scholarly journals A Systematical Characterization of TeO2–V2O5 Glass System Using Boron (III) Oxide and Neodymium (III) Oxide Substitution: Resistance Behaviors against Ionizing Radiation

2021 ◽  
Vol 11 (7) ◽  
pp. 3035
Author(s):  
H. O. Tekin ◽  
Shams A. M. Issa ◽  
G. Kilic ◽  
Hesham M. H. Zakaly ◽  
N. Tarhan ◽  
...  
Keyword(s):  
Gamma Ray ◽  
Effective Atomic Number ◽  
Mean Free Path ◽  
Radiation Shielding ◽  
Glass System ◽  
Buildup Factor ◽  
Attenuation Coefficients ◽  
Gamma Ray Attenuation ◽  
Buildup Factors

This study aimed to perform an extensive characterization of a 74.75TeO2–0.25V2O5–(25 − x)B2O3-xNd2O3 glass system with (x = 0, 0.5, 1.0, and 1.5 mol%) for radiation shielding properties. Linear and mass attenuation coefficients were determined using Phy-X PSD software and compared with the simulation using Monte Carlo software MCNPX (version 2.7.0). Half value layer, mean free path, tenth value layer, effective atomic number, exposure buildup factor, and energy absorption buildup factors of VTBNd0.0, VTBNd0.5, VTBNd1.0, and VTBNd1.5 glasses were determined, respectively. The results showed that boron (III) oxide and neodymium (III) oxide substitution has an obvious impact on the gamma ray attenuation properties of the studied glasses. It can be concluded that the VTBNd1.5 sample with the highest content of neodymium (III) oxide (1.5 mol%) is the superior sample for shielding of gamma radiation in the investigated energy range.

scholarly journals Enhancement of Bentonite Materials with Cement for Gamma-Ray Shielding Capability

Materials ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4697
Author(s):  
Ahmed M. El-Khatib ◽  
Mohamed Elsafi ◽  
Mohamed N. Almutiri ◽  
R. M. M. Mahmoud ◽  
Jamila S. Alzahrani ◽  
...  
Keyword(s):  
Gamma Ray ◽  
Mean Free Path ◽  
Radiation Shielding ◽  
Point Sources ◽  
Linear Attenuation Coefficient ◽  
Buildup Factor ◽  
Chemical Compositions ◽  
Attenuation Coefficients ◽  
Water Holding ◽  
Mixed Samples

The gamma-ray shielding ability of various Bentonite–Cement mixed materials from northeast Egypt have been examined by determining their theoretical and experimental mass attenuation coefficients, μm (cm2g−1), at photon energies of 59.6, 121.78, 344.28, 661.66, 964.13, 1173.23, 1332.5 and 1408.01 keV emitted from 241Am, 137Cs, 152Eu and 60Co point sources. The μm was theoretically calculated using the chemical compositions obtained by Energy Dispersive X-ray Analysis (EDX), while a NaI (Tl) scintillation detector was used to experimentally determine the μm (cm2g−1) of the mixed samples. The theoretical values are in acceptable agreement with the experimental calculations of the XCom software. The linear attenuation coefficient (μ), mean free path (MFP), half-value layer (HVL) and the exposure buildup factor (EBF) were also calculated by knowing the μm values of the examined samples. The gamma-radiation shielding ability of the selected Bentonite–Cement mixed samples have been studied against other puplished shielding materials. Knowledge of various factors such as thermo-chemical stability, availability and water holding capacity of the bentonite–cement mixed samples can be analyzed to determine the effectiveness of the materials to shield gamma rays.

scholarly journals Gamma-Ray Attenuation and Exposure Buildup Factor of Novel Polymers in Shielding Using Geant4 Simulation

Materials ◽  
2021 ◽  
Vol 14 (17) ◽  
pp. 5051
Author(s):  
Mahmoud T. Alabsy ◽  
Jamila S. Alzahrani ◽  
M. I. Sayyed ◽  
Mahmoud I. Abbas ◽  
Daria I. Tishkevich ◽  
...  
Keyword(s):  
Gamma Ray ◽  
Effective Atomic Number ◽  
Buildup Factor ◽  
Geant4 Simulation ◽  
Polybutylene Terephthalate ◽  
Attenuation Coefficients ◽  
High Energies ◽  
Gamma Ray Attenuation ◽  
Mass Attenuation Coefficients ◽  
Good Agreement

