scholarly journals Centrifugally Spun α-Fe2O3/TiO2/Carbon Composite Fibers as Anode Materials for Lithium-Ion Batteries

2019 ◽  
Vol 9 (19) ◽  
pp. 4032 ◽  
Author(s):  
Luis Zuniga ◽  
Gabriel Gonzalez ◽  
Roberto Orrostieta Chavez ◽  
Jason C. Myers ◽  
Timothy P. Lodge ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Electrochemical Performance ◽  
Lithium Ion Batteries ◽  
Specific Capacity ◽  
Lithium Ion ◽  
Composite Fiber ◽  
Carbon Composite ◽  
Composite Fibers ◽  
X Ray ◽  
Binder Free

We report results on the electrochemical performance of flexible and binder-free α-Fe2O3/TiO2/carbon composite fiber anodes for lithium-ion batteries (LIBs). The composite fibers were produced via centrifugal spinning and subsequent thermal processing. The fibers were prepared from a precursor solution containing PVP/iron (III) acetylacetonate/titanium (IV) butoxide/ethanol/acetic acid followed by oxidation at 200 °C in air and then carbonization at 550 °C under flowing argon. The morphology and structure of the composite fibers were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy dispersive X-ray spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS), and thermogravimetric analysis (TGA). These ternary composite fiber anodes showed an improved electrochemical performance compared to the pristine TiO2/C and α-Fe2O3/C composite fiber electrodes. The α-Fe2O3/TiO2/C composite fibers also showed a superior cycling performance with a specific capacity of 340 mAh g−1 after 100 cycles at a current density of 100 mA g−1, compared to 61 mAh g−1 and 121 mAh g−1 for TiO2/C and α-Fe2O3/C composite electrodes, respectively. The improved electrochemical performance and the simple processing of these metal oxide/carbon composite fibers make them promising candidates for the next generation and cost-effective flexible binder-free anodes for LIBs.

scholarly journals EG-Assisted Synthesis and Electrochemical Performance of Ultrathin Carbon-Coated LiMnPO4Nanoplates as Cathodes in Lithium Ion Batteries

2015 ◽  
Vol 2015 ◽  
pp. 1-8
Author(s):  
Liwei Su ◽  
Yali Sha ◽  
Jingkang Jiang ◽  
Lianbang Wang ◽  
Yuanhao Wang
Keyword(s):  
Electron Microscopy ◽  
Electrochemical Performance ◽  
Lithium Ion Batteries ◽  
Lithium Ion ◽  
X Ray Diffraction ◽  
Electrochemical Behaviors ◽  
X Ray ◽  
Pyrolysis Method ◽  
Transmission Electron ◽  
Carbon Coated

Ultrathin carbon-coated LiMnPO4(ULMP/C) nanoplates were prepared through an ethylene glycol- (EG-) assisted pyrolysis method. Different from most of LiMnPO4/C works, the obtained ULMP/C possessed relatively small particle size (less than 50 nm in thickness) and preferable carbon coating (~1 nm in thickness, 2 wt.%). As a reference, LiMnPO4/C (LMP/C) composites were also fabricated via the traditional hydrothermal method. X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy dispersive X-ray spectroscopy (EDS), thermogravimetric analysis (TG), galvanostatic charge-discharge, and cyclic voltammetry (CV) were performed to characterize the crystalline phase, morphology, structure, carbon content, and electrochemical behaviors of samples. The electrochemical performance of bare and carbon-coated LiMnPO4was evaluated as cathodes in lithium ion batteries. As a result, the obtained ULMP/C nanoplates demonstrated much higher reversible capacities (110.9 mAh g−1after 50 cycles at 0.1 C) and rate performances than pure LMP and LMP/C composites. This facile and efficient EG-assisted pyrolysis method can enlighten us on exploiting advanced routes to modify active materials with ultrathin and homogeneous carbon layers.

scholarly journals Improvement of long-term cycling performance of high-nickel cathode materials by ZnO coating

2021 ◽  
Vol 10 (1) ◽  
pp. 210-220
Author(s):  
Fangfang Wang ◽  
Ruoyu Hong ◽  
Xuesong Lu ◽  
Huiyong Liu ◽  
Yuan Zhu ◽  
...  
Keyword(s):  
Electrochemical Performance ◽  
Lithium Ion Batteries ◽  
Solid Phase ◽  
Low Cost ◽  
Specific Capacity ◽  
High Capacity ◽  
Lithium Ion ◽  
Side Reaction ◽  
Chemical Route ◽  
High Nickel

