scholarly journals Sampling Rate Impact on Precise Point Positioning with a Low-Cost GNSS Receiver

2021 ◽  
Vol 11 (16) ◽  
pp. 7669
Author(s):  
Rosendo Romero-Andrade ◽  
Manuel E. Trejo-Soto ◽  
Jesús R. Vázquez-Ontiveros ◽  
Daniel Hernández-Andrade ◽  
Juan L. Cabanillas-Zavala
Keyword(s):  
Urban Areas ◽  
Precise Point Positioning ◽  
Low Cost ◽  
Sampling Rate ◽  
Static Mode ◽  
Gnss Receiver ◽  
High Sampling Rate ◽  
Gnss Receivers ◽  
Potential Alternative ◽  
Point Positioning

Nowadays, with the incursion of low-cost GNSS receivers with modern characteristics, it is common to investigate and apply new methodologies and solutions with different receivers of this nature. Based on this fact, the performance of the solution obtained from the low-cost GNSS receiver is evaluated compared to a geodetic grade GNSS receiver at different sampling frequencies for the PPP-static and PPP-kinematic modes. For this, the original RINEX observation files were analyzed and decimated into different sampling rates as 0.1, 0.2, 1, 5, 15 and 30 s with TEQC software. All RINEX files were submitted to the Canadian Spatial Reference System Precise Point Positioning (CSRS-PPP) online service for processing with static and kinematic modes. The PPP-derived coordinates from the low-cost GNSS receiver were compared with the geodetic receiver to evaluate the obtained solution. The results reveal that the behavior of all studied sampling rates from the low-cost GNSS receiver are constant in achieved positioning. In addition, the achieved precision shows that it is recommendable to use a high sampling rate to obtain a cm level in PPP-static mode by using a low-cost GNSS receiver, this mode being the most accurate and potential alternative for structural health monitoring studies, mapping and positioning in urban areas.

scholarly journals Positioning Evaluation of Single and Dual-Frequency Low-Cost GNSS Receivers Signals Using PPP and Static Relative Methods in Urban Areas

2021 ◽  
Vol 11 (22) ◽  
pp. 10642
Author(s):  
Rosendo Romero-Andrade ◽  
Manuel E. Trejo-Soto ◽  
Alejandro Vega-Ayala ◽  
Daniel Hernández-Andrade ◽  
Jesús R. Vázquez-Ontiveros ◽  
...  
Keyword(s):  
Urban Areas ◽  
Precise Point Positioning ◽  
Low Cost ◽  
Observation Data ◽  
Dual Frequency ◽  
Positional Accuracy ◽  
Gnss Receivers ◽  
Point Positioning ◽  
Error Circle ◽  
Vertical Positioning

A positional accuracy obtained by the Precise Point Positioning and static relative methods was compared and analyzed. Test data was collected using low-cost GNSS receivers of single- and dual-frequency in urban areas. The data was analyzed for quality using the TEQC program to determine the degree of affectation of the signal in the urban area. Low-cost GNSS receivers were found to be sensitive to the multipath effect, which impacts positioning. The horizontal and vertical accuracy was evaluated with respect to Mexican regulations for the GNSS establishment criteria. Probable Error Circle (CEP) and Vertical Positioning Accuracy (EPV) were performed on low cost GNSS receiver observation data. The results show that low-cost dual-frequency GNSS receivers can be used in urban areas. The precision was obtained in the order of 0.013 m in the static relative method. The results obtained are comparable to a geodetic receiver in a geodetic baseline of <20 km. The study does not recommend using single and dual frequencies low cost GNSS receivers based on results obtained by the Precise Point Positioning (PPP) method in urban areas. The inclusion of the GGM10 model reduces the vertical precision obtained by using low cost GNSS receivers in both methods, conforming to the regulations only in the horizontal component.

scholarly journals Real-time GNSS precise point positioning for low-cost smart devices

GPS Solutions ◽  
2021 ◽  
Vol 25 (2) ◽  
Author(s):  
Liang Wang ◽  
Zishen Li ◽  
Ningbo Wang ◽  
Zhiyu Wang
Keyword(s):  
Carrier Phase ◽  
Measurement Errors ◽  
Precise Point Positioning ◽  
Low Cost ◽  
Smart Devices ◽  
Dual Frequency ◽  
Static Mode ◽  
Phase Measurements ◽  
Positioning Errors ◽  
Point Positioning

