scholarly journals Effect of Sunflower, Almond, and Rapeseed Oils as Additives on Thermal Properties of a Machinery Oil

2021 ◽  
Vol 11 (16) ◽  
pp. 7441
Author(s):  
José de Jesús Agustín Flores Cuautle ◽  
Oscar Osvaldo Sandoval González ◽  
Carlos Omar González Morán ◽  
José Pastor Rodríguez Jarquin ◽  
Citlalli Jessica Trujillo Romero ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Thermal Properties ◽  
Thermal Diffusivity ◽  
Vegetable Oils ◽  
Thermal Effusivity ◽  
Thermal Characterization ◽  
Tocopherol Content ◽  
Lubricating Oil ◽  
Wave Resonance ◽  
Resonance Cavity

Vegetable oils are considered to be eco-friendly and to offer good lubricant properties; however, their low thermo-oxidative stability makes their use as a lubricant base challenging. In this research, sunflower, almond, and rapeseed vegetable oils were added in volumes of 5, 10, 15, and 20% to a machinery oil, and the thermal properties of the resulting fluids were studied. Sunflower, almond, and rapeseed oils were chosen considering their fatty acid composition and the tocopherol content. During this investigation, thermal diffusivity was measured by using the thermal wave resonance cavity technique, while thermal effusivity was determined by the inverse photopyroelectric method, and the obtained values ranged from 4.63 to 5.75 Ws1/2m−2K−1 × 102. The thermal conductivity was calculated by obtaining a complete thermal characterization. The results showed a linear relationship between the percentage of vegetable oil and the thermal diffusivity. It was also noted that the thermal properties of diffusivity and effusivity could be tuned when using almond, sunflower, and rapeseed oils in the appropriate percentages. Hence, the influence of vegetable oils on the thermal properties of lubricating oil were closely related to the number of fatty acids.

scholarly journals Thermal Properties of Plaster Reinforced with Date Palm Fibers

2020 ◽  
Vol 16 (2) ◽  
pp. 259-266
Author(s):  
Mokhtar Rachedi ◽  
Abdelouahed Kriker
Keyword(s):  
Thermal Conductivity ◽  
Thermal Properties ◽  
Thermal Diffusivity ◽  
Specific Heat ◽  
Date Palm ◽  
Thermal Effusivity ◽  
Date Palm Fibers ◽  
Different Types ◽  
Local Materials ◽  
Significant Point

AbstractThis study aims both to investigate the thermal properties of plaster reinforced with date palm fibers and local natural resources valorization to batter using materials construction. For that, studying the effect of addition date palm fibers on the plaster's thermal properties is a significant point. In this work, we measured effective thermal conductivity, thermal diffusivity, specific heat, and thermal effusivity of date palm fibers reinforced plaster has been studied by CT meter. Samples configurations with four lengths (10 mm - 40 mm) and four-weight ratios (0.5 % - 2 %) of palm fibers in plaster. The results obtained demonstrate that an increase in the fraction of date palm fiber engenders to a significant decrease in the thermal conductivity, thermal diffusivity, and effusivity, even an increase for the specific heat of different types of samples. Finally, this study is a contribution to the valorization of local materials in southern Algeria, and results encourage the use of plaster and date palm fibers in the field of construction and go to eco-friendly buildings.

3D Examination of the Thermal Properties of Carbon-Carbon Composites

2014 ◽  
Author(s):  
Melanie Patrick ◽  
Messiha Saad
Keyword(s):  
Thermal Conductivity ◽  
Thermal Properties ◽  
High Temperature ◽  
Thermal Diffusivity ◽  
Specific Heat ◽  
Thermal Characterization ◽  
Flash Method ◽  
Carbon Composites ◽  
Scanning Calorimetry ◽  
Temperature Levels

