scholarly journals The Hay Inclined Plane in Coalbrookdale (Shropshire, England): Analysis through Computer-Aided Engineering

2019 ◽  
Vol 9 (16) ◽  
pp. 3385 ◽  
Author(s):  
José Rojas-Sola ◽  
Eduardo De la Morena-De la Fuente
Keyword(s):  
Elastic Limit ◽  
Computer Aided Engineering ◽  
Operating Conditions ◽  
Von Mises Stress ◽  
Inclined Plane ◽  
Maximum Displacement ◽  
Emergency Braking ◽  
Maximum Value ◽  
Computer Aided ◽  
Von Mises

This article analyzes the ‘Hay inclined plane’ designed by the English engineer and entrepreneur William Reynolds and put into operation in 1792 to facilitate the transport of vessels between channels at different levels using an inclined plane. To this end, a study of computer-aided engineering (CAE) was carried out using the parametric software Autodesk Inventor Professional, consisting of a static analysis using the finite-element method (FEM) of the 3D model of the invention under real operating conditions. The results obtained after subjecting the mechanism to the two most unfavorable situations (blockage situation of the inertia flywheel and emergency braking situation) indicate that, with the exception of the braking bar, the rest of the assembly is perfectly designed and dimensioned. In particular, for the blockage situation, the point with the greatest stress is at the junction between the inertia flywheel and the axle to which it is attached, the maximum value of von Mises stress being at that point (186.9 MPa) lower than the elastic limit of the cast iron. Also, at this point the deformation is very low (0.13% of its length), as well as the maximum displacement that takes place in the inertia flywheel itself (22.98 mm), and the lowest safety factor has a value of 3.51 (located on the wooden shaft support), which indicates that the mechanism is clearly oversized. On the other hand, the emergency braking situation, which is technically impossible with a manual operation, indicates that the braking bar supports a maximum von Mises stress of 1025 MPa, above the elastic limit of the material, so it would break. However, other than that element, the rest of the elements have lower stresses, with a maximum value of 390.7 MPa, and with safety factors higher than 1.7, which indicates that the mechanism was well dimensioned.

scholarly journals The Conical Stones Olive Oil Mill: Analysis through Computer-Aided Engineering

Agriculture ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 255 ◽  
Author(s):  
José Ignacio Rojas-Sola ◽  
Eduardo De la Morena-De la Fuente
Keyword(s):  
Olive Oil ◽  
Computer Aided Engineering ◽  
Operating Conditions ◽  
Frame Structure ◽  
Von Mises Stress ◽  
Maximum Displacement ◽  
Safety Coefficient ◽  
A Value ◽  
Computer Aided ◽  
Von Mises

This article analyzes an olive oil mill formed of four conical stones used in the milling of the olive. To this end, a study of computer-aided engineering (CAE) was carried out using the parametric software Autodesk Inventor Professional, consisting of a static analysis using the finite-element method (FEM) of the three-dimensional (3D) model of the mill under real operating conditions. The results obtained revealed that the conical stones mill was a very robust machine. When studying the assembly in the most unfavorable situation (blockage of one of its millstones), we observed that the element with the highest von Mises stress was the bearing nut, reaching a value of 263.9 MPa, which was far from the elastic limit of cast iron (758 MPa). On the other hand, the machine hardly presented any equivalent deformations or displacements that could jeopardize the operation as a whole. The maximum displacement obtained was 2.494 mm in the inertia flywheel, and the equivalent deformations did not reach 0.1% of the part dimension. Similarly, the element with the lowest safety coefficient (2.87) was the same bearing nut with the highest von Mises stress, although the next element with the second lowest safety coefficient had a value of 8.69, which showed that the set was clearly oversized. These results demonstrate the convenience of redesigning the set in order to resize some of its elements, and that they could have lower safety coefficients of between 2 and 4. After an initial analysis, the resizable elements would fundamentally be those related to the movement transmission system and the frame structure.

scholarly journals The Tower Press for Obtaining Olive Oil: Analysis through Computer-Aided Engineering

Agriculture ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 554
Author(s):  
José Ignacio Rojas-Sola ◽  
Eduardo De la Morena-De la Fuente ◽  
Manuel Jesús Hermoso-Orzáez ◽  
David Hernández-Díaz
Keyword(s):  
Olive Oil ◽  
Static Analysis ◽  
Computer Aided Engineering ◽  
Operating Conditions ◽  
Von Mises Stress ◽  
Screw Thread ◽  
Maximum Displacement ◽  
Safety Coefficient ◽  
Computer Aided ◽  
Von Mises

