scholarly journals Numerical Study of Heat Transfer Enhancement for Laminar Nanofluids Flow

2018 ◽  
Vol 8 (12) ◽  
pp. 2661 ◽  
Author(s):  
Ramon Ramirez-Tijerina ◽  
Carlos Rivera-Solorio ◽  
Jogender Singh ◽  
K. Nigam
Keyword(s):  
Heat Transfer ◽  
Single Phase ◽  
Volume Fraction ◽  
Numerical Study ◽  
Dispersion Model ◽  
Constant Heat Flux ◽  
Process Conditions ◽  
Straight Tube ◽  
Wide Range ◽  
Laminar Forced Convection

The laminar forced convection has been investigated for the flow of nanofluids in conventional straight tube (L = 5.34 m, dt = 10 mm) and straight microtube (L = 0.3 m, dt = 0.5 mm) under the constant temperature and constant heat flux conditions, separately. A wide range of the process parameters has been studied by varying three different type of base fluids including water, ethylene glycol and turbine oil with five different type of nanoparticles viz. Al2O3, TiO2, CuO, SiO2 and ZnO. Six different combinations of the geometries, base fluids and nanoparticle concentrations are considered in the present study. In addition to the single-phase model (SPH), the single-phase dispersion model (SPD) has been also used for effectiveness of the computed results. The results showed that Nusselt number (Nu) increases with increase in Reynolds number (Re). Further, the Nu considerably enhanced (up to 16% at volume fraction ϕ b = 4%, Re = 950) with increase in nanoparticle concentrations. Heat transfer correlations are developed for the flow of nanofluids in conventional straight tube and straight microtube over a wide range of process conditions (25 < Re < 1500, 0 < ϕ b < 10, 6 < Pr < 500) to enable a large number of engineering applications.

scholarly journals Numerical Study of Laminar Forced Convection of Water/Al2o3 Nanofluid in an Annulus with Constant Wall Temperature

2013 ◽  
Vol 14 (1) ◽  
Author(s):  
Amin Kashani ◽  
Davood Jalali-vahid ◽  
Siamak Hossainpour
Keyword(s):  
Heat Transfer ◽  
Forced Convection ◽  
Volume Concentration ◽  
Volume Fraction ◽  
Numerical Study ◽  
Flow Behavior ◽  
Convective Heat Transfer Coefficient ◽  
Two Phase ◽  
Constant Wall Temperature ◽  
Laminar Forced Convection

Laminar forced convection of a nanofluid consisting of water and Al2O3 in a horizontal annulus has been studied numerically. Two-phase mixture model has been used to investigate thermal behaviors of the nanofluid over constant temperature thermal boundary condition and with different volume concentration of nanoparticles. Comparisons with previously published experimental and analytical works on flow behavior in horizontal annulus show good agreements between the results as volume fraction is zero. In general convective heat transfer coefficient increases with nanoparticle concentration. ABSTRAK: Kertaskerja ini mengkaji secara numerik olakan paksa bendalir lamina yang menganduangi air dan Al2O3 didalam anulus mendatar. Model campuran dua fasa digunakan bagi mengkaji tingkah laku haba bendalir nano pada keadaan suhu malar dengan kepekatan nanopartikel berbeza. Perbandingan dengan karya eksperimen dan analitikal yang telah diterbitkan menunjukkan bahawa kelakuan aliran didalm anulus mendatar adalah baik apabila pecahan isipadu adalah sifar. Pada amnya, pekali pemindahan haba olakan meningkat dengan kepekatan nanopartikel. KEYWORDS: nanofluid; volume concentration; heat transfer enhancement; laminar flow convection; annulus

Numerical Simulation of Taylor Flow in Micro Circular Tubes

2015 ◽  
Author(s):  
Jingzhi Zhang ◽  
Wei Li
Keyword(s):  
Heat Transfer ◽  
Liquid Film ◽  
Single Phase ◽  
Volume Fraction ◽  
Flow Characteristics ◽  
Constant Heat Flux ◽  
Bulk Temperature ◽  
Capillary Tubes ◽  
Taylor Flow ◽  
Gas Volume

