Hysteresis Effect

2019 ◽  
Author(s):  
Yangye He ◽  
Hailong Lu ◽  
Murilo Augusto Vaz ◽  
Marcelo Caire
Keyword(s):  
Kinematic Hardening ◽  
Bending Moment ◽  
Element Model ◽  
Beam Model ◽  
Flexible Riser ◽  
Nonlinear Bending ◽  
Cross Sectional ◽  
Irregular Wave ◽  
Global Dynamic ◽  
Curvature Distribution

Abstract The flexible riser top connection to the floating production platform is a critical region for fatigue lifetime (re)assessment. The interface with the I-tube and its curved sleeve combined with the gap between the riser and bend stiffener may lead to different curvature distribution when compared to the traditional modeling approach that considers the bend stiffener attached to the pipe. For a more accurate top connection assessment, the flexible riser bending hysteresis can also be directly incorporated in the global dynamic analysis helping to reduce curvature amplitude and lifetime prediction conservatism. This work investigates a 7” flexible riser-bend stiffener top connection with I-tube interface by performing irregular wave global dynamic analyses with the OrcaFlex package and considering a nonlinear bending moment vs curvature riser behavior obtained from a detailed cross sectional model developed in Abaqus. OrcaFlex curvature distribution results are also compared with a quasi-static finite element model that uses an elasto-plastic formulation with kinematic hardening to represent riser hysteresis through an equivalent beam model. A good curvature distribution correlation is observed for both top connection models (OrcaFlex x Abaqus) in the bend stiffener area with reduced amplitudes when riser bending hysteresis is considered.

Effect of Circumferential Location of Local Wall Thinning Defect on the Collapse Moment of Elbow

2006 ◽  
Author(s):  
Jin Weon Kim ◽  
Yeon Soo Na ◽  
Chi Yong Park
Keyword(s):  
Carbon Steel ◽  
Internal Pressure ◽  
Nuclear Power ◽  
Three Dimensional ◽  
Piping System ◽  
Main Concern ◽  
Wall Thinning ◽  
Bending Load ◽  
Local Wall Thinning ◽  
Steel Piping

Local wall-thinning due to flow-accelerated corrosion is one of the degradation mechanisms of carbon steel piping in nuclear power plant (NPP). It is a main concern in carbon steel piping systems in terms of the safety and operability of the NPP. Recently, the integrity of piping components containing local wall-thinning has become more important for maintaining the reliability of a nuclear piping system, and has been the subject of several studies. However, although wall-thinning in pipe bends and elbows has been frequently reported, its effect on the integrity of pipe bends and elbows has not yet been systematically investigated. Thus, the purpose of this study was to investigate the effect of the circumferential location of a local wall-thinning defect on the collapse behavior of an elbow. For this purpose, the present study used three-dimensional finite element analyses on a 90-degree elbow containing local wall-thinning at the crown of the bend region and evaluated the collapse moment of the wall-thinned elbow under various thinning geometries and loading conditions. The combined internal pressure and bending loads were considered as an applied load. Internal pressure of 0∼20 MPa and both closing-and opening-mode bending were applied. The results of the analyses showed that a reduction in the collapse moment of the elbow due to local wall-thinning was more significant when a defect was located at the crown than when a defect was located at the intrados and extrados. Also, the effect of the internal pressure on the collapse moment depended on the circumferential location of the thinning defect and mode of the bending load.

scholarly journals Micromechanical Modelling of the Cyclic Deformation Behavior of Martensitic SAE 4150—A Comparison of Different Kinematic Hardening Models

Metals ◽  
2019 ◽  
Vol 9 (3) ◽  
pp. 368 ◽  
Author(s):  
Benjamin Schäfer ◽  
Xiaochen Song ◽  
Petra Sonnweber-Ribic ◽  
Hamad ul Hassan ◽  
Alexander Hartmaier
Keyword(s):  
Kinematic Hardening ◽  
Three Dimensional ◽  
High Strength ◽  
Element Model ◽  
Calibration Procedure ◽  
Cyclic Stress ◽  
System Level ◽  
Strain Behavior ◽  
Hardening Models ◽  
Mean Stress Relaxation

