scholarly journals Contrast Analysis of Polarization in Three-Beam Interference Lithography

2021 ◽  
Vol 11 (11) ◽  
pp. 4789
Author(s):  
Fuping Peng ◽  
Jing Du ◽  
Jialin Du ◽  
Simo Wang ◽  
Wei Yan
Keyword(s):  
Incident Angle ◽  
Interference Lithography ◽  
Beam Polarization ◽  
Polarization Angle ◽  
Te Mode ◽  
Interference System ◽  
Contrast Analysis ◽  
Set Up ◽  
Directional Component ◽  
The Relationship

This paper analyzes the effect of polarization and the incident angle on the contrasts of interference patterns in three-beam interference lithography. A non-coplanar laser interference system was set up to simulate the relationship between contrast, beam polarization, and the incident angle. Different pattern periods require different incident angles, which means different contrast losses in interference lithography. Two different polarization modes were presented to study the effects of polarization with different incident angles based on theoretical analysis simulations. In the case of the co-directional component TE polarization mode, it was demonstrated that the pattern contrast decreases with the increase in the incident angle and the contrast loss caused by the polarization angle error also grew rapidly. By changing the mode to azimuthal (TE-TE-TE) polarization, the contrast of the interference pattern can be ensured to remain above 0.97 even though the incident angle is large. In addition, TE-TE-TE mode can accept larger polarization angle errors. This conclusion provides a theoretical basis for the generation of high-contrast light fields at different incident angles, and the conclusion is also applicable to multi-beam interference lithography.

Development of Nanohole Array Patterned by Laser Interference Lithography Technique

2016 ◽  
Vol 675-676 ◽  
pp. 41-44
Author(s):  
N. Srisuai ◽  
Mati Horprathum ◽  
P. Eiamchai ◽  
P. Chindaudom ◽  
S. Boonruang ◽  
...  
Keyword(s):  
Beam Splitter ◽  
Incident Angle ◽  
Laser Source ◽  
Interference Lithography ◽  
Laser Interference Lithography ◽  
Laser Interference ◽  
Nanohole Array ◽  
Si Substrates ◽  
Set Up ◽  
Two Parameters

Periodic nanohole pattern was created in spin-coated photoresist S1805 on Si substrates by Laser Interference Lithography (LIL). Wavelength of a laser source used in the optical system is 442 nm with the photon energy 2.80 eV. The system was set up to employ two laser beams from a beam splitter to generate interference pattern and expose to the photoresist. There are two parameters (incident angle and exposure time) which are determined due to affecting the ordering and feature of nanohole array. Therefore, the relation of these two parameters and actual dose were investigated and theoretically analyzed to optimize the resolution of LIL technique for nanoholes. The prepared samples after developing in the M26A for 5 sec were analyzed by field-emission scanning electron microscopy (FE-SEM). The results show that the pitch of the pattern is 440 nm and the smallest hole size is 190 nm The best feature is found for a laser fluence of 140 mJ/cm2. This nanohole array patterned by LIL consists of periodic nanostructures for high density storage to fabricate various nanodevices.

The Effects of Drying Techniques on Clay-Rich Soil Texture

1974 ◽  
Vol 32 ◽  
pp. 466-467
Author(s):  
T. G. Naymik
Keyword(s):  
Critical Point ◽  
Liquid Nitrogen ◽  
Liquid Nitrogen Temperature ◽  
Drying Methods ◽  
Air Drying ◽  
Freeze Dried ◽  
Critical Point Drying ◽  
Set Up ◽  
The Relationship ◽  
Quartz Grains

Three techniques were incorporated for drying clay-rich specimens: air-drying, freeze-drying and critical point drying. In air-drying, the specimens were set out for several days to dry or were placed in an oven (80°F) for several hours. The freeze-dried specimens were frozen by immersion in liquid nitrogen or in isopentane at near liquid nitrogen temperature and then were immediately placed in the freeze-dry vacuum chamber. The critical point specimens were molded in agar immediately after sampling. When the agar had set up the dehydration series, water-alcohol-amyl acetate-CO2 was carried out. The objectives were to compare the fabric plasmas (clays and precipitates), fabricskeletons (quartz grains) and the relationship between them for each drying technique. The three drying methods are not only applicable to the study of treated soils, but can be incorporated into all SEM clay soil studies.