Heat transfer and flow characteristics of Taylor flow in micro capillary tubes have been investigated numerically with the Volume of Fluid (VOF) method. A constant heat flux (32kwm−2) is adopted at the tube wall. All seven computational cases have the same Reynolds number (Re=280), Capillary number (Ca=0.006) and homogenous void fraction (β=0.51), while the inlet gas volume fraction varies from 0.2 to 0.8. The results indicate that liquid slug length (Ll), gas slug length (Lg) and cell length (Lc) vary with α, while liquid film thickness δ remains constant. The friction factor f of Taylor flow is higher than single phase flow. The simulation results agree well with the correlation proposed by Kreutzer et al.. The Local Nusselt number (Nux) gets its peak value at the liquid film region, where the temperature difference between wall temperature (Tw) and fluid bulk temperature (Tbx) is smallest. The average Nu (Nuav) is about 2.8 times of single phase. This means that Taylor bubble can enhance the heat transfer coefficient in micro capillary tubes.

scholarly journals Lid-Driven and Inclined Square Cavity Filled With a Nanofluid: Optimum Heat Transfer

2015 ◽  
Vol 5 (1) ◽  
Author(s):  
Abdelkader Boutra ◽  
Karim Ragui ◽  
Nabila Labsi ◽  
Youb Khaled Benkahla
Keyword(s):  
Heat Transfer ◽  
Volume Fraction ◽  
Numerical Study ◽  
Square Enclosure ◽  
Coupled Equations ◽  
Flow And Heat Transfer ◽  
Wide Range ◽  
Optimum Heat ◽  
Nanoparticles Volume Fraction ◽  
Volume Method

AbstractThis paper reports a numerical study on mixed convection within a square enclosure, filled with a mixture of water and Cu (or Ag) nanoparticles. It is assumed that the temperature difference driving the convection comes from the side moving walls, when both horizontal walls are kept insulated. In order to solve the general coupled equations, a code based on the finite volume method is used and it has been validated after comparison between the present results and those of the literature. To make clear the effect of the main parameters on fluid flow and heat transfer inside the enclosure, a wide range of the Richardson number, taken from 0.01 to 100, the nanoparticles volume fraction (0% to 10%), and the cavity inclination angle (0&#186; to 180&#186;) are investigated. The phenomenon is analyzed through streamlines and isotherm plots, with special attention to the Nusselt number.

Numerical Study on Mixed Convection and Entropy Generation of a Nanofluid in a Lid-Driven Square Enclosure

2015 ◽  
Vol 138 (1) ◽  
Author(s):  
R. K. Nayak ◽  
S. Bhattacharyya ◽  
I. Pop
Keyword(s):  
Heat Transfer ◽  
Mixed Convection ◽  
Entropy Generation ◽  
Volume Fraction ◽  
Numerical Study ◽  
Control Volume ◽  
Transport Equations ◽  
Bejan Number ◽  
Square Enclosure ◽  
Wide Range

A numerical investigation of mixed convection due to a copper–water nanofluid in an enclosure is presented. The mixed convection is governed by moving the upper lid of the enclosure and imposing a vertical temperature gradient. The transport equations for fluid and heat are modeled by using the Boussinesq approximation. A modified form of the control volume based SIMPLET algorithm is used for the solution of the transport equations. The fluid flow and heat transfer characteristics are studied for a wide range of Reynolds number and Grashof number so as to have the Richardson number greater or less than 1. The nanoparticle volume fraction is considered up to 20%. Heat flow patterns are analyzed through the energy flux vector. The rate of enhancement in heat transfer due to the addition of nanoparticles is analyzed. The entropy generation and Bejan number are evaluated to demonstrate the thermodynamic optimization of the mixed convection. We have obtained the enhancement rate in heat transfer and entropy generation in nanofluid for a wide range of parameter values.

scholarly journals Convective Heat Transfer of Al2O3 and CuO Nanofluids Using Various Mixtures of Water-Ethylene Glycol as Base Fluids

2017 ◽  
Vol 7 (2) ◽  
pp. 1496-1503
Author(s):  
K. Boukerma ◽  
M. Kadja
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Ethylene Glycol ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Thermal Performance ◽  
Volume Fraction ◽  
Numerical Study ◽  
Constant Heat Flux ◽  
Volume Fractions

