scholarly journals Enhanced Magnetoelectric Effect in Permendur/Pb(Zr0.52Ti0.48)O3 Laminated Magnetostrictive/Piezoelectric Composite

2015 ◽  
Vol 5 (3) ◽  
pp. 587-594 ◽  
Author(s):  
Yanmin Jia ◽  
Wenjing Zhou ◽  
Ke Ma ◽  
Yongsheng Liu
Keyword(s):  
Magnetoelectric Effect ◽  
Piezoelectric Composite

Magnetoelectric effect in hybrid composite material

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Rafal Mech
Keyword(s):  
Magnetic Field ◽  
Composite Material ◽  
Magnetoelectric Effect ◽  
Power Source ◽  
Fatigue Tests ◽  
Piezoelectric Composite ◽  
Electric Voltage ◽  
Content Type ◽  
Novel Material ◽  
New Material

PurposeInvestigations over new types of materials as a potential power source for different types of devices were raised dramatically in the last few years. It is connected especially with global needs and that most of the devices in our world need electricity to work. In this paper, an investigation on magnetoelectric effect in the magnetostrictive-piezoelectric composite material is presented.Design/methodology/approachAn author's research setup for investigation of magnetoelectric effect in the developed novel material was prepared. The new composite material was made of magnetostrictive particles of Terfenol-D and lead zirconium titanate (PZT) material.FindingsObtained results show that changes in an electric voltage output from the prepared material are highly dependent on the changes in external magnetic field. It was found out that rate of changes of magnetic field around composite material is one of the most important factors which has influence on the magnetoelectric effect. Taking into account the obtained results, it was proven that prepared hybrid material shows magnetoelectric effect in the case of work in alternating magnetic field.Originality/valueThis phenomenon might be used in a field of energy harvesting as potential power source for devices with low power consumption. Moreover, this new material gives an opportunity to be used as an additional gauge for determination of deformation or crack propagation in the samples during fatigue tests.

scholarly journals Improved magnetoelectric effect in magnetostrictive/piezoelectric composite with flux concentration effect for sensitive magnetic sensor

AIP Advances ◽  
2015 ◽  
Vol 5 (4) ◽  
pp. 047114 ◽  
Author(s):  
Hao Zhang ◽  
Caijiang Lu ◽  
Changbao Xu ◽  
Yingjie Xiao ◽  
Junguo Gui ◽  
...  
Keyword(s):  
Magnetoelectric Effect ◽  
Magnetic Sensor ◽  
Concentration Effect ◽  
Piezoelectric Composite ◽  
Flux Concentration

Determination of Charge Coefficient of Piezoelectric Films Using a Combined Finite Element Model and Dynamic Loading Technique

2020 ◽  
Vol 835 ◽  
pp. 229-242
Author(s):  
Oboso P. Bernard ◽  
Nagih M. Shaalan ◽  
Mohab Hossam ◽  
Mohsen A. Hassan
Keyword(s):  
Finite Element ◽  
Dynamic Loading ◽  
Material Properties ◽  
Accurate Determination ◽  
Substrate Material ◽  
Experimental Results ◽  
Piezoelectric Composite ◽  
Piezoelectric Film ◽  
Piezoelectric Charge

Accurate determination of piezoelectric properties such as piezoelectric charge coefficients (d33) is an essential step in the design process of sensors and actuators using piezoelectric effect. In this study, a cost-effective and accurate method based on dynamic loading technique was proposed to determine the piezoelectric charge coefficient d33. Finite element analysis (FEA) model was developed in order to estimate d33 and validate the obtained values with experimental results. The experiment was conducted on a piezoelectric disc with a known d33 value. The effect of measuring boundary conditions, substrate material properties and specimen geometry on measured d33 value were conducted. The experimental results reveal that the determined d33 coefficient by this technique is accurate as it falls within the manufactures tolerance specifications of PZT-5A piezoelectric film d33. Further, obtained simulation results on fibre reinforced and particle reinforced piezoelectric composite were found to be similar to those that have been obtained using more advanced techniques. FE-results showed that the measured d33 coefficients depend on measuring boundary condition, piezoelectric film thickness, and substrate material properties. This method was proved to be suitable for determination of d33 coefficient effectively for piezoelectric samples of any arbitrary geometry without compromising on the accuracy of measured d33.

scholarly journals A Piezoelectric Wave-Energy Converter Equipped with a Geared-Linkage-Based Frequency Up-Conversion Mechanism

Sensors ◽  
2020 ◽  
Vol 21 (1) ◽  
pp. 204
Author(s):  
Shao-En Chen ◽  
Ray-Yeng Yang ◽  
Guang-Kai Wu ◽  
Chia-Che Wu
Keyword(s):  
Power Generation ◽  
Wave Energy ◽  
Wave Motion ◽  
Wave Energy Converter ◽  
Gear Train ◽  
Piezoelectric Composite ◽  
Maximum Height ◽  
Resistive Load ◽  
Linkage Mechanism ◽  
Energy Converter

In this paper, a piezoelectric wave-energy converter (PWEC), consisting of a buoy, a frequency up-conversion mechanism, and a piezoelectric power-generator component, is developed. The frequency up-conversion mechanism consists of a gear train and geared-linkage mechanism, which converted lower frequencies of wave motion into higher frequencies of mechanical motion. The slider had a six-period displacement compared to the wave motion and was used to excite the piezoelectric power-generation component. Therefore, the operating frequency of the piezoelectric power-generation component was six times the frequency of the wave motion. The developed, flexible piezoelectric composite films of the generator component were used to generate electrical voltage. The piezoelectric film was composed of a copper/nickel foil as the substrate, lead–zirconium–titanium (PZT) material as the piezoelectric layer, and silver material as an upper-electrode layer. The sol-gel process was used to fabricate the PZT layer. The developed PWEC was tested in the wave flume at the Tainan Hydraulics Laboratory, Taiwan (THL). The maximum height and the minimum period were set to 100 mm and 1 s, respectively. The maximum voltage of the measured value was 2.8 V. The root-mean-square (RMS) voltage was 824 mV, which was measured through connection to an external 495 kΩ resistive load. The average electric power was 1.37 μW.

Sign in / Sign up

Export Citation Format

Share Document