scholarly journals Metal Titanate (ATiO3, A: Ni, Co, Mg, Zn) Nanorods for Toluene Photooxidation under LED Illumination

2021 ◽  
Vol 11 (22) ◽  
pp. 10850
Author(s):  
Anna P. Souri ◽  
Natalia Andrigiannaki ◽  
Marilena Moschogiannaki ◽  
Vasiliki Faka ◽  
George Kiriakidis ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Ethylene Glycol ◽  
Separation Efficiency ◽  
Heterogeneous Photocatalysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Vis Spectroscopy ◽  
Ft Ir ◽  
Toluene Photooxidation

The increasing air pollution taking place in virtue of human activity has a novel impact in our health. Heterogeneous photocatalysis is a promising way of degrading volatile organic compounds (VOCs) that makes the quest of new and improved photocatalysts of great importance. Herein, perovskite-related materials ATiO3 with A = Mg, Ni, Co, Zn were synthesized through an ethylene glycol-mediated root, with ethylene glycol being used as a solvent and ligand. Characterization techniques such as X-ray diffraction (XRD), scanning electron microscopy, and energy dispersive X-ray spectroscopy (SEM/EDX), transmission electron microscopy (TEM), UV-vis spectroscopy, Raman spectroscopy, Fourier transform infrared (FT-IR), and photoluminescence spectroscopy (PL) were used in order to confirm the structure, the nanorod morphology, their absorption in UV-vis, and the separation efficiency of photogenerated charge carriers. The highest photoactivity was observed for ZnTiO3 in which 62% of toluene was decomposed after 60 min under LED illumination (54 mW/cm2).

Facile Synthesis of Phase Tunable MoO3 Nanostructures and Their Electrochemical Sensing Properties

2020 ◽  
Vol 20 (5) ◽  
pp. 2823-2831
Author(s):  
S. Muthamizh ◽  
C. Sengottaiyan ◽  
R. Jayavel ◽  
V. Narayanan
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Electrochemical Sensing ◽  
X Ray Diffraction ◽  
Facile Synthesis ◽  
X Ray ◽  
Solid State Decomposition ◽  
Transmission Electron ◽  
Vis Spectroscopy ◽  
Ft Ir

MoO3 nanostructures with tunable phases such as α-MoO3, β-MoO3 and their mixed phases were synthesized via a simple solid state decomposition method and employed as electrocatalyst for the detection of biomolecule. The phase and crystal structure of the synthesized MoO3 nanostructures were confirmed through X-ray diffraction (XRD) studies. The MoO3 nanostructures were also characterized by Fourier transform infrared spectroscopy (FT-IR), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), and UV-Vis spectroscopy for their structural, chemical state and optical properties, respectively. The observed results confirmed the successful formation of phase tunable MoO3 nanostructures. The surface texture and morphology of the samples was characterized by field emission scanning electron microscopy (FE-SEM) and transmission electron microscopy (TEM). The obtained images showed the formation of hexagons, cubes and rods morphology of MoO3. The synthesized MoO3 nanostructures were used to modify the surface of glassy carbon electrode (GCE) to detect biomolecule (quercetin).

scholarly journals Hydrothermal Synthesis, Characterization and Exploration of Photocatalytic Activities of Polyoxometalate: Ni-CoWO4 Nanoparticles

Crystals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 456
Author(s):  
Fahad A. Alharthi ◽  
Hamdah S. Alanazi ◽  
Amjad Abdullah Alsyahi ◽  
Naushad Ahmad
Keyword(s):  
Electron Microscopy ◽  
Hydrothermal Synthesis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Structure Morphology ◽  
Photocatalytic Activities ◽  
Ft Ir ◽  
Photocatalytic Reactions ◽  
Cobalt Tungstate