This article analyzes a large tower press used to press crushed olives to obtain olive oil. To this end, a study of computer-aided engineering (CAE) was carried out using the parametric software Autodesk Inventor Professional, consisting of a static analysis using the finite-element method (FEM) of the 3D model of the press under real operating conditions. The tower press has been analyzed in two limit positions: in the rest position, supported on two pillars, and the pressing position, supported on the set of filter discs (basket load) called ‘cargo de capachos’ that contained the previously ground olives. In the first position, static analysis revealed that the maximum von Mises stress was 22.7 MPa, located on the axle of the roller, but this is far from the elastic limit. Moreover, the lowest safety coefficient is 11.16, produced in the contact between the tower and the right pillar and well above the optimal range between 2 and 4. On the other hand, it hardly presents equivalent displacements or deformations that would endanger the operation of the set. The greatest displacement would be in the wooden guide (0.123 mm) and a deformation of 0.027% with respect to its length. These values confirm that, in this position, the tower press was clearly oversized. However, the results obtained regarding the second position are not entirely conclusive. Although the values of the displacements and the equivalent deformations are low, with results similar to those obtained in the first position, with a maximum displacement of 0.1315 mm located in the horizontal beam of the support structure and a maximum equivalent deformation of value 0.385%, located in the contact between the screw and the nut, the same does not happen with the von Mises stress. The software did not obtain a convergent result due to the frustoconical geometry of the bolt that joins the screw and nut, adopting a maximum value of 508.3 MPa. For this point, the safety coefficient is 1.49, which reveals a sizing problem with the proposed solution of resizing the screw thread, giving it more robustness. The rest of the elements work with a safety coefficient above 4.33 so they are also clearly oversized, according to current criteria.

scholarly journals Agustín de Betancourt’s Double-Acting Steam Engine: Analysis through Computer-Aided Engineering

2018 ◽  
Vol 8 (11) ◽  
pp. 2309 ◽  
Author(s):  
José Rojas-Sola ◽  
Eduardo De la Morena-De la Fuente
Keyword(s):  
Industrial Revolution ◽  
Computer Aided Engineering ◽  
Point Of View ◽  
Operating Conditions ◽  
Steam Engine ◽  
Von Mises Stress ◽  
Industrial Archaeology ◽  
3D Cad ◽  
Computer Aided ◽  
Von Mises

This article analyses the double-acting steam engine designed by Agustín de Betancourt in 1789 and based on the steam engine of James Watt. Its novelty and scientific interest lies in the fact that from the point of view of industrial archaeology and the study of technical historical heritage there is no worldwide study on this invention, which marked a historic milestone in the design of the steam engines of the Industrial Revolution (1760–1840). This underscores the utility and originality of this research. To this end, a study of computer-aided engineering (CAE) was carried out using the parametric software Autodesk Inventor Professional, consisting of a static analysis using the finite-element method of the 3D CAD model of the invention under real operating conditions. The results have shown that the double-acting steam engine was correctly designed considering that the values of the maximum von Mises stress (188.4 MPa) obtained were taken away from the elastic limit of the material it was made of (cast iron), as well as to the maximum deformations (0.14% with respect to its length) obtained in the same element that presents the maximum stress (opening axle of the high pressure steam valve). Similarly, the maximum displacements (18.74 mm) are located in the mobile counterweights that transmit certain inertia to facilitate the opening and closing of the valves. Finally, if we look at the results of the safety coefficient, whose lowest value was 4.02, we could say that the invention was oversized, following constructive criteria of the time, as there were no resistance tests on materials that would help in the optimization of the design of the invention.

scholarly journals Analysis of Tube Design for Clean Water from Stainless Steel 304 and 201

2021 ◽  
Vol 1 (1) ◽  
Author(s):  
Muhammad Amin Putro ◽  
Prantasi Harmi Tjahjanti
Keyword(s):  
Stainless Steel ◽  
Safety Factor ◽  
Pure Water ◽  
Von Mises Stress ◽  
Maximum Displacement ◽  
Maximum Value ◽  
Stainless Steel 304 ◽  
Thickness Variations ◽  
Von Mises ◽  
Ss 304

This study aims to design the water tube for pure water namely a set of processing tools used to place the water using Autodesk Inventor 2016 software. The data which inputted is stainless steel SS 304 and SS 201, because both of them have the Cr and Ni elements, which will be used as tubes and the top and bottom caps. The results of running data are von mises stress, displacement, and safety factor. The output data were used to obtain the most efficient material and thickness variations between 1.5mm, 2mm, and 3mm. The most suitable and efficient result shown at 3mm thick SS 304 with the maximum value of von mises stress is 14.62 MPa, a maximum displacement of 0.013mm, and a safety factor of 15.