Polymers are often used in medical applications, therefore, some novel polymers and their interactions with photons have been studied. The gamma-ray shielding parameters for Polymethylpentene (PMP), Polybutylene terephthalate (PBT), Polyoxymethylene (POM), Polyvinylidenefluoride (PVDF), and Polychlorotrifluoroethylene (PCTFE) polymers were determined using the Geant4 simulation and discussed in the current work. The mass attenuation coefficients (μ/ρ) were simulated at low and high energies between 0.059 and 1.408 MeV using different radionuclides. The accuracy of the Geant4 simulated results were checked with the XCOM software. The two different methods had good agreement with each other. Exposure buildup factor (EBF) was calculated and discussed in terms of polymers under study and photon energy. Effective atomic number (Zeff) and electron density (Neff) were calculated and analyzed at different energies. Additionally, the half-value layer (HVL) of the polymers was evaluated, and the results of this parameter showed that PCTFE had the highest probability of interaction with gamma photons compared to those of the other tested polymers.

scholarly journals Newly Developed Vanadium-Based Glasses and Their Potential for Nuclear Radiation Shielding Aims: A Monte Carlo Study on Gamma Ray Attenuation Parameters

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3897
Author(s):  
Huseyin Ozan Tekin ◽  
Ghaida Bilal ◽  
Hesham M. H. Zakaly ◽  
Gokhan Kilic ◽  
Shams A. M. Issa ◽  
...  
Keyword(s):  
Glass Sample ◽  
Gamma Ray ◽  
Effective Conductivity ◽  
Effective Atomic Number ◽  
Mean Free Path ◽  
Radiation Shielding ◽  
Nuclear Radiation ◽  
Buildup Factor ◽  
Doped Glass

This study aimed to investigate different types of glasses based on the 46V2O5-46P2O5-(8-x) B2O3-xCuO system in terms of their nuclear radiation shielding properties. Accordingly, five different CuO-doped vanadate glasses were investigated extensively to determine the necessary gamma shielding parameters along with effective conductivity at 300,000 and buildup factors. Phy-x PSD software was used for determination of these vital parameters. Furthermore, these parameters, such as half value layer, tenth value layer, and mean free path were investigated in a broad energy range between 0.015 and 15 MeV. The results revealed that the amount of CuO reinforced in each sample plays an essential role in determination of the shielding abilities of the samples. The sample with the highest CuO content had the highest linear attenuation coefficient and mass attenuation coefficient values. Additionally, the lowest mean free path, half value layer, and tenth value layer values were recorded for glass sample VPCu8. There was an inverse relation between the effective conductivity and effective atomic number and photon energy; that is, as energy increases, the effective conductivity and effective atomic number decreased rapidly, especially in the regions of low energy. Glass sample VPCu8 reported the highest values for both parameters. Moreover, glass sample VPCu8 had the lowest exposure buildup factor and energy absorption buildup factor values. Our findings showed that CuO-reinforced vanadate glass composition, namely 46V2O5-46P2O5-8CuO, with a glass density of 2.9235 g/cm3, was reported to have superior gamma ray attenuation properties. These results would be helpful for scientists in determining the most appropriate additive rare earth type, as well as the most appropriate glass composition, to offer shielding characteristics similar to those described above, taking into consideration the criteria for usage and the needs of the community. The results of this research will be useful to the scientific community in evaluating the prospective characteristics of CuO-doped glass systems and related glass compositions. CuO-doped glass systems and associated glass compositions have a wide range of properties.

scholarly journals In Silicon Monte Carlo Simulation Trials for Investigation of V2O5 Reinforcement Effect on Ternary Zinc Borate Glasses: Nuclear Radiation Shielding Dynamics