This study demonstrated the hydrothermal synthesis of bimetallic nickel-cobalt tungstate nanostructures, Ni-CoWO4 (NCW-NPs), and their phase structure, morphology, porosity, and optical properties were examined using X-ray Diffraction (XRD), Fourier-transform infrared spectroscopy (FT-IR), Scanning electron microscopy- energy dispersive X-ray spectroscopy (SEM-EDS), high resolution Transmission electron microscopy (HR-TEM), Brunauer-Emmett-Teller (BET) and Raman instruments. It was found that as-calcined NCW-NPs have a monoclinic phase with crystal size ~50–60 nm and is mesoporous. It possessed smooth, spherical, and cubic shape microstructures with defined fringe distance (~0.342 nm). The photocatalytic degradation of methylene blue (MB) and rose bengal (RB) dye in the presence of NCW-NPs was evaluated, and about 49.85% of MB in 150 min and 92.28% of RB in 90 min degraded under visible light. In addition, based on the scavenger’s study, the mechanism for photocatalytic reactions is proposed.

Effect of Synthesis Temperature on Particles Size and Morphology of Zirconium Oxide Nanoparticle

2017 ◽  
Vol 50 ◽  
pp. 18-31 ◽  
Author(s):  
Rudzani Sigwadi ◽  
Simon Dhlamini ◽  
Touhami Mokrani ◽  
Patrick Nonjola
Keyword(s):  
Electron Microscopy ◽  
Particle Size ◽  
Zirconium Oxide ◽  
Thermo Gravimetric Analysis ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Crystallite Sizes ◽  
Ft Ir

The paper presents the synthesis and investigation of zirconium oxide (ZrO2) nanoparticles that were synthesised by precipitation method with the effects of the temperatures of reaction on the particles size, morphology, crystallite sizes and stability at high temperature. The reaction temperature effect on the particle size, morphology, crystallite sizes and stabilized a higher temperature (tetragonal and cubic) phases was studied. Thermal decomposition, band structure and functional groups were analyzed by Brunauer-Emmett-Teller (BET), Scanning Electron Microscopy (SEM), Transmission electron microscopy (TEM), X-ray diffraction (XRD), Thermo-gravimetric analysis (TGA) and Fourier transform infrared (FT-IR). The crystal structure was determined using X-ray diffraction. The morphology and the particle size were studied using (SEM) and (TEM). The shaped particles were confirmed through the SEM analysis. The transmission electron microscopic analysis confirmed the formation of the nanoparticles with the particle size. The FT-IR spectra showed the strong presence of ZrO2 nanoparticles.

scholarly journals Microwave-assisted preparation of ZnS and ZnSe nanocrystals with different morphologies for photodegradation process of organic dyes

2019 ◽  
Author(s):  
Katarzyna Matras-Postolek ◽  
A. Zaba ◽  
S. Sovinska ◽  
D. Bogdal
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Organic Dyes ◽  
Zinc Sulphide ◽  
Conventional Heating ◽  
Bet Surface Area ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Vis Spectroscopy

Zinc sulphide (ZnS) and zinc selenide (ZnSe) and manganese-doped and un-doped with different morphologies from 1D do 3D microflowers were successfully fabricated in only a few minutes by solvothermal reactions under microwave irradiation. In order to compare the effect of microwave heating on the properties of obtained  nanocrystals, additionally the synthesis under conventional heating was conducted additionally in similar conditions. The obtained nanocrystals were systematically characterized in terms of structural and optical properties using X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), diffuse reflectance UV-Vis spectroscopy (DR UV-Vis), Fourier-transform infrared spectroscopy (FT-IR), photoluminescence spectroscopy (PL), X-ray photoelectron spectroscopy (XPS) and Brunauer-Emmett-Teller (BET) surface area analysis. The photocatalytic activity of ZnSe, ZnS, ZnS:Mn and ZnSe:Mn nanocrystals with different morphologies was evaluated by the degradation of methyl orange (MO) and Rhodamine 6G (R6G), respectively. The results show that Mn doped NCs samples had higher coefficient of degradation of organic dyes under ultraviolet irradiation (UV).