In this work, a numerical study has been performed on the convective heat transfer of Al2O3/Water-Ethylene Glycol (EG) and CuO/(W-EG) nanofluids flowing through a circular tube with circumferentially non-uniform heating (constant heat flux) under the laminar flow condition. We focus on the study of the effect of EG-water mixtures as base fluids with mass concentration ranging from 0% up to 100% ethylene glycol on forced convection. The effect on the flow and the convective heat transfer behavior of nanoparticle types, their volume fractions (φ=1-5%) and Reynolds number are also investigated. The results obtained show that the highest values of the average heat transfer coefficient is observed between 40% and 50% of EG concentration. The average Nusselt number increases with the increase in EG concentration in the base fluid, and the increase in the Reynolds number and volume fraction. For concentrations of EG above 60%, and for all volume fractions, the increase of thermal performance of nanofluids became inversely proportional to the increase of Reynolds number. In addition, CuO/(W-EG) nanofluids show the best thermal performance compared with Al2O3/ (W-EG) nanofluids.

scholarly journals A Computational Study on the Role of Parameters for Identification of Thyroid Nodules by Infrared Images (and Comparison with Real Data)

Sensors ◽  
2021 ◽  
Vol 21 (13) ◽  
pp. 4459
Author(s):  
José R. González ◽  
Charbel Damião ◽  
Maira Moran ◽  
Cristina A. Pantaleão ◽  
Rubens A. Cruz ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Thyroid Nodules ◽  
Numerical Study ◽  
Computational Study ◽  
Internal Heat ◽  
Heat Transfer Process ◽  
The Body ◽  
Physical Parameters ◽  
Infrared Sensors ◽  
Wide Range

According to experts and medical literature, healthy thyroids and thyroids containing benign nodules tend to be less inflamed and less active than those with malignant nodules. It seems to be a consensus that malignant nodules have more blood veins and more blood circulation. This may be related to the maintenance of the nodule’s heat at a higher level compared with neighboring tissues. If the internal heat modifies the skin radiation, then it could be detected by infrared sensors. The goal of this work is the investigation of the factors that allow this detection, and the possible relation with any pattern referent to nodule malignancy. We aim to consider a wide range of factors, so a great number of numerical simulations of the heat transfer in the region under analysis, based on the Finite Element method, are performed to study the influence of each nodule and patient characteristics on the infrared sensor acquisition. To do so, the protocol for infrared thyroid examination used in our university’s hospital is simulated in the numerical study. This protocol presents two phases. In the first one, the body under observation is in steady state. In the second one, it is submitted to thermal stress (transient state). Both are simulated in order to verify if it is possible (by infrared sensors) to identify different behavior referent to malignant nodules. Moreover, when the simulation indicates possible important aspects, patients with and without similar characteristics are examined to confirm such influences. The results show that the tissues between skin and thyroid, as well as the nodule size, have an influence on superficial temperatures. Other thermal parameters of thyroid nodules show little influence on surface infrared emissions, for instance, those related to the vascularization of the nodule. All details of the physical parameters used in the simulations, characteristics of the real nodules and thermal examinations are publicly available, allowing these simulations to be compared with other types of heat transfer solutions and infrared examination protocols. Among the main contributions of this work, we highlight the simulation of the possible range of parameters, and definition of the simulation approach for mapping the used infrared protocol, promoting the investigation of a possible relation between the heat transfer process and the data obtained by infrared acquisitions.

Heat transfer characteristics of nanofluids from a sinusoidal corrugated cylinder placed in a square cavity

2021 ◽  
pp. 095440622110272
Author(s):  
Salaika Parvin ◽  
Nepal Chandra Roy ◽  
Litan Kumar Saha ◽  
Sadia Siddiqa
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Rayleigh Number ◽  
Aspect Ratio ◽  
Average Nusselt Number ◽  
Numerical Study ◽  
Heat Transfer Characteristics ◽  
Number Range ◽  
Transfer Characteristics ◽  
Wide Range

A numerical study is performed to investigate nanofluids' flow field and heat transfer characteristics between the domain bounded by a square and a wavy cylinder. The left and right walls of the cavity are at constant low temperature while its other adjacent walls are insulated. The convective phenomena take place due to the higher temperature of the inner corrugated surface. Super elliptic functions are used to transform the governing equations of the classical rectangular enclosure into a system of equations valid for concentric cylinders. The resulting equations are solved iteratively with the implicit finite difference method. Parametric results are presented in terms of streamlines, isotherms, local and average Nusselt numbers for a wide range of scaled parameters such as nanoparticles concentration, Rayleigh number, and aspect ratio. Several correlations have been deduced at the inner and outer surface of the cylinders for the average Nusselt number, which gives a good agreement when compared against the numerical results. The strength of the streamlines increases significantly due to an increase in the aspect ratio of the inner cylinder and the Rayleigh number. As the concentration of nanoparticles increases, the average Nusselt number at the internal and external cylinders becomes stronger. In addition, the average Nusselt number for the entire Rayleigh number range gets enhanced when plotted against the volume fraction of the nanofluid.