Thermal characterization of composites is essential for their proper assignment to a specific application. Specific heat, thermal diffusivity, and thermal conductivity of carbon-carbon composites are essential in the engineering design process and in the analysis of aerospace vehicles, space systems and other high temperature thermal systems. Specifically, thermal conductivity determines the working temperature levels of a material and is influential in its performance in high temperature applications. There is insufficient thermal property data for carbon-carbon composites over a range of temperatures. The purpose of this research is to develop a thermal properties database for carbon-carbon composites that will contain in-plane (i-p) and through-the-thickness (t-t-t) thermal data at different temperatures as well as display the effects of graphitization on the composite material. The carbon-carbon composites tested were fabricated by the Resin Transfer Molding (RTM) technique, utilizing T300 2-D carbon fabric and Primaset PT-30 cyanate ester resin. Experimental methods were employed to measure the thermal properties. Following the ASTM standard E-1461, the flash method enabled the direct measurement of thermal diffusivity. Additionally, differential scanning calorimetry was performed in accordance with the ASTM E-1269 standard to measure the specific heat. The measured thermal diffusivity, specific heat, and density data were used to compute the thermal conductivity of the carbon-carbon composites. The measured through-the-thickness thermal conductivity values of all the materials tested range from 1.0 to 17 W/m·K, while in-plane values range from 3.8 to 4.6 W/m·K due to the effect of fiber orientation. Additionally, the graphitized samples exhibit a higher thermal conductivity because of the nature of the ordered graphite structure.

Thermal Characterization of Carbon-Carbon Composites

2011 ◽  
Author(s):  
Messiha Saad ◽  
Darryl Baker ◽  
Rhys Reaves
Keyword(s):  
Thermal Conductivity ◽  
Thermal Properties ◽  
Thermal Diffusivity ◽  
Specific Heat ◽  
Critical Role ◽  
Carbon Composite ◽  
Flash Method ◽  
Carbon Composites ◽  
Energy Storage Devices ◽  
Graphitized Carbon

Thermal properties of materials such as specific heat, thermal diffusivity, and thermal conductivity are very important in the engineering design process and analysis of aerospace vehicles as well as space systems. These properties are also important in power generation, transportation, and energy storage devices including fuel cells and solar cells. Thermal conductivity plays a critical role in the performance of materials in high temperature applications. Thermal conductivity is the property that determines the working temperature levels of the material, and it is an important parameter in problems involving heat transfer and thermal structures. The objective of this research is to develop thermal properties data base for carbon-carbon and graphitized carbon-carbon composite materials. The carbon-carbon composites tested were produced by the Resin Transfer Molding (RTM) process using T300 2-D carbon fabric and Primaset PT-30 cyanate ester. The graphitized carbon-carbon composite was heat treated to 2500°C. The flash method was used to measure the thermal diffusivity of the materials; this method is based on America Society for Testing and Materials, ASTM E1461 standard. In addition, the differential scanning calorimeter was used in accordance with the ASTM E1269 standard to determine the specific heat. The thermal conductivity was determined using the measured values of their thermal diffusivity, specific heat, and the density of the materials.

Experimental Study on Thermal Properties of Hollow Sphere Structures

2021 ◽  
Vol 407 ◽  
pp. 185-191
Author(s):  
Josef Tomas ◽  
Andreas Öchsner ◽  
Markus Merkel
Keyword(s):  
Thermal Conductivity ◽  
Experimental Study ◽  
Thermal Properties ◽  
Thermal Diffusivity ◽  
Specific Heat ◽  
Hollow Sphere ◽  
Plane Source ◽  
Source Method ◽  
Transient Plane Source ◽  
Transient Plane Source Method

Experimental analyses are performed to determine thermal conductivity, thermal diffusivity and volumetric specific heat with transient plane source method on hollow sphere structures. Single-sided testing is used on different samples and different surfaces. Results dependency on the surface is observed.

scholarly journals Application of sonication and freezing as initial treatments before microwave-vacuum drying of cranberries

2019 ◽  
Vol 2 (22) ◽  
pp. 151-167 ◽  
Author(s):  
Izabela Staniszewska ◽  
Szymon Staszyński ◽  
Magdalena Zielińska
Keyword(s):  
Thermal Conductivity ◽  
Thermal Properties ◽  
Thermal Diffusivity ◽  
Physical Properties ◽  
Color Change ◽  
Vacuum Drying ◽  
Drying Time ◽  
Dried Fruits ◽  
Microwave Vacuum Drying ◽  
Drying Kinetic