Synthesis of Indole Derivatives Using Biosynthesized ZnO-CaO Nanoparticles as an Efficient Catalyst

2021 ◽  
Vol 66 ◽  
pp. 61-71
Author(s):  
Tahereh Heidarzadeh ◽  
Navabeh Nami ◽  
Daryoush Zareyee
Keyword(s):  
Electron Microscopy ◽  
Indole Derivatives ◽  
X Ray Diffraction ◽  
Efficient Catalyst ◽  
X Ray ◽  
Transmission Electron ◽  
Solvent Free Conditions ◽  
Ft Ir ◽  
Eggshell Waste ◽  
Aromatic And Aliphatic Amines

The principal aim of this research is using biosynthesized ZnO-CaO nanoparticles (NPs) for preparation of indole derivatives. ZnO-CaO NPs have been prepared using Zn(CH3COO)2 and eggshell waste powder in solvent-free conditions. Morphology and structure of NPs were determined by FT-IR, X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), and energy dispersive spectra (EDS). It was used as a highly efficient catalyst for the synthesis of indole derivatives. Some indole derivatives were synthesized by the reaction of indole, formaldehyde, aromatic and aliphatic amines in the presence of ZnO-CaO NPs (5 mol%) in ethanol under reflux conditions. The assigned structure was further established by CHN analyses, NMR, and FT-IR spectra. Because of excellent capacity, the exceedingly simple workup and good yield, eco-friendly catalyst ZnO-CaO NPs were proved to be a good catalyst for this reaction.

Facile synthesis of water-soluble graphene-based composite: Non-covalently functionalized with chitosan-ionic liquid conjugation

2016 ◽  
Vol 09 (03) ◽  
pp. 1650045 ◽  
Author(s):  
Pei-Ying Li ◽  
Kai-Yu Cheng ◽  
Xiu-Cheng Zheng ◽  
Pu Liu ◽  
Xiu-Juan Xu
Keyword(s):  
Electron Microscopy ◽  
Ionic Liquid ◽  
Chemical Reduction ◽  
Water Soluble ◽  
X Ray Diffraction ◽  
Facile Synthesis ◽  
X Ray ◽  
Transmission Electron ◽  
Vis Spectroscopy ◽  
Text Interaction

Chitosan-ionic liquid conjugation (CILC), which was prepared through the reaction of 1-(4-bromobutyl)-3-methylimidazolium bromide (BBMIB) with chitosan, was firstly used to prepare functionalized graphene composite via the chemical reduction of graphene oxide (GO). The obtained water soluble graphene-based composite was characterized by transmission electron microscopy (TEM), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), ultraviolet-visible (UV–Vis) spectroscopy and so on. CILC-RGO showed excellent dispersion stability in water at the concentration of 2.0 mg/mL, which was stable for several months without any precipitate. This may be ascribed to the electrostatic attraction and [Formula: see text]–[Formula: see text] interaction between CILC and graphene.

Synthesis and Characterization of HgSe Nanostructure Using a Novel Precursor

2013 ◽  
Vol 32 (2) ◽  
pp. 157-162 ◽  
Author(s):  
Mahdiyeh Esmaeili-Zare ◽  
Masoud Salavati-Niasari ◽  
Davood Ghanbari
Keyword(s):  
Electron Microscopy ◽  
Synthesis And Characterization ◽  
Sonochemical Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Mercury Selenide ◽  
Ft Ir ◽  
Ft Ir Spectroscopy

AbstractMercury selenide nanostructures were synthesized from the reaction of N, N′-bis(salicylidene)propane-1,3-diamine mercury complex, (Hg(Salpn)) as a novel precursor, via sonochemical method. The effect of different surfactant on the morphology and particle size of the products was investigated. Products were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared (FT-IR) spectroscopy and X-ray energy dispersive spectroscopy (EDS).

scholarly journals Isolation and Characterization of Cellulose Nanofibers fromGigantochloa scortechiniias a Reinforcement Material