Abstract The high-nickel cathode material of LiNi0.8Co0.15Al0.05O2 (LNCA) has a prospective application for lithium-ion batteries due to the high capacity and low cost. However, the side reaction between the electrolyte and the electrode seriously affects the cycling stability of lithium-ion batteries. In this work, Ni2+ preoxidation and the optimization of calcination temperature were carried out to reduce the cation mixing of LNCA, and solid-phase Al-doping improved the uniformity of element distribution and the orderliness of the layered structure. In addition, the surface of LNCA was homogeneously modified with ZnO coating by a facile wet-chemical route. Compared to the pristine LNCA, the optimized ZnO-coated LNCA showed excellent electrochemical performance with the first discharge-specific capacity of 187.5 mA h g−1, and the capacity retention of 91.3% at 0.2C after 100 cycles. The experiment demonstrated that the improved electrochemical performance of ZnO-coated LNCA is assigned to the surface coating of ZnO which protects LNCA from being corroded by the electrolyte during cycling.

scholarly journals The Synthesis and Electrochemical Performance of Si Composite with Hollow Carbon Microtubes by the Carbonization of Milkweed from Nature as Anode Template for Lithium Ion Batteries

Energies ◽  
2020 ◽  
Vol 13 (19) ◽  
pp. 5124
Author(s):  
Eun Hyuk Chung ◽  
Jong Pil Kim ◽  
Hyun Gyu Kim ◽  
Jae-Min Chung ◽  
Sei-Jin Lee ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Electrical Conductivity ◽  
Electrochemical Performance ◽  
Pore Size ◽  
Lithium Ion Batteries ◽  
Polyvinylidene Fluoride ◽  
Lithium Ion ◽  
Size Analysis ◽  
Pore Size Analysis ◽  
Hollow Carbon

It has been reported that improving electrical conductivity and maintaining stable structure during discharge/charge process are challenge for Si to be used as an anode for lithium ion batteries (LIB). To address this problem, milkweed (MW) was carbonized to prepare hollow carbon microtubes (HCMT) derived from biomass as an anode template for LIB. In order to improve electrical conductivity, various materials such as chitosan (CTS), agarose, and polyvinylidene fluoride (PVDF) are used as carbon source (C1, C2, and C3) by carbonization. Carbon coated HCMT@Si composits, HCMT@Si@C1, HCMT@Si@C1@C2, and HCMT@Si@C1@C3, have been successfully synthesized. Changes in structure and crystallinity of HCMT@Si composites were characterized by using X-ray diffraction (XRD). Specific surface area for samples was calculated by using BET (Brunauer–Emmett–Teller). Also, pore size and particle size were obtained by particle and pore size analysis system. The surface morphology was evaluated using high resolution scanning electron microscopy (HR-SEM), Field Emission transmission electron microscopy (TEM). The thermal properties of HCMT@Si composites were analyzed by thermogravimetric analysis (TGA). Our research was performed to study the synthesis and electrochemical performance of Si composite with HCMT by the carbonization of natural micro hollow milkweed to form an inner space. After carbonization at 900 °C for 2 h in N2 flow, inner diameter of HCMT obtained was about 10 μm. The electrochemical tests indicate that HCMT@Si@C1@C3 exhibits discharge capacity of 932.18 mAh/g at 0.5 A/g after 100 cycles.

scholarly journals The influence of different Si : C ratios on the electrochemical performance of silicon/carbon layered film anodes for lithium-ion batteries

RSC Advances ◽  
2018 ◽  
Vol 8 (12) ◽  
pp. 6660-6666 ◽  
Author(s):  
Jun Wang ◽  
Shengli Li ◽  
Yi Zhao ◽  
Juan Shi ◽  
Lili Lv ◽  
...  
Keyword(s):  
Electrochemical Performance ◽  
Lithium Ion Batteries ◽  
Anode Materials ◽  
Specific Capacity ◽  
Lithium Ion ◽  
Lithium Ions ◽  
High Specific Capacity ◽  
Silicon Carbon ◽  
Silicon Based

With a high specific capacity (4200 mA h g−1), silicon based materials have become the most promising anode materials in lithium-ions batteries.

Enhanced electrochemical performance of lithium ion batteries using Sb2S3 nanorods wrapped in graphene nanosheets as anode materials

Nanoscale ◽  
2018 ◽  
Vol 10 (7) ◽  
pp. 3159-3165 ◽  
Author(s):  
Yucheng Dong ◽  
Shiliu Yang ◽  
Zhenyu Zhang ◽  
Jong-Min Lee ◽  
Juan Antonio Zapien
Keyword(s):  
Electrochemical Performance ◽  
Lithium Ion Batteries ◽  
Anode Materials ◽  
Graphene Nanosheets ◽  
Specific Capacity ◽  
Lithium Ion ◽  
Lithium Insertion ◽  
Insertion Reactions ◽  
Theoretical Specific Capacity ◽  
Enhanced Electrochemical Performance