The aim of study was to determine the influence of sonication and freezing on the kinetic of the microwave-vacuum drying, energy consumption and physical properties of whole cranberries as well as evaluate the applicability of sonication instead of freezing in order to change their physical properties and the drying kinetic of whole cranberries. Microwave-vacuum drying of whole cranberries with/without initial treatments took from 12 ± 1 to 14.5 ± 0.5 minutes. All of treatments did not significantly shorten the drying time of cranberries. However, they increased SMER values even by 31%. Despite of cryogenic freezing, all of treatments significantly increased the values of Dew. Sonication combined with drying allowed to obtain dried berries characterized by the lowest cohesiveness (0.19±0.02), springiness (0.62±0.02) and chewiness (3.4±0.8 N), while cryogenic freezing combined with drying allowed to obtain dried fruits characterized by highest springiness (0.75±0.03) and low chewiness (3.3±0.5 N). The highest lightness (32.2±0.7), redness (32.6±0.8), and yellowness (11.1±0.7) were found for fruits subjected to initial convective freezing before drying. The efficiency of sonication in color change was comparable to cryogenic freezing and much lower than convective freezing. All of initial treatments increased such thermal properties of dried cranberries as thermal conductivity and thermal diffusivity.

Influence of Mesocarp Fibre Inclusion on Thermal Properties of Foamed Concrete

2021 ◽  
Vol 87 (1) ◽  
pp. 1-11
Author(s):  
Siti Shahirah Suhaili ◽  
Md Azree Othuman Mydin ◽  
Hanizam Awang
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Thermal Properties ◽  
Thermal Diffusivity ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Volume Fraction ◽  
Thermal Constant ◽  
Volume Fractions ◽  
Foamed Concrete

The addition of mesocarp fibre as a bio-composite material in foamed concrete can be well used in building components to provide energy efficiency in the buildings if the fibre could also offer excellent thermal properties to the foamed concrete. It has practical significance as making it a suitable material for building that can reduce heat gain through the envelope into the building thus improved the internal thermal comfort. Hence, the aim of the present study is to investigate the influence of different volume fractions of mesocarp fibre on thermal properties of foamed concrete. The mesocarp fibre was prepared with 10, 20, 30, 40, 50 and 60% by volume fraction and then incorporated into the 600, 1200 and 1800 kg/m3 density of foamed concrete with constant cement-sand ratio of 1:1.5 and water-cement ratio of 0.45. Hot disk thermal constant analyser was used to attain the thermal conductivity, thermal diffusivity and specific heat capacity of foamed concrete of various volume fractions and densities. From the experimental results, it had shown that addition of mesocarp fibre of 10-40% by volume fraction resulting in low thermal conductivity and specific heat capacity and high the thermal diffusivity of foamed concrete with 600 and 1800 kg/m3 density compared to the control mix while the optimum amount of mesocarp fibre only limit up to 30% by volume fraction for 1200 kg/m3 density compared to control mix. The results demonstrated a very high correlation between thermal conductivity, thermal diffusivity and specific heat capacity which R2 value more than 90%.

Thermal Properties of Thin Metallic Layer Deposited on Insulators: Effect of the Interface on the Independent Determination of the Thermal Diffusivity and Conductivity of the Layer

2008 ◽  
Author(s):  
Danie`le Fournier ◽  
Jean Paul Roger ◽  
Christian Fretigny
Keyword(s):  
Thermal Conductivity ◽  
Thermal Properties ◽  
Thermal Diffusivity ◽  
Thermal Resistance ◽  
Thermal Contact ◽  
Heat Diffusion ◽  
Metallic Layer ◽  
Good Thermal Contact ◽  
Lateral Heat

