scholarly journals Automatic Error Compensation for Free-Form Surfaces by Using On-Machine Measurement Data

2019 ◽  
Vol 9 (15) ◽  
pp. 3073 ◽  
Author(s):  
Wei-chen Lee ◽  
Yu-tzu Lee ◽  
Ching-Chih Wei
Keyword(s):  
Error Compensation ◽  
Tool Path ◽  
Substantial Reduction ◽  
Measurement Data ◽  
Compensation Method ◽  
Numerical Control ◽  
Free Form ◽  
Machining Errors ◽  
Free Form Surfaces ◽  
Finishing Machining

Currently, most computer numerical control (CNC) controllers lack the function needed to compensate machining errors for free-form surfaces. The objective of this research was to enhance the accuracy and precision of the machined free-form surfaces of a workpiece using the mirror compensation method with the on-measurement data. By mirroring the points measured after semi-finishing, a new free-form surface for finishing machining can be automatically reconstructed. The surface can then be used to generate the cutting tool path to reduce the errors during finishing machining. In this research, three different types of surfaces were used for evaluating the proposed method. The results show that the proposed method reduced the standard deviations of the three surface geometries by 61%, 61%, and 32%, respectively. We also evaluated the tool radius modification method commonly used in the industry for error compensation and found that there is no substantial reduction on standard deviation. Therefore, the effectiveness of the error compensation method proposed in this research is evident.

Error correction technique for numerical control machine tools based on the simplex method

2021 ◽  
pp. 095440542110281
Author(s):  
Hongwei Liu ◽  
Rui Yang ◽  
Pingjiang Wang ◽  
Jihong Chen ◽  
Hua Xiang
Keyword(s):  
Machine Tool ◽  
Error Compensation ◽  
Simplex Method ◽  
Tool Path ◽  
Repeated Measurements ◽  
Numerical Control ◽  
Machining Accuracy ◽  
Correction Technique ◽  
Fluctuation Range ◽  
Nc Machine

The objective of this research is to develop a novel correction mechanism to reduce the fluctuation range of tools in numerical control (NC) machining. Error compensation is an effective method to improve the machining accuracy of a machine tool. If the difference between two adjacent compensation data is too large, the fluctuation range of the tool will increase, which will seriously affect the surface quality of the machined parts in mechanical machining. The methodology used in compensation data processing is a simplex method of linear programming. This method reduces the fluctuation range of the tool and optimizes the tool path. The important aspect of software error compensation is to modify the initial compensation data by using an iterative method, and then the corrected tool path data are converted into actual compensated NC codes by using a postprocessor, which is implemented on the compensation module to ensure a smooth running path of the tool. The generated, calibrated, and amended NC codes were immediately fed to the machine tool controller. This technique was verified by using repeated measurements. The results of the experiments demonstrate efficient compensation and significant improvement in the machining accuracy of the NC machine tool.

Application of Convex Hull for Tool Interference Avoidance in 5-Axis CNC Machining

1996 ◽  
Author(s):  
Yuan-Shin Lee ◽  
Tien-Chien Chang
Keyword(s):  
Convex Hull ◽  
Tool Path ◽  
Correction Method ◽  
Nc Machining ◽  
Cnc Machining ◽  
Free Form ◽  
Interference Avoidance ◽  
Tool Interference ◽  
Free Form Surface ◽  
Free Form Surfaces

Abstract In this paper, a methodology of applying convex hull property in solving the tool interference problem is presented for 5-axis NC machining of free-form surfaces. Instead of exhausted point-by-point checking for possible tool interference, a quick checking can be done by using the convex hull constructed from the control polygon of free-form surface modeling. Global tool interference in 5-axis NC machining is detected using the convex hull of the free-form surface. A correction method for removing tool interference has also been developed to generate correct tool path for 5-axis NC machining. The inter-surface tool interference can be avoided by using the developed technique.

scholarly journals A Non-Delay Error Compensation Method for Dual-Driving Gantry-Type Machine Tool

Processes ◽  
2020 ◽  
Vol 8 (7) ◽  
pp. 748
Author(s):  
Qi Liu ◽  
Hong Lu ◽  
Xinbao Zhang ◽  
Yu Qiao ◽  
Qian Cheng ◽  
...  
Keyword(s):  
Machine Tool ◽  
Error Compensation ◽  
Prediction Method ◽  
Compensation Method ◽  
Industrial Robots ◽  
Numerical Control ◽  
Heavy Duty ◽  
Positioning Errors ◽  
Compensation Methods ◽  
Type Machine

The drive at the center of gravity (DCG) principle has been adopted in computer numerical control (CNC) machines and industrial robots that require heavy-duty and quick feeds. Using this principle requires accurate corrections of positioning errors. Conventional error compensation methods may cause vibrations and unstable control performances due to the delay between compensation and motor motion. This paper proposes a new method to reduce the positioning errors of the dual-driving gantry-type machine tool (DDGTMT), namely, a typical DCG-principle-based machine tool. An error prediction method is proposed to characterize errors online. An algorithm is proposed to quickly and accurately compensate the errors of the DDGTMT. Experiment results verify that the non-delay error compensation method proposed in this paper can effectively improve the accuracy of the DDGTMT.

