scholarly journals A Procedure to Prepare Sand–Clay Mixture Samples for Soil–Structure Interface Direct Shear Tests

2021 ◽  
Vol 11 (12) ◽  
pp. 5337
Author(s):  
Kexin Yin ◽  
Jiangxin Liu ◽  
Andreea-Roxana Vasilescu ◽  
Eugenia Di Filippo ◽  
Khaoula Othmani
Keyword(s):  
Sample Preparation ◽  
Soil Structure ◽  
Preparation Procedure ◽  
Preparation Technique ◽  
Direct Shear ◽  
Test Results ◽  
Shear Tests ◽  
Kaolinite Clay ◽  
Direct Shear Tests ◽  
Sample Preparation Procedure

A large number of experimental studies on sand–clay mixtures are well documented in the literature; however, the preparation protocol is rarely clearly detailed or varies a lot according to the authors. Variations in the preparation technique obviously increases the challenge of comparing different test results. As a consequence, sample preparation for sand–clay mixtures should be kept as constant as possible to ensure homogeneity and uniformity of samples and limit result variability. This paper develops a detailed procedure on how to prepare sand–clay samples for interface direct shear tests. Sand–clay mixtures are prepared with Fontainebleau sand, kaolinite clay and distilled water by the S1 (sand–water–clay) protocol. The uniformity of the reconstituted specimens is assessed by measuring the water content and density on three slices from the top to the bottom across the specimens. The repeatability of the samples is checked with oedometer and interface direct shear tests. This sample preparation procedure can be used for preparing sand–clay mixture for interface direct shear tests to investigate the influence of clay content or other effects (e.g., temperature) on the mechanical behavior of soil–structure interface. It has demonstrated great performance in preparing samples with good homogeneity and shape, compared to other traditional reconstitution techniques. With the sample preparation procedure, we can obtain repeatable test results as well.

scholarly journals Comparison of Mechanical Properties of Fiber-Reinforced Sand under Triaxial Compression and Direct Shear

2015 ◽  
Vol 7 (1) ◽  
Author(s):  
Reza Noorzad ◽  
Seyed Taher Ghoreyshi Zarinkolaei
Keyword(s):  
Shear Strength ◽  
Axial Strain ◽  
Triaxial Compression ◽  
Polypropylene Fiber ◽  
Triaxial Tests ◽  
Direct Shear ◽  
Test Results ◽  
Peak Reduction ◽  
Shear Tests ◽  
Direct Shear Tests

AbstractThis research investigates the behavior of sand reinforced with polypropylene fiber. To do this, 40 direct shear tests and 40 triaxial tests were performed on the coastal beaches of Babolsar, a city in the North of Iran. The effect of parameters such as fiber content, length of fiber and normal or confining pressure on the behavior of Babolsar sand have been studied. In this study, four various fiber contents (0, 0.25, 0.5 and 1 percent), three different lengths of fiber (6, 12 and 18 mm) and four normal or confining pressures (50, 100, 200 and 400 kPa) have been employed. The test results show that fiber inclusion has a significant effect on the behavior of sand. In both direct shear and triaxial tests, the addition of fibers improved shear strength parameters (C, '), increased peak shear strength and axial strain at failure, and also limited the amount of post-peak reduction in shear resistance. The comparison of the test results revealed that due to better fiber orientation toward the direction of principal tensile strain in triaxial test as compared to direct shear tests, the fiber efficiency and its effect on soil behavior is much more significant in triaxial specimens.