Lateral heat diffusion thermoreflectance is a very powerful tool for determining directly the thermal diffusivity of layered structures. To do that, experimental data are fitted with the help of a heat diffusion model in which the ratio between the thermal conductivity k and the thermal diffusivity D of each layer is fixed, and the thermal properties of the substrate are known. We have shown in a previous work that it is possible to determine independently the thermal diffusivity and the thermal conductivity of a metallic layer deposited on an insulator, by taking into consideration all the data obtained at different modulation frequencies. Moreover, it is well known that to prevent a lack of adhesion of a gold film deposited on substrates like silica, an intermediate very thin (Cr or Ti) layer is deposited to assure a good thermal contact. We extend our previous work: the asymptotic behaviour determination of the surface temperature wave at large distances from the modulated point heat source for one layer deposited on the substrate to the two layers model. In this case (very thin adhesion coating whose thermal properties and thickness are known), it can be establish that the thermal diffusivity and the thermal conductivity of the top layer can still be determined independently. It is interesting to underline that the calculus can also be extended to the case of a thermal contact resistance which has often to be taken into account between two solids. We call thermal resistance a very thin layer exhibiting a very low thermal conductivity. In this case, the three parameters we have to determine are the thermal conductivity and the thermal diffusivity of the layer and the thermal resistance. We will show that, in this case, the thermal conductivity of the layer is always obtained independently of a bound of the couple thermal resistance – thermal diffusivity, the thermal diffusivity being under bounded and the thermal resistance lower bounded. Experimental results on thin gold layers deposited on silica with and without adhesion layers are presented to illustrate the method. Discussions on the accuracy will also be presented.

Thermal Properties of Tungsten SRM’S 730 and 799

1978 ◽  
Vol 100 (2) ◽  
pp. 330-333 ◽  
Author(s):  
R. E. Taylor
Keyword(s):  
Thermal Conductivity ◽  
Electrical Resistivity ◽  
Thermal Properties ◽  
High Temperature ◽  
Thermal Diffusivity ◽  
Thermophysical Properties ◽  
Room Temperature ◽  
Standard Material ◽  
International Program ◽  
Sintered Tungsten

Samples of sintered and arc-cast tungsten are available from NBS as thermal conductivity (SRM 730) and electrical resistivity (SRM 799) standards for the temperature range from 4 to 3000K. NBS recommended values for these properties above room temperature are based on results of various researchers during a previous international program which included arc-cast and sintered tungsten. The sintered tungsten used in this program was found to be unsuited for use as a standard material due to inhomogeneity and high temperature instability. The present paper gives results at high temperatures for thermal conductivity, electrical resistivity, specific heat, thermal diffusivity and Wiedemann-Franz-Lorenz ratio for a sample of the NBS sintered tungsten using the Properties Research Laboratory’s multiproperty apparatus. These results are compared to values recommended by the Thermophysical Properties Research Center, NBS, and an international program.

STUDY OF THERMAL TRANSPORT PARAMETERS IN PbI2 SINGLE CRYSTAL USING A PHOTOACOUSTIC TECHNIQUE

2006 ◽  
Vol 20 (20) ◽  
pp. 1253-1260 ◽  
Author(s):  
D. S. AHLAWAT ◽  
D. MOHAN ◽  
S. K. GHOSHAL ◽  
R. D. SINGH ◽  
MEENAKSHI SHARMA
Keyword(s):  
Thermal Conductivity ◽  
Thermal Diffusivity ◽  
Single Crystal ◽  
Characteristic Frequency ◽  
Modulation Frequency ◽  
Thermal Effusivity ◽  
Photoacoustic Signal ◽  
Photoacoustic Technique ◽  
Front Side ◽  
Transport Parameters

The present work discusses the study of the transport properties of the PbI 2 single crystal using an indigenously developed photoacoutistic spectrometer. The amplitude photoacoustic signal, being a function of the modulation frequency of the incident optical beam, has been measured by using the front-side detection configuration. The characteristic frequency (fc) of the single crystal has been found to be 55 Hz. The values of thermal diffusivity, thermal conductivity and thermal effusivity in the case of PbI 2 have been derived experimentally. Their values have been compared with the values reported in a case which studied other materials in the literature. Thermal diffusion lengths have also been calculated at different chopping frequencies from 15 Hz to 90 Hz.

Sign in / Sign up

Export Citation Format

Share Document