2016 ◽  
Vol 2016 ◽  
pp. 1-8 ◽  
Author(s):  
Chaturbhuj K. Saurabh ◽  
Asniza Mustapha ◽  
M. Mohd. Masri ◽  
A. F. Owolabi ◽  
M. I. Syakir ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Cellulose Nanofibers ◽  
X Ray Diffraction ◽  
X Ray ◽  
Isolation And Characterization ◽  
Transmission Electron ◽  
Reinforcement Material ◽  
Bamboo Fibers ◽  
Ft Ir

Cellulose nanofibers (CNF) were isolated fromGigantochloa scortechiniibamboo fibers using sulphuric acid hydrolysis. This method was compared with pulping and bleaching process for bamboo fiber. Scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectroscopy, X-ray diffraction, and thermogravimetric analysis were used to determine the properties of CNF. Structural analysis by FT-IR showed that lignin and hemicelluloses were effectively removed from pulp, bleached fibers, and CNF. It was found that CNF exhibited uniform and smooth morphological structures, with fiber diameter ranges from 5 to 10 nm. The percentage of crystallinity was significantly increased from raw fibers to cellulose nanofibers, microfibrillated, along with significant improvement in thermal stability. Further, obtained CNF were used as reinforcement material in epoxy based nanocomposites where tensile strength, flexural strength, and modulus of nanocomposites improved with the addition of CNF loading concentration ranges from 0 to 0.7%.

Optical and Structural Properties of PVP/Bi2S3 Nanoparticles by Chemical Method

2013 ◽  
Vol 678 ◽  
pp. 248-252
Author(s):  
K. Kavi Rasu ◽  
Dhandapani Vishnushankar ◽  
V. Veeravazhuthi
Keyword(s):  
Electron Microscopy ◽  
Diffraction Spectrum ◽  
X Ray Diffraction ◽  
Sem Images ◽  
X Ray ◽  
Ir Studies ◽  
Transmission Electron ◽  
Ft Ir ◽  
Crystalline Nature ◽  
Uv Visible

Bismuth sulfide (Bi2S3) and Polyvinyl pyrrolidone (PVP) encapsulated Bi2S3 Nanoparticles are synthesized from aqueous solutions at room temperature. Synthesized samples are subjected to UV-Visible Spectroscopy, X-Ray Diffraction (XRD), Scanning electron microscopy (SEM), Energy Dispersive Analysis of X-ray (EDAX), Transmission Electron Microscopy (TEM) and FT-IR studies and their results are compared. X-ray diffraction spectrum reveals the crystalline nature of the synthesized samples. Grain size value of PVP/ Bi2S3 nanoparticles show a decrease when compared to Bi2S3 nanoparticles and this ensures the good encapsulant effect of PVP on Bi2S3 nanoparticles. SEM images show that all the particles in the synthesized sample are nearly equal in size. From the TEM image we conclude that the particle size lies between 30nm to 70nm. Finally the samples are subjected to EDAX studies for determining their composition.

Synthesis and Electrochemical Characterization of Nano-Graphite Oxide for Enzyme Free Detection of Cholesterol

2015 ◽  
Vol 1786 ◽  
pp. 57-63
Author(s):  
Vasuda Bhatia ◽  
Bhawana Singh ◽  
Vinod K. Jain
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Graphite Oxide ◽  
Linear Response ◽  
X Ray Diffraction ◽  
X Ray ◽  
Embedding Technique ◽  
Transmission Electron ◽  
Ft Ir

ABSTRACTNano-graphite oxide has been synthesized from graphite flakes using modified Hummer’s method. Fourier transform infrared (FT-IR) data, x-ray diffraction (XRD) and transmission electron microscopy (TEM) revealed functionalization of the synthesised nano-graphitic platelets with oxygenated bonds. Using thermal embedding technique for the fabrication of self-assembled films, electrodes of nano-graphite oxide have been fabricated for enzyme free detection of cholesterol electrochemically. The electrodes provided a linear response for the enzyme less detection in the range of 50mg/dl to 500mg/dl with a correlation coefficient, R, of 0.99784 and sensitivity of 1.0587 µA/mg.

Sign in / Sign up

Export Citation Format

Share Document