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1158
Author(s):  
Huseyin O. Tekin ◽  
Shams A. M. Issa ◽  
Gokhan Kilic ◽  
Hesham M. H. Zakaly ◽  
Mohamed M. Abuzaid ◽  
...  
Keyword(s):  
Effective Atomic Number ◽  
Mean Free Path ◽  
Radiation Shielding ◽  
Nuclear Radiation ◽  
Zinc Borate ◽  
Linear Attenuation Coefficient ◽  
Buildup Factor ◽  
Glass Composites ◽  
Mcnpx Code ◽  
Negative Effect

In the current study, promising glass composites based on vanadium pentoxide (V2O5)-doped zinc borate (ZnB) were investigated in terms of their nuclear-radiation-shielding dynamics. The mass and linear attenuation coefficient, half-value layer, mean free path, tenth-value layer, effective atomic number, exposure-buildup factor, and energy-absorption-buildup factor were deeply simulated by using MCNPX code, Phy-X PSD code, and WinXcom to study the validation of ZBV1, ZBV2, ZBV3, and ZBV4 based on (100−x)(0.6ZnO-0.4B2O3)(x)(V2O5) (x = 1, 2, 3, 4 mol%) samples against ionizing radiation. The results showed that attenuation competencies of the studied glasses slightly changed while increasing the V2O5 content from 1 mol% to 4 mol%. The domination of ZnO concentration in the composition compared to B2O3 makes ZnO substitution with V2O5 more dominant, leading to a decrease in density. Since density has a significant role in the attenuation of gamma rays, a negative effect was observed. It can be concluded that the aforementioned substitution can negatively affect the shielding competencies of studied glasses.

scholarly journals Experimental Investigation of Radiation Shielding Competence of Bi2O3-CaO-K2O-Na2O-P2O5 Glass Systems

Materials ◽  
2021 ◽  
Vol 14 (17) ◽  
pp. 5061
Author(s):  
Dalal Abdullah Aloraini ◽  
Aljawhara H. Almuqrin ◽  
M. I. Sayyed ◽  
Hanan Al-Ghamdi ◽  
Ashok Kumar ◽  
...  
Keyword(s):  
Attenuation Coefficient ◽  
Gamma Ray ◽  
Effective Atomic Number ◽  
Mass Attenuation Coefficient ◽  
Radiation Shielding ◽  
The Other ◽  
Linear Attenuation Coefficient ◽  
Attenuation Coefficients ◽  
Positive Effect ◽  
Theoretical Results

The gamma-ray shielding features of Bi2O3-CaO-K2O-Na2O-P2O5 glass systems were experimentally reported. The mass attenuation coefficient (MAC) for the fabricated glasses was experimentally measured at seven energy values (between 0.0595 and 1.33 MeV). The compatibility between the practical and theoretical results shows the accuracy of the results obtained in the laboratory for determining the MAC of the prepared samples. The mass and linear attenuation coefficients (MACs) increase with the addition of Bi2O3 and A4 glass possesses the highest MAC and LAC. A downward trend in the linear attenuation coefficient (LAC) with increasing the energy from 0.0595 to 1.33 MeV is found. The highest LAC is found at 1.33 MeV (in the range of 0.092–0.143 cm−1). The effective atomic number (Zeff) follows the order B1 > A1 > A2 > A3 > A4. This order emphasizes that increasing the content of Bi2O3 has a positive effect on the photon shielding proficiencies owing to the higher density of Bi2O3 compared with Na2O. The half value layer (HVL) is also determined and the HVL for the tested glasses is computed between 0.106 and 0.958 cm at 0.0595 MeV. The glass with 10 mol% of Bi2O3 has lower HVL than the glasses with 0, 2.5, 5, and 7.5 mol% of Bi2O3. So, the A4 glass needs a smaller thickness than the other glasses to shield the same radiation. As a result of the reported shielding parameters, inserting B2O3 provides lower values of these three parameters, which in turn leads to the development of superior photons shields.

