scholarly journals Electromagnetic Simulations and Measurements of the K-800 Superconducting Cyclotron RF Cavity at INFN-LNS

2021 ◽  
Vol 11 (13) ◽  
pp. 5995
Author(s):  
Giuseppe Torrisi ◽  
Giorgio Sebastiano Mauro ◽  
Lorenzo Neri ◽  
Luciano Allegra ◽  
Antonio Caruso ◽  
...  
Keyword(s):  
Vacuum Chamber ◽  
Impedance Matching ◽  
Three Dimensional ◽  
Rf Cavity ◽  
Electromagnetic Simulations ◽  
Superconducting Cyclotron ◽  
Operating Frequency Range ◽  
Eigenmode Analysis ◽  
Proposed Modification ◽  
The Impact

In this paper, a complete three-dimensional (3D) RF model of the cyclotron coaxial resonator—including the coaxial sliding shorts, the “Liner” vacuum chamber, the coupler, the trimmer, and the high RF voltage “Dee” structures—has been developed. An eigenmode analysis was used to simulate the tuning of the resonator in the operating frequency range of 15–48 MHz obtained by two movable sliding shorts and a trimmer. A driven analysis has been performed in order to compute the |S11| parameter (or impedance matching) of the cavity excited by a movable coaxial power coupler. The numerical simulations have been performed using the different peculiarities of two commercial tools, COMSOL Multiphysics and CST microwave studio. Experimental validation of the developed model is presented. The evidence of an unwanted electric field component, orthogonal to the accelerating field, was discovered and a mitigation is also proposed. The impact of the proposed modification was evaluated by using a 3D beam dynamics code under development in the framework of the Superconducting Cyclotron upgrade ongoing at INFN-LNS.

A Novel Scheme for Wide Bandwidth Chip-to-Chip Communications

2007 ◽  
Vol 4 (1) ◽  
pp. 1-7 ◽  
Author(s):  
Qing Liu ◽  
Patrick Fay ◽  
Gary H. Bernstein
Keyword(s):  
Integrated Circuits ◽  
Coplanar Waveguide ◽  
Impedance Matching ◽  
Three Dimensional ◽  
Fabrication Process ◽  
Silicon Substrates ◽  
Electromagnetic Simulations ◽  
Communication Paradigm ◽  
On Chip ◽  
Test Chips

Quilt Packaging (QP), a novel chip-to-chip communication paradigm for system-in-package integration, is presented. By forming protruding metal nodules along the edges of the chips and interconnecting integrated circuits (ICs) through them, QP offers an approach to ameliorate the I/O speed bottleneck. A fabrication process that includes deep reactive ion etching, electroplating, and chemical-mechanical polishing is demonstrated. As a low-temperature process, it can be easily integrated into a standard IC fabrication process. Three-dimensional electromagnetic simulations of coplanar waveguide QP structures have been performed, and geometries intended to improve impedance matching at the interface between the on-chip interconnects and the chip-to-chip nodule structures were evaluated. Test chips with 100 μm wide nodules were fabricated on silicon substrates, and s-parameters of chip-to-chip interconnects were measured. The insertion loss of the chip-to-chip interconnects was as low as 0.2 dB at 40 GHz. Simulations of 20 μm wide QP structures suggest that the bandwidth of the inter-chip nodules is expected to be above 200 GHz.

scholarly journals The Development of Frequency Tripler Based on Six-Anode Schottky Varactors

Micromachines ◽  
2021 ◽  
Vol 12 (12) ◽  
pp. 1490
Author(s):  
Yuhang Li ◽  
Jin Meng ◽  
Dehai Zhang ◽  
Haotian Zhu
Keyword(s):  
Output Power ◽  
Impedance Matching ◽  
Three Dimensional ◽  
Input Power ◽  
Frequency Multiplier ◽  
Dimensional Structure ◽  
Basic Design ◽  
Peak Output Power ◽  
The Impact ◽  
Multiplier Circuit

The development of a millimeter-wave unbalanced frequency tripler based on the nonlinear characteristics of planar Schottky varactors is presented. The entire module is designed by hybrid integration. A frequency multiplier circuit model was established to reflect the influence of diode parameters and the impedance matching on the multiplier in different frequency bands. The effect of junction imbalance on the output power of the frequency multiplier was investigated and the multiplier was improved based on the basic design. The addition of a cut microstrip stub in the improved diode unit reduced the impact of a power imbalance on frequency multiplier performance. The characteristics of the multiplier circuit were analyzed by the full-wave electromagnetic simulation of the three-dimensional structure and the harmonic balance simulation of the circuit. Test results showed that the peak output power of the improved frequency tripler was 12.6 mW at 277 GHz with an input power of 200 mW, an effective 12% improvement over the basic design.