scholarly journals Agustin de Betancourt’s Mechanical Dredger in the Port of Kronstadt: Analysis through Computer-Aided Engineering

2018 ◽  
Vol 8 (8) ◽  
pp. 1338 ◽  
Author(s):  
José Rojas-Sola ◽  
Eduardo De la Morena-De la Fuente
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
3D Model ◽  
Russian Empire ◽  
Computer Aided Engineering ◽  
Operating Conditions ◽  
The Finite Element Method ◽  
Safety Coefficient ◽  
Computer Aided ◽  
The Russian Empire

This article analyzes the first self-propelled floating dredging machine designed and executed by Agustín de Betancourt in 1810 to dredge the port of Kronstadt (Russia). With this objective, a study of computer-aided engineering (CAE) has been carried out using the parametric software Autodesk Inventor Professional, consisting of a static analysis using the finite element method, of the 3D model which is reliable under operating conditions. The results have shown that the system of inertia drums proposed by Betancourt manages to dissipate the tensions between the different elements, locating the highest stresses in the links of the bucket rosary, specifically at the point of contact between links. Similarly, the maximum displacements and the greatest deformations (always associated with these points of greater stress), are far from reaching the limits of breakage of the material used in its construction, as well as the safety coefficient of the invention, confirming that the mechanism was oversized, as was generally the case at the time. This analysis highlights the talent of the Spanish engineer and his mastery of mechanics, in an invention, the first of its kind worldwide, which served the Russian Empire for many years.

A Method for Creating a Manufacturing Cost Heatmap Based Purely on Part Geometry

2018 ◽  
Author(s):  
Kelly A. Fox ◽  
Brandon Massoni ◽  
Matthew I. Campbell
Keyword(s):  
3D Printing ◽  
High Impact ◽  
Von Mises Stress ◽  
Manufacturing Cost ◽  
Cost Models ◽  
Part Geometry ◽  
Computer Aided ◽  
Solid Part ◽  
Metal 3D Printing ◽  
Von Mises

It is now common for computer-aided engineering tools to show a performance parameter — like von Mises stress — over the surface of a solid part. In this paper, a heatmap is generated for part cost where high values (shown in red) indicate regions with a high impact on manufacturing cost. This is accomplished by slicing the provided part many times in multiple orientations and evaluating the total costs of each side of the part at each slice. The costs from all the directions considered are combined to generate a heatmap to show how different regions affect cost, enabling the designer to make informed improvements to the part geometry. In this paper, our method for generating these heatmaps is presented with three primary manufacturing cost models: bar stock, forging, and metal 3D printing. In all cases, a machining operation is then applied to get to the final part shape. Results are shown to validate the approach and demonstrate its usefulness.

scholarly journals Fracture Resistance of Monolithic Zirconia Crowns in Implant Prostheses in Patients with Bruxism

Materials ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1623 ◽  
Author(s):  
Ting-Hsun Lan ◽  
Chin-Yun Pan ◽  
Pao-Hsin Liu ◽  
Mitch M. C. Chou
Keyword(s):  
Cyclic Loading ◽  
Computer Aided Design ◽  
Fracture Resistance ◽  
Testing Machine ◽  
Von Mises Stress ◽  
High Fracture ◽  
Computer Aided ◽  
Zirconia Crowns ◽  
Monolithic Zirconia ◽  
Von Mises

The aim of this study is to determine the minimum required thickness of a monolithic zirconia crown in the mandibular posterior area for patients with bruxism. Forty-nine full zirconia crowns, with seven different occlusal thicknesses of 0.4, 0.5, 0.6, 0.7, 0.8, 0.9, and 1.0 mm, were made by using a computer-aided design/computer-aided manufacturing system (CAD/CAM). Seven crowns in each group were subjected to cyclic loading at 800 N and 5 Hz in a servohydraulic testing machine until fracture or completion of 100,000 cycles. Seven finite element models comprising seven different occlusal thicknesses of 0.4, 0.5, 0.6, 0.7, 0.8, 0.9, and 1.0 mm were simulated using three different loads of vertical 800 N, oblique 10 degrees 800 N, and vertical 800 N + x N torque (x = 10, 50, and 100). The results of cyclic loading tests showed that the fracture resistance of the crown was positively associated with thickness. Specimen breakage differed significantly according to the different thicknesses of the prostheses (p < 0.01). Lowest von Mises stress values were determined for prostheses with a minimal thickness of 1.0 mm in different loading directions and with different forces. Zirconia specimens of 1.0 mm thickness had the lowest stress values and high fracture resistance and under 800 N of loading.

scholarly journals Aerodynamic and Structural Characteristics of a Centrifugal Compressor Impeller