Red Sandstone Aggregate Mixture Experimental Study of Dynamic Compaction High Fill Embankment

2014 ◽  
Vol 1065-1069 ◽  
pp. 696-701
Author(s):  
Zhao Jun Chen ◽  
Wen Li ◽  
Xiang Qu
Keyword(s):  
Experimental Study ◽  
Rayleigh Wave ◽  
Dynamic Compaction ◽  
Direct Shear ◽  
Test Results ◽  
Shear Tests ◽  
Red Sandstone ◽  
Direct Shear Tests ◽  
Water Intensity ◽  
Intensity Decay

Direct shear tests by laboratory to study the red sandstone aggregate mixture under the action of water intensity decay law, got red sandstone aggregate mixture, fill high subgrade compaction experimental study, tests showed that dynamic compaction compacted earth and rock mix fill embankment feasible, Rayleigh Wave test results show that the effect of dynamic compaction compaction good.

scholarly journals Shear strength behaviour of sand-bentonite mixtures with pumice additivite under high temperature

2020 ◽  
Vol 205 ◽  
pp. 04004
Author(s):  
Esra Güneri ◽  
Yeliz Yükselen Aksoy
Keyword(s):  
Shear Strength ◽  
High Temperature ◽  
Room Temperature ◽  
Engineering Properties ◽  
Direct Shear ◽  
Test Results ◽  
Soil Behavior ◽  
Shear Tests ◽  
Volume Deformation ◽  
Direct Shear Tests

Depending on increase in the number and type of energy geostructures, studies on the change in soil behavior against heat increase becomes more important. The engineering properties such as permeability, volume deformation of surrounding soils around energy structures mustn’t alter in the presence of heat and thermal cycles. Pumice is a material used in many fields especially for thermal insulation. For that reason, pumice can be used for increasing the resistance of soils in the presence of heat. In this study, the shear strength behavior of sand-bentonite mixtures was investigated with pumice additive under high temperature. In the experiments, 10% and 20% pumice were added to 10% and 20% sand-bentonite mixtures and compaction, direct shear tests were conducted. The direct shear tests were performed both room temperature and under 80°C. The results have shown that the pumice additive increased the shear strength of sand-bentonite mixtures under high temperature when compared the test results under room temperature.

scholarly journals Analisis Kestabilan Lereng Berdasarkan Kekuatan Geser Massa Batuan Terhadap Perubahan Kandungan Air Pada Tambang Batubara Di Area Blok Menyango

PROMINE ◽  
2019 ◽  
Vol 7 (2) ◽  
pp. 71-77
Author(s):  
Novandri Kusuma Wardana
Keyword(s):  
Shear Strength ◽  
Natural Condition ◽  
Shear Failure ◽  
Friction Angle ◽  
Direct Shear ◽  
Test Results ◽  
Shear Tests ◽  
Direct Shear Tests ◽  
Wet Condition ◽  
The Impact

Mining activities is commonly to work with the problem of stability of rock mass, then befordesaining mine’s slope should know rock shear strength parameters, such as cohesion (c) andinternal friction angle value ( . Beside those parameters, also needed to know the impact ofwater content to the rocks. The water content will effect rock’s shear strength, proof by the rockcondition which is ductile when it is dry and soft when it is wet. Based on test results was doneusing sandstone with laboratory scale of direct shear test were analyzed using mohr – coulomband patton criteria (1966). It is known that the cohesion (c) of sandstone decreased from 510,35kPa at natural condition down to 133,75 kPa at wet condition. The internal friction angle ( ) alsodecreased from 54,56° at natural condition down to 48,45° at wet condition. The reduction of theshear strength is caused by fragments and clay minerals characteristics which are so reactiveand very easy to absorb water so that the cohesion of the sandstone reduce the active normalstress so that working the shear stress required to cause the shear failure becomeweaker. From the results, it is also known that the shear surface roughness had a lot ofinfluence on the shear strength the normal stresses applied on the direct shear tests werevery low under 20% of UCS.

Impact of Sample Preparation Procedure on the Test Results of Four US ITER TF Conductors

2010 ◽  
Vol 20 (3) ◽  
pp. 508-511 ◽  
Author(s):  
B Stepanov ◽  
P Bruzzone ◽  
R Wesche ◽  
N Martovetsky ◽  
D Hatfield ◽  
...  
Keyword(s):  
Sample Preparation ◽  
Preparation Procedure ◽  
Test Results ◽  
Sample Preparation Procedure

scholarly journals Sand- and Clay-Photocured-Geomembrane Interface Shear Characteristics Using Direct Shear Test

