scholarly journals Formulation, Validation, and Application of a Novel 3D BEM Tool for Vertical Axis Wind Turbines of General Shape and Size

2021 ◽  
Vol 11 (13) ◽  
pp. 5874
Author(s):  
Andrea G. Sanvito ◽  
Vincenzo Dossena ◽  
Giacomo Persico
Keyword(s):  
Wind Tunnel ◽  
Wind Turbines ◽  
Three Dimensional ◽  
Vertical Axis ◽  
Small Scale ◽  
Engineering Practice ◽  
Blade Profile ◽  
General Shape ◽  
Vertical Axis Wind Turbines ◽  
Shape And Size

Low order models based on the Blade Element Momentum (BEM) theory exhibit modeling issues in the performance prediction of Vertical Axis Wind Turbines (VAWT) compared to Computational Fluid Dynamics, despite the widespread engineering practice of such methods. The present study shows that the capability of BEM codes applied to VAWTs can be greatly improved by implementing a novel three-dimensional set of high-order corrections and demonstrates this by comparing the BEM predictions against wind-tunnel experiments conducted on three small-scale VAWT models featuring different rotor design (H-shaped and Troposkein), blade profile (NACA0021 and DU-06-W200), and Reynolds number (from 0.8×105 to 2.5×105). Though based on the conventional Double Multiple Stream Tube (DMST) model, the here-presented in-house BEM code incorporates several two-dimensional and three-dimensional corrections including: accurate extended polar data, flow curvature, dynamic stall, a spanwise-distributed formulation of the tip losses, a fully 3D approach in the modeling of rotors featuring general shape (such as but not only, the Troposkein one), and accounting for the passive effects of supporting struts and pole. The detailed comparison with experimental data of the same models, tested in the large-scale wind tunnel of the Politecnico di Milano, suggests the very good predictive capability of the code in terms of power exchange, torque coefficient, and loads, on both time-mean and time-resolved basis. The peculiar formulation of the code allows including in a straightforward way the usual spanwise non-uniformity of the incoming wind and the effects of skew, thus allowing predicting the turbine operation in a realistic open-field in presence of the environmental boundary layer. A systematic study on the operation of VAWTs in multiple environments, such as in coastal regions or off-shore, and highlighting the sensitivity of VAWT performance to blade profile selection, rotor shape and size, wind shear, and rotor tilt concludes the paper.

scholarly journals Wind Tunnel testing of small Vertical-Axis Wind Turbines in Turbulent Flows

2017 ◽  
Vol 199 ◽  
pp. 3176-3181 ◽  
Author(s):  
Andreu Carbó Molina ◽  
Gianni Bartoli ◽  
Tim de Troyer
Keyword(s):  
Wind Tunnel ◽  
Turbulent Flows ◽  
Wind Turbines ◽  
Vertical Axis ◽  
Wind Tunnel Testing ◽  
Vertical Axis Wind Turbines ◽  
Tunnel Testing

scholarly journals Characterization of a new open jet wind tunnel to optimize and test vertical axis wind turbines

2017 ◽  
Vol 9 (3) ◽  
pp. 033302 ◽  
Author(s):  
Silvana Tourn ◽  
Jordi Pallarès ◽  
Ildefonso Cuesta ◽  
Uwe Schmidt Paulsen
Keyword(s):  
Wind Tunnel ◽  
Wind Turbines ◽  
Vertical Axis ◽  
Vertical Axis Wind Turbines

Detailed Analysis of the Wake Structure of a Straight-Blade H-Darrieus Wind Turbine by Means of Wind Tunnel Experiments and Computational Fluid Dynamics Simulations

2017 ◽  
Vol 140 (3) ◽  
Author(s):  
Alessandro Bianchini ◽  
Francesco Balduzzi ◽  
Giovanni Ferrara ◽  
Lorenzo Ferrari ◽  
Giacomo Persico ◽  
...  
Keyword(s):  
Fluid Dynamics ◽  
Experimental Data ◽  
Computational Fluid Dynamics ◽  
Wind Tunnel ◽  
Wind Turbines ◽  
Large Scale ◽  
Vertical Axis ◽  
Performance Estimation ◽  
Small Scale ◽  
Dynamics Simulations