AbstractGlobal Navigation Satellite System raw measurements from Android smart devices make accurate positioning possible with advanced techniques, e.g., precise point positioning (PPP). To achieve the sub-meter-level positioning accuracy with low-cost smart devices, the PPP algorithm developed for geodetic receivers is adapted and an approach named Smart-PPP is proposed in this contribution. In Smart-PPP, the uncombined PPP model is applied for the unified processing of single- and dual-frequency measurements from tracked satellites. The receiver clock terms are parameterized independently for the code and carrier phase measurements of each tracking signal for handling the inconsistency between the code and carrier phases measured by smart devices. The ionospheric pseudo-observations are adopted to provide absolute constraints on the estimation of slant ionospheric delays and to strengthen the uncombined PPP model. A modified stochastic model is employed to weight code and carrier phase measurements by considering the high correlation between the measurement errors and the signal strengths for smart devices. Additionally, an application software based on the Android platform is developed for realizing Smart-PPP in smart devices. The positioning performance of Smart-PPP is validated in both static and kinematic cases. Results show that the positioning errors of Smart-PPP solutions can converge to below 1.0 m within a few minutes in static mode and the converged solutions can achieve an accuracy of about 0.2 m of root mean square (RMS) both for the east, north and up components. For the kinematic test, the RMS values of Smart-PPP positioning errors are 0.65, 0.54 and 1.09 m in the east, north and up components, respectively. Static and kinematic tests both show that the Smart-PPP solutions outperform the internal results provided by the experimental smart devices.

scholarly journals Enhanced Local Ionosphere Model for Multi-Constellations Single Frequency Precise Point Positioning Applications: Egyptian Case Study

2018 ◽  
Vol 53 (4) ◽  
pp. 141-157 ◽  
Author(s):  
Emad El Manaily ◽  
Mahmoud Abd Rabbou ◽  
Adel El-Shazly ◽  
Moustafa Baraka
Keyword(s):  
Precise Point Positioning ◽  
Sampling Rate ◽  
Single Frequency ◽  
Three Dimension ◽  
Static Mode ◽  
Ionosphere Model ◽  
Point Positioning ◽  
Limited Precision ◽  
Pass Through ◽  
Delay Correction

Abstract The positioning accuracy of single frequency precise point positioning (SFPPP) attributes mainly to the ionosphere error, which strongly affects GNSS signals. When GNSS signals pass through the various ionosphere layers, they will be bent and their speed will be changed due to dispersive nature of ionosphere. To correct the ionosphere error, it is common to use Klobuchar ionosphere model or Global Ionosphere Maps (GIM). However, Klobuchar can deal with only about 50% of the Ionosphere effect and global Ionosphere maps are often inadequate to describe detailed features of local ionosphere because of limited precision and resolution. In this paper, an enhanced local ionosphere model was developed relying on modeling of measurements from a dense Egyptian permanent tracking GNSS network in order to achieve high precision ionosphere delay correction. The performance of the developed enhanced Egyptian ionosphere model (EIM) was verified through multi-constellations SFPPP accuracy for static and kinematic modes. For static mode, 24 hours multi-constellations datasets collected at three selected stations, Alexandria, Cairo, and Aswan, in Egypt on February 27, 2017, to investigate the performance of the developed local ionospheric model in comparison with the Klobuchar, GIM and ionosphere free models. After session time of half an hour, the results show that the performance of static SFPPP based on the developed Egyptian ionospheric map (EIM) achieved a comparable accuracy WRT using ionosphere free model. While using EIM, achieved an improvements of (38%, 28%, and 42%) and (32%, 10%, and 37%) for accuracy of latitude, longitude, and altitude in comparison with using Klobuchar and GIM models, respectively For kinematic mode, datasets of 2 hours of observations with 1 second sampling rate were logged during vehicular test; the test was carried out on the ring road of the city of Cairo, Egypt, on September 16, 2017. After half an hour of kinematic SFPPP data-processing, the performance of using Egyptian ionospheric map (EIM) for ionosphere delay correction, achieved an improvements of three dimension coordinates of (83%, 47%, and 62%) and (57%, 65%, and 21%) with respect to using Klobuchar model and GIM model, respectively.

scholarly journals Evaluation of Quad-Constellation GNSS Precise Point Positioning in Egypt

2017 ◽  
Vol 52 (1) ◽  
pp. 9-18
Author(s):  
Emad El Manaily ◽  
Mahmoud Abd Rabbou ◽  
Adel El-Shazly ◽  
Moustafa Baraka
Keyword(s):  
Urban Areas ◽  
Precise Point Positioning ◽  
Low Cost ◽  
Single Point ◽  
Convergence Time ◽  
Reference Station ◽  
Single Frequency ◽  
Major Drawback ◽  
Positioning Accuracy ◽  
Point Positioning