Work Stress and Organisational Citizenship Behaviours (OCBs) in Call Centers Employees

2015 ◽  
Vol 3 (1) ◽  
Author(s):  
Sunita ◽  
Urvashi Singh ◽  
Shalini Singh ◽  
Rajnee Sharma
Keyword(s):  
Negative Impact ◽  
Call Centers ◽  
Negative Relationship ◽  
Married Couples ◽  
Call Centre ◽  
Simple Correlation ◽  
Nuclear Families ◽  
Set Up ◽  
Stress At Work ◽  
The Relationship

The present study was conducted to examine the relationship between organisational stress and organisational citizenship behaviours (OCBs) in employees of call centers. The study also further explored as how stress at work set-up has negative impact on OCBs. A sample of 250 employees working in call centre of Gurgaon belonging to an age group of 25-30 years were selected on availability basis. All were working married couples living in nuclear families. Job stress survey (Spielberger & Vagg, 1999) and Organisational Citizenship Behaviour (Bateman & Organ, 1983) were administered. Data was analysed by using simple correlation and multiple regression. Results showed the negative relationship between organisational stress and OCBs. Results of regression analysis also exhibited the negative impact of stress on OCBs. The implications for the employees are discussed.

A Study on the Relationship Between Psychological Climate, Employee Engagement and Organizational Citizenship Behavior

2015 ◽  
Vol 6 (2) ◽  
Author(s):  
Ginu George ◽  
Binoy Joseph
Keyword(s):  
Employee Engagement ◽  
Organizational Citizenship ◽  
Organizational Citizenship Behavior ◽  
Academic Research ◽  
Psychological Climate ◽  
Citizenship Behavior ◽  
Set Up ◽  
Relationship Of ◽  
The Relationship

Employee engagement is becoming an important area of focus by many HR consultancies in the recent years. Organizations having engaged employees tend to out-perform than employees who are not engaged or disengaged, also it will enable them to compete better in their industry resulting in higher performance, lower turnover, more profitability etc., Despite of all this there are still some industries who are ignorant and neglect the importance of having engaged employees. Therefore there is a necessity for more of academic research on employee engagement which helps in creating awareness to these organizations about the prominence of focusing on employee engagement and the findings will also augments the existing literature on employee engagement. The study was conducted on 433 employees working in travel organizations set up in Bangalore with the purpose of determining the relationship psychological climate (antecedent) has on employee engagement and in turn its relationship with organizational citizenship behavior (outcome). The study also determines the mediating relationship of employee engagement between PC and OCB.

scholarly journals Application of intelligent orienteering based on Internet of things

2020 ◽  
Vol 2020 (1) ◽  
Author(s):  
Donghui Zhang ◽  
Ruijie Liu
Keyword(s):  
Internet Of Things ◽  
Network Architecture ◽  
Emergency Services ◽  
Simulation Experiment ◽  
Experimental Studies ◽  
Signal Stability ◽  
Anchor Nodes ◽  
Set Up ◽  
The Relationship ◽  
The Internet Of Things