Darrieus vertical axis wind turbines (VAWTs) have been recently identified as the most promising solution for new types of applications, such as small-scale installations in complex terrains or offshore large floating platforms. To improve their efficiencies further and make them competitive with those of conventional horizontal axis wind turbines, a more in depth understanding of the physical phenomena that govern the aerodynamics past a rotating Darrieus turbine is needed. Within this context, computational fluid dynamics (CFD) can play a fundamental role, since it represents the only model able to provide a detailed and comprehensive representation of the flow. Due to the complexity of similar simulations, however, the possibility of having reliable and detailed experimental data to be used as validation test cases is pivotal to tune the numerical tools. In this study, a two-dimensional (2D) unsteady Reynolds-averaged Navier–Stokes (U-RANS) computational model was applied to analyze the wake characteristics on the midplane of a small-size H-shaped Darrieus VAWT. The turbine was tested in a large-scale, open-jet wind tunnel, including both performance and wake measurements. Thanks to the availability of such a unique set of experimental data, systematic comparisons between simulations and experiments were carried out for analyzing the structure of the wake and correlating the main macrostructures of the flow to the local aerodynamic features of the airfoils in cycloidal motion. In general, good agreement on the turbine performance estimation was constantly appreciated.

scholarly journals Numerical Investigations of the Effects of the Rotating Shaft and Optimization of Urban Vertical Axis Wind Turbines

Energies ◽  
2018 ◽  
Vol 11 (7) ◽  
pp. 1870 ◽  
Author(s):  
Lidong Zhang ◽  
Kaiqi Zhu ◽  
Junwei Zhong ◽  
Ling Zhang ◽  
Tieliu Jiang ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Suction Side ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Small Scale ◽  
Physical Parameters ◽  
Rotating Shaft ◽  
Vertical Axis Wind Turbines ◽  
Negative Effect

The central shaft is an important and indispensable part of a small scale urban vertical axis wind turbines (VAWTs). Normally, it is often operated at the same angular velocity as the wind turbine. The shedding vortices released by the rotating shaft have a negative effect on the blades passing the wake of the wind shaft. The objective of this study is to explore the influence of the wake of rotating shaft on the performance of the VAWT under different operational and physical parameters. The results show that when the ratio of the shaft diameter to the wind turbine diameter (α) is 9%, the power loss of the wind turbine in one revolution increases from 0% to 25% relative to that of no-shaft wind turbine (this is a numerical experiment for which the shaft of the VAWT is removed in order to study the interactions between the shaft and blade). When the downstream blades pass through the wake of the shaft, the pressure gradient of the suction side and pressure side is changed, and an adverse effect is also exerted on the lift generation in the blades. In addition, α = 5% is a critical value for the rotating shaft wind turbine (the lift-drag ratio trend of the shaft changes differently). In order to figure out the impacts of four factors; namely, tip speed ratios (TSRs), α, turbulence intensity (TI), and the relative surface roughness value (ks/ds) on the performance of a VAWT system, the Taguchi method is employed in this study. The influence strength order of these factors is featured by TSRs > ks/ds > α > TI. Furthermore, within the range we have analyzed in this study, the optimal power coefficient (Cp) occurred under the condition of TSR = 4, α = 5%, ks/ds = 1 × 10−2, and TI = 8%.

FloVAWT: Progress on the Development of a Coupled Model of Dynamics for Floating Offshore Vertical Axis Wind Turbines

2013 ◽  
Author(s):  
Maurizio Collu ◽  
Michael Borg ◽  
Andrew Shires ◽  
Feargal P. Brennan
Keyword(s):  
Experimental Data ◽  
Wind Turbines ◽  
Three Dimensional ◽  
Coupled Model ◽  
Vertical Axis ◽  
Potential Method ◽  
Vertical Axis Wind Turbine ◽  
Vertical Axis Wind Turbines ◽  
Wind Profiles ◽  
Gyroscopic Effects

In the present article, progress on the development of an aero-hydro-servo-elastic coupled model of dynamics for floating Vertical Axis Wind Turbines (VAWTs) is presented, called FloVAWT (Floating Vertical Axis Wind Turbine). Aerodynamics is based on Paraschivoiu’s Double-Multiple Streamtube (DMST) model [1] [2], relying on blade element momentum (BEM) theory, but also taking into account three-dimensional effects, dynamic stall, and unsteady wind profiles and platform motions. Hydrodynamics is modelled with a time domain seakeeping model [3], based on hydrodynamic coefficients estimated with a frequency analysis potential method. In this first phase of the research program, the system is considered a rigid body. The mooring system is represented through a user defined force-displacement relationship. Due to the lack of experimental data on offshore floating VAWTs, the model has initially been validated by taking each module separately and comparing it against known experimental data, showing good agreement. The capabilities of the program are illustrated through a case study, giving an insight on the relative importance of aerodynamics loads and gyroscopic effects with respect to hydrodynamic load effects.