A fundamental prerequisite for the micromechanical simulation of fatigue is the appropriate modelling of the effective cyclic properties of the considered material. Therefore, kinematic hardening formulations on the slip system level are of crucial importance due to their fundamental relevance in cyclic material modelling. The focus of this study is the comparison of three different kinematic hardening models (Armstrong Frederick, Chaboche, and Ohno–Wang). In this work, investigations are performed on the modelling and prediction of the cyclic stress-strain behavior of the martensitic high-strength steel SAE 4150 for two different total strain ratios (R ε = −1 and R ε = 0). In the first step, a three-dimensional martensitic microstructure model is developed by using multiscale Voronoi tessellations. Based on this martensitic representative volume element, micromechanical simulations are performed by a crystal plasticity finite element model. For the constitutive model calibration, a new multi-objective calibration procedure incorporating a sensitivity analysis as well as an evolutionary algorithm is presented. The numerical results of different kinematic hardening models are compared to experimental data with respect to the appropriate modelling of the Bauschinger effect and the mean stress relaxation behavior at R ε = 0. It is concluded that the Ohno–Wang model is superior to the Armstrong Frederick and Chaboche kinematic hardening model at R ε = −1 as well as at R ε = 0.

Finite Element Analysis of Flange Joint With Single and Twin Gaskets Under External Bending Load

2015 ◽  
Author(s):  
N. Rino Nelson ◽  
N. Siva Prasad ◽  
A. S. Sekhar
Keyword(s):  
Finite Element ◽  
Work Performance ◽  
Elevated Temperatures ◽  
Bending Moment ◽  
Element Model ◽  
Pressure Vessels ◽  
Flange Joint ◽  
Element Analysis ◽  
Bending Load ◽  
Gasket Material

Gasketed flange joint is a vital component in pressure vessels and piping systems. Flange joint is usually subjected to bending load due to expansion, wind load, self-weight, etc. Most of the flange design methods use equivalent pressure to include the effect of external bending loads. It becomes complex when the joint is subjected to bending load at elevated temperatures, due to the nonlinear behavior of gasket material. In the present work, performance of the flange joint has been studied under external bending load at elevated temperatures. A 3D finite element model is developed, considering the nonlinearities in the joint due to gasket material and contact between its members along with their temperature dependent material properties. The performance of the joint under different bolt preloads, internal fluid pressures and temperatures is studied. Flange joint with two gaskets (twin gasketed joint) placed beside each other radially, is also analyzed under external bending moment. The maximum allowable bending moments at different internal temperatures, for single and twin gasketed joints with spiral wound gasket are arrived.

Finite Element Prediction of Mechanical Behaviour under Bending of Honeycomb Sandwich Panels

2014 ◽  
Vol 980 ◽  
pp. 81-85 ◽  
Author(s):  
Kaoua Sid-Ali ◽  
Mesbah Amar ◽  
Salah Boutaleb ◽  
Krimo Azouaoui
Keyword(s):  
Finite Element ◽  
Mechanical Behaviour ◽  
Three Dimensional ◽  
Sandwich Panels ◽  
Element Model ◽  
Shell Elements ◽  
Numerical Characterization ◽  
Bending Load ◽  
Accurate Stress Analysis ◽  
Three Dimensional Finite Element

This paper outlines a finite element procedure for predicting the mechanical behaviour under bending of sandwich panels consisting of aluminium skins and aluminium honeycomb core. To achieve a rapid and accurate stress analysis, the sandwich panels have been modelled using shell elements for the skins and the core. Sandwich panels were modelled by a three-dimensional finite element model implemented in Abaqus/Standard. By this model the influence of the components on the behaviour of the sandwich panel under bending load was evaluated. Numerical characterization of the sandwich structure, is confronted to both experimental and homogenization technique results.

Sign in / Sign up

Export Citation Format

Share Document