Abstract Commonly, relative GPS positioning technique is used in Egypt for precise positioning applications. However, the requirement of a reference station is usually problematic for some applications as it limits the operational range of the system and increases the system cost and complexity On the other hand; the single point positioning is traditionally used for low accuracy applications such as land vehicle navigation with positioning accuracy up to 10 meters in some scenarios which caused navigation problems especially in downtown areas. Recently, high positioning accuracy can be obtained through Precise Point Positioning (PPP) technique in which only once GNSS receiver is used. However, the major drawback of PPP is the long convergence time to reach to the surveying grade accuracy compared to the existing relative techniques. Moreover, the PPP accuracy is significantly degraded due to shortage in satellite availability in urban areas. To overcome these limitations, the quad constellation GNSS systems namely; GPS.GLONASS, Galileo and BeiDou can be combined to increase the satellite availability and enhance the satellite geometry which in turn reduces the convergence time. In Egypt, at the moment, the signals of both Galileo and BeiDou could be logged with limited number of satellites up to four and six satellites for both Systems respectively. In this paper, we investigated the performance of the Quad-GNSS positioning in both dual- and single-frequency ionosphere free PPP modes for both high accurate and low cost navigation application, respectively. The performance of the developed PPP models will be investigated through GNSS data sets collected at three Egyptian cities namely, Cairo, Alexandria and Aswan.

Estimations of GNSS receiver internal delay using precise point positioning algorithm

2019 ◽  
Vol 13 (1) ◽  
pp. 41-46
Author(s):  
Natchapan Pothikunkupatarak ◽  
Thayathip Thongtan ◽  
Chalermchon Satirapod
Keyword(s):  
Precise Point Positioning ◽  
Frequency Standard ◽  
Propagation Path ◽  
Tropospheric Delay ◽  
Gps Receiver ◽  
Short Baseline ◽  
Gnss Receiver ◽  
Gnss Receivers ◽  
Point Positioning ◽  
Positioning Algorithm

Abstract Random and systematic errors affect navigation satellite observations on both pseudo-range and carrier phase. These errors are originated at satellites, propagation path and receivers. This study focuses on the GNSS receiver internal delay determination resulting from the receiver’s electronics circuit. The characterisation of the delay in the GNSS geodetic receivers is essential to enhance the accuracy for the time transfer and time comparisons as part of GNSS integrity chain determinations. The purpose of GNSS receiver internal delay at the National Institute of Metrology (Thailand), NIMT, is to estimate the characteristics and performances of the GNSS geodetic receiver used for international time comparisons. The experiments are simultaneously observed GNSS satellites by a GPS and a GNSS receivers and two separate antennas with short baseline (around 6 metres), where both receivers are connected to the identical external caesium frequency standard maintained as time and frequency standard of Thailand. The GPS receiver is well-defined for its receiver internal delay on the pseudo-range observation of C1, through comparisons using an internationally recognised method, while the geodetic GNSS receiver is to be defined on its receiver internal delay. These experiment observations started from 26 December 2017 to 17 January 2018 at NIMT, Pathumthani, Thailand. The determined unknowns are receiver position, receiver clock offset, tropospheric delay through the geodetic technique of static Precise Point Positioning observations with Bernese GNSS software version 5.2. Later the receiver internal delay of NIMT is computed and analysed. The receiver internal delay on GPS C1 code is successfully characterised, resulted as 346.0 nanoseconds as of this experiment.

scholarly journals Precise Point Positioning Using Dual-Frequency GNSS Observations on Smartphone

Sensors ◽  
2019 ◽  
Vol 19 (9) ◽  
pp. 2189 ◽  
Author(s):  
Qiong Wu ◽  
Mengfei Sun ◽  
Changjie Zhou ◽  
Peng Zhang
Keyword(s):  
Precise Point Positioning ◽  
Frequency Mode ◽  
Single Frequency ◽  
Dual Frequency ◽  
Static Mode ◽  
Position Errors ◽  
Point Positioning ◽  
Similar Accuracy ◽  
Positioning Algorithm ◽  
Gnss Observations

The update of the Android system and the emergence of the dual-frequency GNSS chips enable smartphones to acquire dual-frequency GNSS observations. In this paper, the GPS L1/L5 and Galileo E1/E5a dual-frequency PPP (precise point positioning) algorithm based on RTKLIB and GAMP was applied to analyze the positioning performance of the Xiaomi Mi 8 dual-frequency smartphone in static and kinematic modes. The results showed that in the static mode, the RMS position errors of the dual-frequency smartphone PPP solutions in the E, N, and U directions were 21.8 cm, 4.1 cm, and 11.0 cm, respectively, after convergence to 1 m within 102 min. The PPP of dual-frequency smartphone showed similar accuracy with geodetic receiver in single-frequency mode, while geodetic receiver in dual-frequency mode has higher accuracy. In the kinematic mode, the positioning track of the smartphone dual-frequency data had severe fluctuations, the positioning tracks derived from the smartphone and the geodetic receiver showed approximately difference of 3–5 m.