Design Optimization of Via Transitions for Broadband Applications

2003 ◽  
Author(s):  
Albert Chee W. Lu ◽  
Wei Fan ◽  
Lai L. Wai ◽  
Lin Jin ◽  
Lee A. Low
Keyword(s):  
Impedance Matching ◽  
Test Vehicle ◽  
Electromagnetic Simulations ◽  
Full Wave ◽  
Resonance Test ◽  
High Bandwidth ◽  
Optimization Methodology ◽  
Key Aspects ◽  
The Impact ◽  
Cavity Effect

This paper describes the two key aspects of via transition optimization methodology: impedance matching and power plane resonance suppression. Ground vias are used to improve the impedance mismatch caused by the via transition and the optimal location of the ground vias at the same time helps to suppress the resonance caused by the cavity effect of the power plane pair. Full-wave electromagnetic simulations were carried out to demonstrate that via transition optimization is able achieve resonance-free high bandwidth operation. Optimal use of ground vias will not only enhance impedance matching but also significantly suppress suppression due to power plane resonance. Test vehicle characterizations were also carried out to demonstrate the impact of ground vias and power plane resonance characteristics on signal integrity.

Analyzing the Impact of X-Ray Tomography on the Reliability of Integrated Circuits

2015 ◽  
Author(s):  
Halit Dogan ◽  
Md Mahbub Alam ◽  
Navid Asadizanjani ◽  
Sina Shahbazmohamadi ◽  
Domenic Forte ◽  
...  
Keyword(s):  
Integrated Circuits ◽  
Integrated Circuit ◽  
3D Imaging ◽  
Three Dimensional ◽  
Serial Sectioning ◽  
Promising Technique ◽  
Flash Memories ◽  
X Ray ◽  
3D Information ◽  
The Impact

Abstract X-ray tomography is a promising technique that can provide micron level, internal structure, and three dimensional (3D) information of an integrated circuit (IC) component without the need for serial sectioning or decapsulation. This is especially useful for counterfeit IC detection as demonstrated by recent work. Although the components remain physically intact during tomography, the effect of radiation on the electrical functionality is not yet fully investigated. In this paper we analyze the impact of X-ray tomography on the reliability of ICs with different fabrication technologies. We perform a 3D imaging using an advanced X-ray machine on Intel flash memories, Macronix flash memories, Xilinx Spartan 3 and Spartan 6 FPGAs. Electrical functionalities are then tested in a systematic procedure after each round of tomography to estimate the impact of X-ray on Flash erase time, read margin, and program operation, and the frequencies of ring oscillators in the FPGAs. A major finding is that erase times for flash memories of older technology are significantly degraded when exposed to tomography, eventually resulting in failure. However, the flash and Xilinx FPGAs of newer technologies seem less sensitive to tomography, as only minor degradations are observed. Further, we did not identify permanent failures for any chips in the time needed to perform tomography for counterfeit detection (approximately 2 hours).

scholarly journals Numerical simulation of the impact of an integrated renovation project on the Maowei Sea hydrodynamic environment

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Cui Wang ◽  
Ling Cai ◽  
Yaojian Wu ◽  
Yurong Ouyang
Keyword(s):  
Water Exchange ◽  
Land Reclamation ◽  
Three Dimensional ◽  
Exchange Capacity ◽  
Reclamation Project ◽  
Hydrodynamic Environment ◽  
Sea Area ◽  
Water Quality Models ◽  
The Impact ◽  
Main Factor

AbstractIntegrated renovation projects are important for marine ecological environment protection. Three-dimensional hydrodynamics and water quality models are developed for the Maowei Sea to assess the hydrodynamic environment base on the MIKE3 software with high resolution meshes. The results showed that the flow velocity changed minimally after the project, decreasing by approximately 0.12 m/s in the east of the Maowei Sea area and increasing by approximately 0.01 m/s in the northeast of the Shajing Port. The decrease in tidal prism (~ 2.66 × 106 m3) was attributed to land reclamation, and accounted for just 0.86% of the pre-project level. The water exchange half-life increased by approximately 1 day, implying a slightly reduced water exchange capacity. Siltation occurred mainly in the reclamation and dredging areas, amounting to back-silting of approximately 2 cm/year. Reclamation project is the main factor causing the decrease of tidal volume and weakening the hydrodynamics in Maowei Sea. Adaptive management is necessary for such a comprehensive regulation project. According to the result, we suggest that reclamation works should strictly prohibit and dredging schemes should optimize in the subsequent regulation works.