A Monte Carlo investigation of some important radiation parameters and tissue equivalency for photons below 1 keV in human tissues

2021 ◽  
Author(s):  
Mustafa Mohammad Rafiei ◽  
Sara Parsaei ◽  
Parminder Kaur ◽  
Kanwar J Singh ◽  
Mehmet Büyükyıldız ◽  
...  
Keyword(s):  
Atomic Number ◽  
Gamma Ray ◽  
Effective Atomic Number ◽  
Mean Free Path ◽  
Relative Difference ◽  
Eye Lens ◽  
Equivalent Material ◽  
Human Tissues ◽  
Attenuation Coefficients ◽  
Tissue Equivalent

Abstract The attenuation coefficients are important input values in estimating not only the dose and exposure in radiotherapy and medical imaging, but also in the proper design of photon shields. While studies are widely available above 1 keV, the attenuation coefficients of human tissues for photon energies less than 1 keV have not been studied yet. In this study, the attenuation coefficients of water and some human tissues were estimated for low energy photons using the MCNP6.1 code in the energy region 0.1 keV-1 keV. Mass attenuation coefficients were estimated at photon energies of 100, 150, 200, 250, 300, 350, 400, 450, 500, 550, 600, 650, 700, 750, 800, 850, 900, 950 and 1000 eV for water and ten human tissues (Soft, Breast, Lung, Bone, Brain, Eye lens, Ovary, Skin, Thyroid and Prostate). Results were compared with those available in literature and a fairly good agreement has been obtained. These data were then used to calculate the mean free path, half value layer, tenth value layer, effective atomic number and specific gamma-ray constant (useful for calculation of dose rate) as well. Moreover, for comparison the effective atomic number of the water has been obtained using the results of this work and using the data available in NIST database from 0.1 to 1 keV. In addition, the human tissues were compared with some tissue equivalent materials in terms of effective atomic number and specific gamma-ray constant to study the tissue equivalency from the results, the muscle-equivalent liquid with sucrose has been found to be the best tissue equivalent material for soft tissue, eye lens and brain with relative difference below 4.1%.

Gamma radiation shielding properties of glasses within the TeO2-TiO2-ZnO system

2019 ◽  
Vol 107 (6) ◽  
pp. 517-522 ◽  
Author(s):  
M. Almatari
Keyword(s):  
Gamma Radiation ◽  
Attenuation Coefficient ◽  
Atomic Number ◽  
Effective Atomic Number ◽  
Mean Free Path ◽  
Mass Attenuation Coefficient ◽  
Radiation Shielding ◽  
Glass System ◽  
Shielding Properties ◽  
Mass Attenuation

Abstract Radiations are widely used in hospitals and health services in radiotherapy and molecular imaging using x-ray and gamma radiation which considered as the most penetrating radiations and very difficult to shield. In this study, the radiation shielding properties of different zinc oxide (ZnO) concentrations of the (95-x)TeO2-5TiO2-xZnO (x=5, 10, 15, 20, 25, 30 and 40 mol%) glass system was investigated to be introduced as a new transparency effective shielding material. In order to study shielding properties, mass attenuation coefficients in the energy range of 0.015–15 MeV photon energies for the current glass system were calculated using ParShield software. Moreover, half value layer, mean free path and effective atomic number were evaluated using the obtained attenuation coefficient. The results indicated that if ZnO was added to the current glass system the mass attenuation coefficient will be decreased as well as effective atomic number values. The highest mass attenuation coefficient at all energies was found to be in TT5Z5 glass sample as well as the effective atomic number value.

scholarly journals Tailoring bismuth borate glasses by incorporating PbO/GeO2 for protection against nuclear radiation

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Ashok Kumar ◽  
Anisha Jain ◽  
M. I. Sayyed ◽  
Farah Laariedh ◽  
K. A. Mahmoud ◽  
...  
Keyword(s):  
Radiation Protection ◽  
Photon Energy ◽  
Effective Atomic Number ◽  
Mean Free Path ◽  
Radiation Shielding ◽  
Nuclear Radiation ◽  
Neutron Shielding ◽  
Bismuth Borate ◽  
Removal Cross Section ◽  
Buildup Factors