scholarly journals Iso-level tool path planning for free-form surfaces

2014 ◽  
Vol 53 ◽  
pp. 117-125 ◽  
Author(s):  
Qiang Zou ◽  
Juyong Zhang ◽  
Bailin Deng ◽  
Jibin Zhao
Keyword(s):  
Path Planning ◽  
Tool Path ◽  
Free Form ◽  
Tool Path Planning ◽  
Free Form Surfaces

Table-Based Volumetric Error Compensation of Large Five-Axis Machine Tools

2016 ◽  
Vol 139 (2) ◽  
Author(s):  
Jennifer Creamer ◽  
Patrick M. Sammons ◽  
Douglas A. Bristow ◽  
Robert G. Landers ◽  
Philip L. Freeman ◽  
...  
Keyword(s):  
Machine Tool ◽  
Error Compensation ◽  
Machine Tools ◽  
Data Gathering ◽  
Measurement Data ◽  
Geometric Error ◽  
Compensation Method ◽  
Geometric Errors ◽  
Simultaneous Generation ◽  
Five Axis

This paper presents a geometric error compensation method for large five-axis machine tools. Compared to smaller machine tools, the longer axis travels and bigger structures of a large machine tool make them more susceptible to complicated, position-dependent geometric errors. The compensation method presented in this paper uses tool tip measurements recorded throughout the axis space to construct an explicit model of a machine tool's geometric errors from which a corresponding set of compensation tables are constructed. The measurements are taken using a laser tracker, permitting rapid error data gathering at most locations in the axis space. Two position-dependent geometric error models are considered in this paper. The first model utilizes a six degree-of-freedom kinematic error description at each axis. The second model is motivated by the structure of table compensation solutions and describes geometric errors as small perturbations to the axis commands. The parameters of both models are identified from the measurement data using a maximum likelihood estimator. Compensation tables are generated by projecting the error model onto the compensation space created by the compensation tables available in the machine tool controller. The first model provides a more intuitive accounting of simple geometric errors than the second; however, it also increases the complexity of projecting the errors onto compensation tables. Experimental results on a commercial five-axis machine tool are presented and analyzed. Despite significant differences in the machine tool error descriptions, both methods produce similar results, within the repeatability of the machine tool. Reasons for this result are discussed. Analysis of the models and compensation tables reveals significant complicated, and unexpected kinematic behavior in the experimental machine tool. A particular strength of the proposed methodology is the simultaneous generation of a complete set of compensation tables that accurately captures complicated kinematic errors independent of whether they arise from expected and unexpected sources.

scholarly journals Evaluating the Roughness According to the Tool Path Strategy When Milling Free Form Surfaces for Mold Application

Procedia CIRP ◽  
2014 ◽  
Vol 14 ◽  
pp. 188-193 ◽  
Author(s):  
Adriano Fagali de Souza ◽  
Adriane Machado ◽  
Sueli Fischer Beckert ◽  
Anselmo Eduardo Diniz
Keyword(s):  
Tool Path ◽  
Free Form ◽  
Free Form Surfaces

Surface Quality Prediction in Case of Steep Free Form Surface Milling

2016 ◽  
Vol 686 ◽  
pp. 119-124 ◽  
Author(s):  
Balázs Mikó
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Tool Path ◽  
Complex Geometry ◽  
Cutting Parameters ◽  
Free Form ◽  
Milling Cutter ◽  
Good Surface ◽  
2.5D Milling ◽  
Free Form Surfaces

The machining of free form surfaces is a current and important issue in die and mould industry. Beside the complex geometry, an accurate and productive machining and good surface quality are needed. The finishing milling carried out by a ball-end or toroid milling cutter defines the surface quality, which is characterized by the surface roughness and the tool path trace. The surface quality is defined by the properties of the milling cutter, the type of surface and its position, as well as the cutting parameters. This article focuses on the z-level milling of steep surfaces by 2.5D milling strategy. The importance of the different elements of the tool path is presented, the effect of cutting parameters is investigated, and a formula to predict the surface roughness is suggested.

Adaptive iso-planar tool path generation for machining of free-form surfaces

2003 ◽  
Vol 35 (2) ◽  
pp. 141-153 ◽  
Author(s):  
S. Ding ◽  
M.A. Mannan ◽  
A.N. Poo ◽  
D.C.H. Yang ◽  
Z. Han
Keyword(s):  
Tool Path ◽  
Tool Path Generation ◽  
Free Form ◽  
Path Generation ◽  
Free Form Surfaces

Tool Path Generation Method for High-Quality Machining of Free-Form Surfaces

2020 ◽  
Author(s):  
Yuki Takanashi ◽  
Hideki Aoyama
Keyword(s):  
Tool Path ◽  
High Accuracy ◽  
Tool Path Generation ◽  
Free Form ◽  
Machining Accuracy ◽  
Path Generation ◽  
High Quality ◽  
Nc Program ◽  
Free Form Surface ◽  
Free Form Surfaces

Abstract Machining data (NC program) is generated by a CAM system, which generates the tool path from the target shape as a plane approximation surface instead of a free-form surface. Owing to this plane approximation, machining accuracy is reduced. In this paper, we propose a method to process the shape with high accuracy by defining the areas where accuracy is not required as a plane approximation surface and defining the part where accuracy is required as free-form surfaces.

Sign in / Sign up

Export Citation Format

Share Document