Antimony sulfide can be used as a promising anode material for lithium ion batteries due to its high theoretical specific capacity derived from sequential conversion and alloying lithium insertion reactions.

scholarly journals The Use of Succinonitrile as an Electrolyte Additive for Composite-Fiber Membranes in Lithium-Ion Batteries

Membranes ◽  
2020 ◽  
Vol 10 (3) ◽  
pp. 45 ◽  
Author(s):  
Jahaziel Villarreal ◽  
Roberto Orrostieta Chavez ◽  
Sujay A. Chopade ◽  
Timothy P. Lodge ◽  
Mataz Alcoutlabi
Keyword(s):  
Ionic Liquid ◽  
Ionic Conductivity ◽  
Lithium Ion Batteries ◽  
Specific Capacity ◽  
Lithium Ion ◽  
Composite Fiber ◽  
Galvanostatic Charge ◽  
Lithium Anode ◽  
Charge Discharge ◽  
Licoo2 Cathode

In the present work, the effect of temperature and additives on the ionic conductivity of mixed organic/ionic liquid electrolytes (MOILEs) was investigated by conducting galvanostatic charge/discharge and ionic conductivity experiments. The mixed electrolyte is based on the ionic liquid (IL) (EMI/TFSI/LiTFSI) and organic solvents EC/DMC (1:1 v/v). The effect of electrolyte type on the electrochemical performance of a LiCoO2 cathode and a SnO2/C composite anode in lithium anode (or cathode) half-cells was also investigated. The results demonstrated that the addition of 5 wt.% succinonitrile (SN) resulted in enhanced ionic conductivity of a 60% EMI-TFSI 40% EC/DMC MOILE from ~14 mS·cm−1 to ~26 mS·cm−1 at room temperature. Additionally, at a temperature of 100 °C, an increase in ionic conductivity from ~38 to ~69 mS·cm−1 was observed for the MOILE with 5 wt% SN. The improvement in the ionic conductivity is attributed to the high polarity of SN and its ability to dissolve various types of salts such as LiTFSI. The galvanostatic charge/discharge results showed that the LiCoO2 cathode with the MOILE (without SN) exhibited a 39% specific capacity loss at the 50th cycle while the LiCoO2 cathode in the MOILE with 5 wt.% SN showed a decrease in specific capacity of only 14%. The addition of 5 wt.% SN to the MOILE with a SnO2/C composite-fiber anode resulted in improved cycling performance and rate capability of the SnO2/C composite-membrane anode in lithium anode half-cells. Based on the results reported in this work, a new avenue and promising outcome for the future use of MOILEs with SN in lithium-ion batteries (LIBs) can be opened.

scholarly journals Atomic Layer Deposition of Lithium–Nickel–Silicon Oxide Cathode Material for Thin-Film Lithium-Ion Batteries

Energies ◽  
2020 ◽  
Vol 13 (9) ◽  
pp. 2345
Author(s):  
Maxim Maximov ◽  
Denis Nazarov ◽  
Aleksander Rumyantsev ◽  
Yury Koshtyal ◽  
Ilya Ezhov ◽  
...  
Keyword(s):  
Thin Film ◽  
Electron Microscopy ◽  
Atomic Layer Deposition ◽  
Lithium Ion Batteries ◽  
Silicon Oxide ◽  
Lithium Ion ◽  
Atomic Layer ◽  
X Ray ◽  
Layer Deposition ◽  
Nickel Silicon

Lithium nickelate (LiNiO2) and materials based on it are attractive positive electrode materials for lithium-ion batteries, owing to their large capacity. In this paper, the results of atomic layer deposition (ALD) of lithium–nickel–silicon oxide thin films using lithium hexamethyldisilazide (LiHMDS) and bis(cyclopentadienyl) nickel (II) (NiCp2) as precursors and remote oxygen plasma as a counter-reagent are reported. Two approaches were studied: ALD using supercycles and ALD of the multilayered structure of lithium oxide, lithium nickel oxide, and nickel oxides followed by annealing. The prepared films were studied by scanning electron microscopy, spectral ellipsometry, X-ray diffraction, X-ray reflectivity, X-ray photoelectron spectroscopy, time-of-flight secondary ion mass spectrometry, energy-dispersive X-ray spectroscopy, transmission electron microscopy, and selected-area electron diffraction. The pulse ratio of LiHMDS/Ni(Cp)2 precursors in one supercycle ranged from 1/1 to 1/10. Silicon was observed in the deposited films, and after annealing, crystalline Li2SiO3 and Li2Si2O5 were formed at 800 °C. Annealing of the multilayered sample caused the partial formation of LiNiO2. The obtained cathode materials possessed electrochemical activity comparable with the results for other thin-film cathodes.

Sign in / Sign up

Export Citation Format

Share Document