2019 ◽  
Vol 9 (16) ◽  
pp. 3416 ◽  
Author(s):  
T R Jebieshia ◽  
Senthil Kumar Raman ◽  
Heuy Dong Kim
Keyword(s):  
Centrifugal Compressor ◽  
Structural Characteristics ◽  
Pressure Ratio ◽  
Operating Conditions ◽  
Von Mises Stress ◽  
Impeller Blade ◽  
Compressor Impeller ◽  
The One ◽  
Von Mises ◽  
Von Mises Stresses

The present study focuses on the aerodynamic performance and structural analysis of the centrifugal compressor impeller. The performance characteristics of the impeller are analyzed with and without splitter blades by varying the total number of main and splitter blades. The operating conditions of the compressor under centrifugal force and pressure load from the aerodynamic analysis are applied to the impeller blade and hub to perform the one-way Fluid–Structure Interaction (FSI). For the stress assessment, maximum equivalent von Mises stresses in the impeller blades are compared with the maximum allowable stress of the impeller material. The effects of varying the pressure field on the deformation and stress of the impeller are also calculated. The aerodynamic and structural performance of the centrifugal compressor at 73,000 rpm are investigated in terms of the efficiency, pressure ratio, equivalent von Mises stress, and total deformation of the impeller.

Plasto-Elastohydrodynamic Lubrication in Point Contacts for Surfaces With Three-Dimensional Sinusoidal Waviness and Real Machined Roughness

2014 ◽  
Vol 136 (3) ◽  
Author(s):  
Tao He ◽  
Ning Ren ◽  
Dong Zhu ◽  
Jiaxu Wang
Keyword(s):  
Plastic Deformation ◽  
Rough Surface ◽  
Mechanical Design ◽  
Three Dimensional ◽  
Elastohydrodynamic Lubrication ◽  
Operating Conditions ◽  
Von Mises Stress ◽  
Asperity Contacts ◽  
Lubrication Characteristics ◽  
Von Mises

Efficiency and durability are among the top concerns in mechanical design to minimize environmental impact and conserve natural resources while fulfilling performance requirements. Today mechanical systems are more compact, lightweight, and transmit more power than ever before, which imposes great challenges to designers. Under the circumstances, some simplified analyses may no longer be satisfactory, and in-depth studies on mixed lubrication characteristics, taking into account the effects of 3D surface roughness and possible plastic deformation, are certainly needed. In this paper, the recently developed plasto-elastohydrodynamic lubrication (PEHL) model is employed, and numerous cases with both sinusoidal waviness and real machined roughness are analyzed. It is observed that plastic deformation may occur due to localized high pressure peaks caused by the rough surface asperity contacts, even though the external load is still considerably below the critical load determined at the onset of plastic deformation in the corresponding smooth surface contact. It is also found, based on a series of cases analyzed, that the roughness height, wavelength, material hardening property, and operating conditions may all have significant influences on the PEHL performance, subsurface von Mises stress field, residual stresses, and plastic strains. Generally, the presence of plastic deformation may significantly reduce some of the pressure spikes and peak values of subsurface stresses and make the load support more evenly distributed among all the rough surface asperities in contact.

scholarly journals Numerical Analysis of the Crack Inspections Using Hybrid Approach for the Application the Circular Cantilever Rods

2021 ◽  
Vol 29 (2) ◽  
Author(s):  
Saddam Hussein Raheemah ◽  
Kareem Idan Fadheel ◽  
Qais Hussein Hassan ◽  
Ashham Mohammed Aned ◽  
Alaa Abdulazeez Turki Al-Taie ◽  
...  
Keyword(s):  
Structural Design ◽  
Hybrid Approach ◽  
Von Mises Stress ◽  
Whole Body ◽  
Total Deformation ◽  
Motion Equations ◽  
Maximum Deformation ◽  
Simulation Process ◽  
Maximum Value ◽  
Von Mises

The present study aims to investigate crack presence in a rigid steel beam so that it can be considered in structural design. A finite element method (FEM) had been used with the Ansys 16.1 software to simulate the whole steel body with three different forces and moments with a magnitude force subjected at the free end of the beam. The steel rod had been considered as simple cantilever to be modelled by the software. Von Mises stress had been considered in the simulation process where the maximum value of stress due to applied load and moment was 1.9 MPa. Total deformation of the whole body had also been considered to instigate the maximum deformation (4.3mm) due to applied loads and moments. Furthermore, MATLAB and through fuzzy logic had been used to assist in the investigation of cracks. Both approaches had been governed by the Euler-Bernoulli theory for free vibration of motion equations. The other aim of this study is to evaluate results received from the Ansys with MATLAB for the same boundary conditions as the case.

Sign in / Sign up

Export Citation Format

Share Document