scholarly journals Mechanical Behavior of Hydroxyapatite-Chitosan Composite: Effect of Processing Parameters

Minerals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 213
Author(s):  
Hamid Ait Said ◽  
Hassan Noukrati ◽  
Hicham Ben Youcef ◽  
Ayoub Bayoussef ◽  
Hassane Oudadesse ◽  
...  
Keyword(s):  
Molecular Weight ◽  
Compressive Strength ◽  
Mechanical Strength ◽  
Bone Repair ◽  
Mechanical Stability ◽  
Three Dimensional ◽  
Processing Parameters ◽  
Composite Effect ◽  
Solid Liquid ◽  
The Impact

Three-dimensional hydroxyapatite-chitosan (HA-CS) composites were formulated via solid-liquid technic and freeze-drying. The prepared composites had an apatitic nature, which was demonstrated by X-ray diffraction and Infrared spectroscopy analyses. The impact of the solid/liquid (S/L) ratio and the content and the molecular weight of the polymer on the composite mechanical strength was investigated. An increase in the S/L ratio from 0.5 to 1 resulted in an increase in the compressive strength for HA-CSL (CS low molecular weight: CSL) from 0.08 ± 0.02 to 1.95 ± 0.39 MPa and from 0.3 ± 0.06 to 2.40 ± 0.51 MPa for the HA-CSM (CS medium molecular weight: CSM). Moreover, the increase in the amount (1 to 5 wt%) and the molecular weight of the polymer increased the mechanical strength of the composite. The highest compressive strength value (up to 2.40 ± 0.51 MPa) was obtained for HA-CSM (5 wt% of CS) formulated at an S/L of 1. The dissolution tests of the HA-CS composites confirmed their cohesion and mechanical stability in an aqueous solution. Both polymer and apatite are assumed to work together, giving the synergism needed to make effective cylindrical composites, and could serve as a promising candidate for bone repair in the orthopedic field.

scholarly journals Impact of inter-reader contouring variability on textural radiomics of colorectal liver metastases

2020 ◽  
Vol 4 (1) ◽  
Author(s):  
Francesco Rizzetto ◽  
Francesca Calderoni ◽  
Cristina De Mattia ◽  
Arianna Defeudis ◽  
Valentina Giannini ◽  
...  
Keyword(s):  
Liver Metastases ◽  
Hausdorff Distance ◽  
Intraclass Correlation ◽  
Three Dimensional ◽  
Liver Lesion ◽  
Dice Coefficient ◽  
Rf Values ◽  
Enhanced Computed Tomography ◽  
Relative Change ◽  
The Impact

Abstract Background Radiomics is expected to improve the management of metastatic colorectal cancer (CRC). We aimed at evaluating the impact of liver lesion contouring as a source of variability on radiomic features (RFs). Methods After Ethics Committee approval, 70 liver metastases in 17 CRC patients were segmented on contrast-enhanced computed tomography scans by two residents and checked by experienced radiologists. RFs from grey level co-occurrence and run length matrices were extracted from three-dimensional (3D) regions of interest (ROIs) and the largest two-dimensional (2D) ROIs. Inter-reader variability was evaluated with Dice coefficient and Hausdorff distance, whilst its impact on RFs was assessed using mean relative change (MRC) and intraclass correlation coefficient (ICC). For the main lesion of each patient, one reader also segmented a circular ROI on the same image used for the 2D ROI. Results The best inter-reader contouring agreement was observed for 2D ROIs according to both Dice coefficient (median 0.85, interquartile range 0.78–0.89) and Hausdorff distance (0.21 mm, 0.14–0.31 mm). Comparing RF values, MRC ranged 0–752% for 2D and 0–1567% for 3D. For 24/32 RFs (75%), MRC was lower for 2D than for 3D. An ICC > 0.90 was observed for more RFs for 2D (53%) than for 3D (34%). Only 2/32 RFs (6%) showed a variability between 2D and circular ROIs higher than inter-reader variability. Conclusions A 2D contouring approach may help mitigate overall inter-reader variability, albeit stable RFs can be extracted from both 3D and 2D segmentations of CRC liver metastases.

scholarly journals 3DIV update for 2021: a comprehensive resource of 3D genome and 3D cancer genome