AbstractNuclear radiation shielding capabilities for a glass series 20Bi2O3 − xPbO − (80 − 2x)B2O3 − xGeO2 (where x = 5, 10, 20, and 30 mol%) have been investigated using the Phy-X/PSD software and Monte Carlo N-Particle transport code. The mass attenuation coefficients (μm) of selected samples have been estimated through XCOM dependent Phy-X/PSD program and MCNP-5 code in the photon-energy range 0.015–15 MeV. So obtained μm values are used to calculate other γ-ray shielding parameters such as half-value layer (HVL), mean-free-path (MFP), etc. The calculated μm values were found to be 71.20 cm2/g, 76.03 cm2/g, 84.24 cm2/g, and 90.94 cm2/g for four glasses S1 to S4, respectively. The effective atomic number (Zeff)values vary between 69.87 and 17.11 for S1 or 75.66 and 29.11 for S4 over 0.05–15 MeV of photon-energy. Sample S4, which has a larger PbO/GeO2 of 30 mol% in the bismuth-borate glass, possesses the lowest MFP and HVL, providing higher radiation protection efficiency compared to all other combinations. It shows outperformance while compared the calculated parameters (HVL and MFP) with the commercial shielding glasses, different alloys, polymers, standard shielding concretes, and ceramics. Geometric Progression (G-P) was applied for evaluating the energy absorption and exposure buildup factors at energies 0.015–15 MeV with penetration depths up to 40 mfp. The buildup factors showed dependence on the MFP and photon-energy as well. The studied samples' neutron shielding behavior was also evaluated by calculating the fast neutron removal cross-section (ΣR), i.e. found to be 0.139 cm−1 for S1, 0.133 cm−1 for S2, 0.128 cm−1 for S3, and 0.12 cm−1 for S4. The results reveal a great potential for using a glass composite sample S4 in radiation protection applications.

scholarly journals Study of Gamma Ray Exposure Buildup Factor for Some Ceramics with Photon Energy, Penetration Depth and Chemical Composition

2013 ◽  
Vol 2013 ◽  
pp. 1-6 ◽  
Author(s):  
Tejbir Singh ◽  
Gurpreet Kaur ◽  
Parjit S. Singh
Keyword(s):  
Silicon Carbide ◽  
Chemical Composition ◽  
Penetration Depth ◽  
Photon Energy ◽  
Gamma Ray ◽  
Magnesium Diboride ◽  
Mean Free Path ◽  
Buildup Factor ◽  
Fitting Method ◽  
Buildup Factors

Gamma ray exposure buildup factor for some ceramics such as boron nitride (BN), magnesium diboride (MgB2), silicon carbide (SiC), titanium carbide (TiC) and ferrite (Fe3O4) has been computed using five parametric geometric progression (G.P.) fitting method in the energy range of 0.015 to 15.0 MeV, up to the penetration of 40 mean free path (mfp). The variation of exposure buildup factors for all the selected ceramics with incident photon energy, penetration depth, and chemical composition has been studied.

scholarly journals Investigation of the Mass Attenuation Coefficients, Effective Atomic Numbers and Electron Densities for Compounds of Painkiller

2021 ◽  
Vol 2 (1) ◽  
pp. 034-037
Author(s):  
Tekerek Saniye
Keyword(s):  
Gamma Ray ◽  
Effective Atomic Number ◽  
Radiation Shielding ◽  
Radiation Physics ◽  
Attenuation Coefficients ◽  
Effective Electron ◽  
Technological Advances ◽  
Mass Attenuation Coefficients ◽  
Effective Atomic Numbers ◽  
Gamma Radiations

In this study the effects of gamma radiations with compounds are an important subject in the field of medicine, radiation shielding and radiation physics. With technological advances the using of radiation has increased in the medicine in the last century. The mass absorpsion coefficient (µ/ρ) is the fundamental a quantity characterizing gamma ray and is of major importance in radiation shielding. In this study, the mass absorption coefficient of painkillers named Ketoprofen, Flurbiprofen, Etodolac, Ibuprofen, Meloxicam, Diclofenac and Aspirin were calculated at energy range from 4.65 keV to 59.543 keV using the WinXCom data programme. In addition total atomic (σta), moleculer (σtm), electronic cross-section (σte), effective atomic number (Zeff), effective electron density (Neff) were calculated.

Sign in / Sign up

Export Citation Format

Share Document