Single-Frequency Precise Point Positioning Using Multi-Constellation GNSS: GPS, GLONASS, Galileo and BeiDou

GEOMATICA ◽  
2016 ◽  
Vol 70 (2) ◽  
pp. 113-122 ◽  
Author(s):  
Mahmoud Abd Rabbou ◽  
Ahmed El-Rabbany
Keyword(s):  
Urban Areas ◽  
Precise Point Positioning ◽  
Cost Effective ◽  
Convergence Time ◽  
Single Frequency ◽  
Dual Frequency ◽  
Positioning Accuracy ◽  
Point Positioning ◽  
Beidou Satellites ◽  
Gnss Observations

Single-frequency precise point positioning (PPP) presents a cost-effective positioning technique for a large number of users. However, it possesses low positioning accuracy and convergence time compared with the dual-frequency PPP. Single-frequency PPP commonly employs GPS satellite systems that suffer from poor satellite geometry, especially in dense urban areas. We develop a new single-frequency PPP model that combines the observations of current GNSS constellations, including GPS, GLONASS, Galileo and Beidou. The MGEX IGS final precise products are utilized to account for the orbital and clock errors, while the IGS final global ionospheric maps (GIM) model is used to correct for the ionospheric delay. The GNSS inter-system biases are treated as additional unknowns in the estimation process. The con tri bution of the additional GNSS observations to single-frequency PPP is assessed through solution comparison with its traditional GPS-only counterpart. Various GNSS combinations are considered in the assessment, including GPS/GLONASS, GPS/Galileo, GPS/BeiDou and all-constellation GNSS. It is shown that the additional GNSS observations enhance the PPP solution accuracy and convergence time in comparison with the tra di tional GPS-only solution. Except for stations with a sufficient number of tracked BeiDou satellites, both Galileo and BeiDou have marginal effects on the positioning accuracy due to their limited number of satel lites. However, for stations with a sufficient number of visible BeiDou satellites, an average of 40% PPP accuracy improvement is obtained. The major contribution to the PPP accuracy enhancement is obtained from GLONASS satellite observations.

scholarly journals GNSS-Warp Software for Real-Time Precise Point Positioning

2015 ◽  
Vol 50 (2) ◽  
pp. 59-76 ◽  
Author(s):  
Hadaś Tomasz
Keyword(s):  
Real Time ◽  
Precise Point Positioning ◽  
Static Mode ◽  
Time Service ◽  
The Real ◽  
North East ◽  
Satellite Geometry ◽  
Point Positioning ◽  
Performance Validation ◽  
Mode A

Abstract On April 1, 2013 IGS launched the real-time service providing products for Precise Point Positioning (PPP). The availability of real-time makes PPP a very powerful technique to process GNSS signals in real-time and opens a new PPP applications opportunities. There are still, however, some limitations of PPP, especially in the kinematic mode. A significant change in satellite geometry is required to efficiently de-correlate troposphere delay, receiver clock offset, and receiver height. In order to challenge PPP limitations, the GNSS-WARP (Wroclaw Algorithms for Real-time Positioning) software has been developed from scratch at Wroclaw University of Environmental and Life Science in Poland. This paper presents the GNSS-WARP software itself and some results of GNSS data analysis using PPP and PPP-RTK (Real-Time Kinematic) technique. The results of static and kinematic processing in GPS only and GPS + GLONASS mode with final and real-time products are presented. Software performance validation in postprocessing mode confirmed that the software can be considered as a state-ofthe- art software and used for further studies on PPP algorithm development. The real-time positioning test made it possible to assess the quality of real-time coordinates, which is a few millimeters for North, East, Up in static mode, a below decimeter in kinematic mode. The accuracy and precision of height estimates in kinematic mode were improved by constraining the solution with an external, near real-time troposphere model. The software also allows estimation of real-time ZTD, however, the obtained precision of 11.2 mm means that further improvements in the software, real-time products or processing strategy are required.

Comparative analysis of precise point positioning processing technique with GPS low-cost in different technologies with academic software

Measurement ◽  
2019 ◽  
Vol 136 ◽  
pp. 337-344 ◽  
Author(s):  
Rosendo Romero-Andrade ◽  
Alejandra Zamora-Maciel ◽  
José de J. Uriarte-Adrián ◽  
Fréderiqué Pivot ◽  
Manuel E. Trejo-Soto
Keyword(s):  
Comparative Analysis ◽  
Precise Point Positioning ◽  
Low Cost ◽  
Processing Technique ◽  
Point Positioning
Sign in / Sign up

Export Citation Format

Share Document