2021 ◽  
Vol 13 (15) ◽  
pp. 8201
Author(s):  
Lihua Li ◽  
Han Yan ◽  
Henglin Xiao ◽  
Wentao Li ◽  
Zhangshuai Geng
Keyword(s):  
Soil Surface ◽  
Friction Angle ◽  
Direct Shear ◽  
Tensile Crack ◽  
Shear Tests ◽  
Interface Shear ◽  
Direct Shear Tests ◽  
Carbon Black Powder ◽  
Shear Characteristics ◽  
Impermeable Layer

It is well known that geomembranes frequently and easily fail at the seams, which has been a ubiquitous problem in various applications. To avoid the failure of geomembrane at the seams, photocuring was carried out with 1~5% photoinitiator and 2% carbon black powder. This geomembrane can be sprayed and cured on the soil surface. The obtained geomembrane was then used as a barrier, separator, or reinforcement. In this study, the direct shear tests were carried out with the aim to investigate the interfacial characteristics of photocured geomembrane–clay/sand. The results show that a 2% photoinitiator has a significant effect on the impermeable layer for the photocured geomembrane–clay interface. As for the photocured geomembrane–sand interface, it is reasonable to choose a geomembrane made from a 4% photoinitiator at the boundary of the drainage layer and the impermeable layer in the landfill. In the cover system, it is reasonable to choose a 5% photoinitiator geomembrane. Moreover, as for the interface between the photocurable geomembrane and clay/sand, the friction coefficient increases initially and decreases afterward with the increase of normal stress. Furthermore, the friction angle of the interface between photocurable geomembrane and sand is larger than that of the photocurable geomembrane–clay interface. In other words, the interface between photocurable geomembrane and sand has better shear and tensile crack resistance.

scholarly journals Mechanical Properties and Micro Mechanism of Nano-Clay-Modified Soil Cement Reinforced by Recycled Sand

2021 ◽  
Vol 13 (14) ◽  
pp. 7758
Author(s):  
Biao Qian ◽  
Wenjie Yu ◽  
Beifeng Lv ◽  
Haibo Kang ◽  
Longxin Shu ◽  
...  
Keyword(s):  
Shear Strength ◽  
Void Ratio ◽  
Soil Mass ◽  
Direct Shear ◽  
Test Results ◽  
The Sustainable Development ◽  
Direct Shear Tests ◽  
Soil Cement ◽  
Nano Clay ◽  
New Material

To observe the effect of recycled sand and nano-clay on the improvement of the early strength of soil-cement (7d), 0%, 10%, 15% and 20% recycled sand were added. While maintaining a fixed moisture content of 30%, the ratios of each material are specified in terms of soil mass percentage. The shear strength of CSR (recycled sand blended soil-cement) was investigated by direct shear test and four groups of specimens (CSR-1, CSR-2, CSR-3 and CSR-4) were obtained. In addition, 8% nano-clay was added to four CSR groups to obtain the four groups of CSRN-1, CSRN-2, CSRN-3 and CSRN-4 (soil-cement mixed with recycled sand and nano-clay), which were also subjected to direct shear tests. A detailed analysis of the modification mechanism of soil-cement by recycled sand and nano-clay was carried out in combination with scanning electron microscopy (SEM) and IPP (ImagePro-Plus) software. The test results showed that: (1) CSR-3 has the highest shear strength due to the “concrete-like” effect of the incorporation of recycled sand. With the addition of 8% nano-clay, the overall shear strength of the cement was improved, with CSRN-2 having the best shear strength, thanks to the filling effect of the nano-clay and its high volcanic ash content. (2) When recycled sand and nano-clay were added to soil-cement, the improvement in shear strength was manifested in a more reasonable macroscopic internal structure distribution of soil-cement. (3) SEM test results showed that the shear strength was negatively correlated with the void ratio of its microstructure. The smaller the void ratio, the greater the shear strength. This shows that the use of reclaimed sand can improve the sustainable development of the environment, and at the same time, the new material of nano-clay has potential application value.

Sign in / Sign up

Export Citation Format

Share Document