Abstract Orienteering has gradually changed from a professional sport to a civilian sport. Especially in recent years, orienteering has been widely popularized. Many colleges and universities in China have also set up this course. With the improvement of people’s living conditions, orienteering has really become a leisure sport in modern people’s life. The reduced difficulty of sports enables more people to participate, but it also exposes a series of problems. As the existing positioning technology is relatively backward, the progress in personnel tracking, emergency services, and other aspects is slow. To solve these problems, a new intelligent orienteering application system is developed based on the Internet of things. ZigBee network architecture is adopted in the system. ZigBee is the mainstream scheme in the current wireless sensor network technology, which has many advantages such as convenient carrying, low power consumption, and signal stability. Due to the complex communication environment in mobile signal, the collected information is processed by signal amplification and signal anti-interference technology. By adding anti-interference devices, video isolators and other devices, the signal is guaranteed to the maximum extent. In order to verify the actual effect of this system, through a number of experimental studies including the relationship between error and traffic radius and the relationship between coverage and the number of anchor nodes, the data shows that the scheme studied in this paper has a greater improvement in comprehensive performance than the traditional scheme, significantly improving the accuracy and coverage. Especially the coverage is close to 100% in the simulation experiment. This research has achieved good results and can be widely used in orienteering training and competition.

A new underwater positioning model based on average sound speed

2021 ◽  
pp. 1-17
Author(s):  
Yixu Liu ◽  
Xiushan Lu ◽  
Shuqiang Xue ◽  
Shengli Wang
Keyword(s):  
Efficient Algorithm ◽  
Sound Speed ◽  
Incident Angle ◽  
Function Model ◽  
Positioning Accuracy ◽  
Correction Model ◽  
Model Based ◽  
Underwater Positioning ◽  
Speed Function ◽  
The Relationship

Abstract The layout of seafloor datum points is the key to constructing the seafloor geodetic datum network, and a reliable underwater positioning model is the prerequisite for achieving precise deployment of the datum points. The traditional average sound speed positioning model is generally adopted in underwater positioning due to its simple and efficient algorithm, but it is sensitive to incident angle related errors, which lead to unreliable positioning results. Based on the relationship between incident angle and sound speed, the sound speed function model considering the incident angle has been established. Results show that the accuracy of positioning is easily affected by errors related to the incident angle; the new average sound speed correction model based on the incident angle proposed in this paper is used to significantly improve the underwater positioning accuracy.

SET UP FOR GROWTH? — AN EXPLORATORY ANALYSIS OF THE RELATIONSHIP OF GROWTH INTENTION AND BUSINESS MODELS

2015 ◽  
Vol 19 (06) ◽  
pp. 1540009 ◽  
Author(s):  
SARAH MAHDJOUR
Keyword(s):  
Business Models ◽  
Theory Of The Firm ◽  
Past Research ◽  
Business Owners ◽  
Competitive Strategies ◽  
Consulting Services ◽  
And Performance ◽  
Set Up ◽  
Relationship Of ◽  
The Relationship

What do growth-oriented business models look like? While several economic theories, such as the theory of the firm, are based on the assumption that firms aim to maximise their profits, past research has shown that growth intention is heterogeneous among firms and that many business owners prefer to keep their firm at a size that they can manage with few resources. This paper explores the relationship of growth intention and business models, based on a sample of 135 German ICT businesses. Following an exploratory approach, Mann–Whitney U tests are applied to analyse how different business model designs correspond with different levels of growth intention. The results indicate that growth intention relates to business owners’ decisions regarding the provision of consulting services, the level of standardisation in offered products and services, the choice of addressed markets, the implementation of competitive strategies based on cost efficiency and of revenue streams based on one-time- and performance-based payments. Furthermore, the results show that growth oriented firms are no more likely than non-growth oriented firms to adapt their business models dynamically to changed internal or external conditions.

Theoretical study of micro-structure fabrication by multi-beam laser interference lithography with different polarization combinations

2021 ◽  
pp. 2150459
Author(s):  
Xiangxian Wang ◽  
Tianxu Jia ◽  
Jiankai Zhu ◽  
Yingwen Su ◽  
Liping Zhang ◽  
...  
Keyword(s):  
Manufacturing Industry ◽  
Structural Parameters ◽  
Interference Lithography ◽  
Polarization Angle ◽  
Laser Interference Lithography ◽  
Laser Interference ◽  
Micro Structure ◽  
Periodic Patterns ◽  
Beam Laser ◽  
Micro Structures