Time-Resolved Experimental Characterization of the Wakes Shed by H-Shaped and Troposkien Vertical Axis Wind Turbines

2017 ◽  
Vol 139 (3) ◽  
Author(s):  
Giacomo Persico ◽  
Vincenzo Dossena ◽  
Berardo Paradiso ◽  
Lorenzo Battisti ◽  
Alessandra Brighenti ◽  
...  
Keyword(s):  
Wind Turbines ◽  
Large Scale ◽  
Three Dimensional ◽  
Vertical Axis ◽  
Speed Ratio ◽  
Local Dynamic ◽  
Performance Measurements ◽  
Time Resolved ◽  
Vertical Axis Wind Turbines ◽  
Blade Section

In this paper, the aerodynamics of two vertical axis wind turbines (VAWTs) are discussed, on the basis of a wide set of experiments performed at Politecnico di Milano, Milan, Italy. A H-shaped and a Troposkien Darrieus turbine for microgeneration, featuring the same swept area and blade section, are tested at full-scale. Performance measurements show that the Troposkien rotor outperforms the H-shaped turbine, thanks to the larger midspan section of the Troposkien rotor and to the nonaerodynamic struts of the H-shaped rotor. These features are consistent with the character of the wakes shed by the turbines, measured by means of hot wire anemometry on several surfaces downstream of the models. The H-shape and Troposkien turbine wakes exhibit relevant differences in the three-dimensional morphology and unsteady evolution. In particular, large-scale vortices dominate the tip region of the wake shed by the H-shape turbine; these vortices pulsate significantly during the period, due to the periodic fluctuation of the blade aerodynamic loading. Conversely, the highly tapered shape of the Troposkien rotor not only prevents the onset of tip vortices, but also induces a dramatic spanwise reduction of tip speed ratio (TSR), promoting the onset of local dynamic stall marked by high periodic and turbulent unsteadiness in the tip region of the wake. The way in which these mechanisms affect the wake evolution and mixing process for the two classes of turbines is investigated for different tip speed ratios, highlighting some relevant implications in the framework of wind energy exploitation.

scholarly journals Parked and Operating Loads Analysis in the Aerodynamic Design of Multi-megawatt-scale Floating Vertical Axis Wind Turbines

2021 ◽  
Author(s):  
Mohammad Sadman Sakib ◽  
D. Todd Griffith
Keyword(s):  
Aspect Ratio ◽  
Wind Turbines ◽  
Three Dimensional ◽  
Vertical Axis ◽  
Lateral Force ◽  
Aerodynamic Design ◽  
Power Performance ◽  
Vertical Axis Wind Turbines ◽  
Design Variables ◽  
Loads Analysis

Abstract. A good understanding of aerodynamic loading is essential in the design of vertical axis wind turbines (VAWTs) to properly capture design loads and to estimate the power production. This paper presents a comprehensive aerodynamic design study for a 5 MW Darrieus offshore VAWT in the context of multi-megawatt floating VAWTs. This study systematically analyzes the effect of different, important design variables including the number of blades (N), aspect ratio (AR) and blade tapering in a comprehensive loads analysis of both the parked and operating aerodynamic loads including turbine power performance analysis. Number of blades (N) is studied for 2- and 3-bladed turbines, aspect ratio is defined as ratio of rotor height (H) and rotor diameter (D) and studied for values from 0.5 to 1.5, and blade tapering is applied by means of adding solidity to the blades towards blade root ends, which affects aerodynamic and structural performance. Analyses were carried out using a three-dimensional vortex model named CACTUS (Code for Axial and Crossflow TUrbine Simulation) to evaluate both instantaneous azimuthal parameters as well as integral parameters, such as loads (thrust force, lateral force, and torque loading) and power. Parked loading is a major concern for VAWTs, thus this work presents a broad evaluation of parked loads for the design variables noted above. This study also illustrates that during the operation of a turbine, lateral loads are on par with thrust loads, which will significantly affect the structural sizing of rotor and platform & mooring components.

Sign in / Sign up

Export Citation Format

Share Document