scholarly journals Conduction and convection heat transfer characteristics of water-based au nanofluids in a square cavity with differentially heated side walls subjected to constant temperatures

2014 ◽  
Vol 18 (suppl.1) ◽  
pp. 189-200 ◽  
Author(s):  
Primoz Ternik ◽  
Rebeka Rudolf
Keyword(s):  
Heat Transfer ◽  
Rayleigh Number ◽  
Base Fluid ◽  
Volume Fraction ◽  
Heat Transfer Characteristics ◽  
Square Cavity ◽  
Onset Of Convection ◽  
Transfer Characteristics ◽  
Wide Range ◽  
Water Based

The present work deals with the natural convection in a square cavity filled with the water-based Au nanofluid. The cavity is heated on the vertical and cooled from the adjacent wall, while the other two horizontal walls are adiabatic. The governing differential equations have been solved by the standard finite volume method and the hydrodynamic and thermal fields were coupled together using the Boussinesq approximation. The main objective of this study is to investigate the influence of the nanoparticles? volume fraction on the heat transfer characteristics of Au nanofluids at the given base fluid?s (i.e. water) Rayleigh number. Accurate results are presented over a wide range of the base fluid Rayleigh number and the volume fraction of Au nanoparticles. It is shown that adding nanoparticles in a base fluid delays the onset of convection. Contrary to what is argued by many authors, we show by numerical simulations that the use of nanofluids can reduce the heat transfer rate instead of increasing it.

Experimental and Numerical Study of Methanol-Water Mixture Single-Phase Heat Transfer in a Micro-Channel Heat Sink

2012 ◽  
Author(s):  
Chun K. Kwok ◽  
Matthew M. Asada ◽  
Jonathan R. Mita ◽  
Weilin Qu
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Heat Sink ◽  
Single Phase ◽  
Numerical Study ◽  
Pure Water ◽  
Molar Fraction ◽  
Water Mixture ◽  
Micro Channel ◽  
Numerical Predictions

This paper presents an experimental study of single-phase heat transfer characteristics of binary methanol-water mixtures in a micro-channel heat sink containing an array of 22 microchannels with 240μm × 630μm cross-section. Pure water, pure methanol, and five methanol-water mixtures with methanol molar fraction of 16%, 36%, 50%, 63% and 82% were tested. Key parametric trends were identified and discussed. The experimental study was complemented by a three-dimensional numerical simulation. Numerical predictions and experimental data are in good agreement with a mean absolute error (MAE) of 0.87%.

Heat Transfer and Crystallization Modeling during Compression Molding of Thermoplastic Composite Parts

2015 ◽  
Vol 651-653 ◽  
pp. 1507-1512 ◽  
Author(s):  
Jalal Faraj ◽  
Baptiste Pignon ◽  
Jean Luc Bailleul ◽  
Nicolas Boyard ◽  
Didier Delaunay ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Physical Properties ◽  
Volume Fraction ◽  
Thermoplastic Composite ◽  
Large Temperature ◽  
Process Conditions ◽  
Thermoplastic Resin ◽  
Whole Process ◽  
Low Viscosity ◽  
Thermo Physical Properties

We present in this paper, the coupling of heat transfer to the crystallization of composite in a closed mold. The composite is based on thermoplastic resin (low viscosity PA 66) with glass fiber (50% volume fraction). In order to realize this coupling, an accurate characterizationof thermo physical properties in process conditions, especially in the molten and solid state is needed. In addition, theidentification of the parameters of crystallization kinetics is required. Therefore, we present the methods that were used to study the thermo physical properties as the thermal conductivity, heat capacity and the specific volume. Moreover, the kinetic of crystallization was estimated over a large temperature range by using Flash DSC and classical DSC. In order to validate the measurements, the whole process was modeled by finite elements. The model includes the resolution of the strong coupling between the heat transfer and crystallization. Finally, the experimental and numerical results were compared.

Sign in / Sign up

Export Citation Format

Share Document