In this study, we systematically and comprehensively investigated the influence of polarization angle on the fabrication of micro-structures by multi-beam laser interference lithography. Using theoretical analysis and simulation, we studied the effect of different polarization combinations, i.e. transverse electric (TE) and transverse magnetic (TM) polarization combinations, on the characteristics of the micro-structures fabricated by three-, four-, and six-beam laser interference lithography. We successfully obtained micro-structures with different periodic patterns such as honeycomb dots, quasi-elliptic dots, different square dots, and quasi-triangular dots. The simulation results illustrate that polarization affects the formation of interference patterns, pattern contrasts, and periods. The methods discussed herein are simple, low cost, and allow excellent control over structural parameters, and hence are useful for the micro-structure manufacturing industry.

Islam, nationalism and state in the Muslim Caucasus

2014 ◽  
Vol 1 (2) ◽  
pp. 1-21
Author(s):  
Galina Yemelianova
Keyword(s):  
Continuous Process ◽  
Well Being ◽  
Seventh Century ◽  
Russian Orthodox ◽  
North Caucasus ◽  
The Caucasus ◽  
Russian North ◽  
Set Up ◽  
The Relationship

Following the break-up of the USSR in 1991 the Muslim peoples of the Caucasus – corresponding to present-day Azerbaijan and the Russian North Caucasus – have been in a continuous process of renegotiating their Islamic identity and the role of Islam in the processes of nation-building. This has involved a complex set of factors, including the correlation between the rise of Islam and socio-economic well-being (or the lack of it), the level and longevity of Islamic heritage, the relationship between Islam and the nature of the ruling post-Soviet Caucasian regimes, and the degree of susceptibility to the region’s exposure to foreign influences, Islamic and Western. This article examines some of these factors from an historical perspective, concentrating on how the political elites and the populace variously dealt with essentially external influences in the course of their centuries-long incorporation within successive political empires. From the seventh century AD these were Islamic, emanating from the Umayyad, Abbasid, Timurid, Ottoman and Safavid empires; and from the nineteenth century, Russian Orthodox and Soviet atheist. An analysis of the dynamics set up by these influences and the distinctively Caucasian Muslim responses to them is crucial in understanding how current elites and their antagonists in the region embrace, reject and otherwise instrumentalise Islam.

Ascertaining the Critical Thinking and Formal Reasoning Skills of Students

1998 ◽  
Vol 59 (1) ◽  
pp. 9-18
Author(s):  
Tock Keng Lim
Keyword(s):  
Critical Thinking ◽  
The United States ◽  
Philosophy For Children ◽  
Cognitive Level ◽  
Formal Reasoning ◽  
Concrete Objects ◽  
Reasoning Skills ◽  
Matthew Lipman ◽  
Set Up ◽  
The Relationship

Ascertaining the critical thinking and formal reasoning skills of students With the critical thinking movement gaining momentum at all levels of education in the United States and other countries, many thinking programmes have been developed. A thinking programme that emphasises process, teaching students how to think, rather than what to think, is the Philosophy for Children (P4C) programme, currently carried out in Singapore. A child, according to Matthew Lipman, the founder of the P4C programme, can reason deductively and logically, using concrete objects. In his specially written stories for children Lipman translated the abstract formulations to reasoning in a concrete way that children could understand. To determine whether primary and secondary pupils in Singapore can reason and do philosophy, a study was set up in 1992 to ascertain their reasoning skills. Two instruments were used: the New Jersey Test of Reasoning, developed in the early 1980s to evaluate the P4C programme, and the Test of Formal Reasoning, written by P. K. Arlin to measure the stage of intellectual and cognitive level of the student: concrete, high concrete, transitional, low formal or high formal. This article reports the findings of the study concerning the relationship between critical thinking as measured by the NJTR and concrete and formal reasoning as measured by the ATFR.

Sign in / Sign up

Export Citation Format

Share Document