2020 ◽  
Vol 49 (D1) ◽  
pp. D38-D46
Author(s):  
Kyukwang Kim ◽  
Insu Jang ◽  
Mooyoung Kim ◽  
Jinhyuk Choi ◽  
Min-Seo Kim ◽  
...  
Keyword(s):  
Cell Line ◽  
Large Scale ◽  
Three Dimensional ◽  
Cancer Cell Line ◽  
Cancer Genome ◽  
Structural Variations ◽  
3D Genome ◽  
Tightly Coupled ◽  
Regulatory Effects ◽  
The Impact

Abstract Three-dimensional (3D) genome organization is tightly coupled with gene regulation in various biological processes and diseases. In cancer, various types of large-scale genomic rearrangements can disrupt the 3D genome, leading to oncogenic gene expression. However, unraveling the pathogenicity of the 3D cancer genome remains a challenge since closer examinations have been greatly limited due to the lack of appropriate tools specialized for disorganized higher-order chromatin structure. Here, we updated a 3D-genome Interaction Viewer and database named 3DIV by uniformly processing ∼230 billion raw Hi-C reads to expand our contents to the 3D cancer genome. The updates of 3DIV are listed as follows: (i) the collection of 401 samples including 220 cancer cell line/tumor Hi-C data, 153 normal cell line/tissue Hi-C data, and 28 promoter capture Hi-C data, (ii) the live interactive manipulation of the 3D cancer genome to simulate the impact of structural variations and (iii) the reconstruction of Hi-C contact maps by user-defined chromosome order to investigate the 3D genome of the complex genomic rearrangement. In summary, the updated 3DIV will be the most comprehensive resource to explore the gene regulatory effects of both the normal and cancer 3D genome. ‘3DIV’ is freely available at http://3div.kr.

scholarly journals The effect of the outlet angle β2 on the thermomechanical behavior of a centrifugal compressor blade

2020 ◽  
Vol 29 (1) ◽  
pp. 1-8
Author(s):  
Ahmed Allali ◽  
Sadia Belbachir ◽  
Ahmed Alami ◽  
Belhadj Boucham ◽  
Abdelkader Lousdad
Keyword(s):  
Mechanical Behavior ◽  
Centrifugal Compressor ◽  
Three Dimensional ◽  
Complex Form ◽  
Compressor Blade ◽  
Stress Fields ◽  
The Finite Element Method ◽  
Mechanical Fatigue ◽  
Outlet Angle ◽  
The Impact

AbstractThe objective of this work lies in the three-dimensional study of the thermo mechanical behavior of a blade of a centrifugal compressor. Numerical modeling is performed on the computational code "ABAQUS" based on the finite element method. The aim is to study the impact of the change of types of blades, which are defined as a function of wheel output angle β2, on the stress fields and displacements coupled with the variation of the temperature.This coupling defines in a realistic way the thermo mechanical behavior of the blade where one can note the important concentrations of stresses and displacements in the different zones of its complex form as well as the effects at the edges. It will then be possible to prevent damage and cracks in the blades of the centrifugal compressor leading to its failure which can be caused by the thermal or mechanical fatigue of the material with which the wheel is manufactured.

scholarly journals A guideline for 3D printing terminology in biomedical research utilizing ISO/ASTM standards

2021 ◽  
Vol 7 (1) ◽  
Author(s):  
Amy E. Alexander ◽  
Nicole Wake ◽  
Leonid Chepelev ◽  
Philipp Brantner ◽  
Justin Ryan ◽  
...  
Keyword(s):  
3D Printing ◽  
Medical Literature ◽  
Three Dimensional ◽  
Physical Object ◽  
Medical Community ◽  
Layer By Layer ◽  
Digital File ◽  
Standardized Terminology ◽  
Standard Terms ◽  
The Impact

AbstractFirst patented in 1986, three-dimensional (3D) printing, also known as additive manufacturing or rapid prototyping, now encompasses a variety of distinct technology types where material is deposited, joined, or solidified layer by layer to create a physical object from a digital file. As 3D printing technologies continue to evolve, and as more manuscripts describing these technologies are published in the medical literature, it is imperative that standardized terminology for 3D printing is utilized. The purpose of this manuscript is to provide recommendations for standardized lexicons for 3D printing technologies described in the medical literature. For all 3D printing methods, standard general ISO/ASTM terms for 3D printing should be utilized. Additional, non-standard terms should be included to facilitate communication and reproducibility when the ISO/ASTM terms are insufficient in describing expository details. By aligning to these guidelines, the use of uniform terms for 3D printing and the associated technologies will lead to improved clarity and reproducibility of published work which will ultimately increase the impact of publications, facilitate quality improvement, and promote the dissemination and adoption of 3D printing in the medical community.

Sign in / Sign up

Export Citation Format

Share Document