scholarly journals Advanced Modelling and Risk Analysis of RC Buildings with Sliding Isolation Systems Designed by the Italian Seismic Code

2021 ◽  
Vol 11 (4) ◽  
pp. 1938 ◽  
Author(s):  
Felice Carlo Ponzo ◽  
Antonio Di Cesare ◽  
Alessio Telesca ◽  
Alberto Pavese ◽  
Marco Furinghetti
Keyword(s):  
Risk Analysis ◽  
Seismic Isolation ◽  
Limit State ◽  
Seismic Intensity ◽  
Intensity Level ◽  
Isolation System ◽  
Isolation Technique ◽  
Existing Building ◽  
Displacement Capacity ◽  
Ultimate Displacement

Double Curved Concave Surface Sliders (DCCSS) are seismic isolators based on the pendulum principle widely used worldwide. Coherently with European code, DCCSS do not include any mechanical elements as end-stopper. In case of displacement higher than those associated with the design earthquakes, the inner slider runs on the edge of the sliding surfaces beyond their geometric displacement capacity keeping the ability to support gravity loads. In this paper, the advanced modelling and risk analysis of reinforced concrete (RC) base-isolated buildings designed for medium and high seismicity zones according to the Italian code has been assessed considering new construction and existing structures retrofitted using the seismic isolation technique. Pushover analyses and nonlinear dynamic analyses including inelastic superstructure behaviour and the over-stroke displacement of the isolation system have been carried out. Annual rates of failure are computed for Usability-Preventing Damage (UPD) related to the superstructure inter-storey drift and for Global Collapse (GC) associated with the ultimate displacement of the DCCSS. Moreover, the ultimate displacement is assumed with an extra-displacement of more than 30% of the maximum geometrical displacement. Results pointed out that in the case of new buildings the GC and UPD conditions occur almost at the same seismic intensity, while for the cases of the existing building, the UPD is the dominant limit state, being reached at an intensity level lower than GC.

scholarly journals Evaluating Collapse Fragility Curves for Existing Buildings Retrofitted Using Seismic Isolation

2020 ◽  
Vol 10 (8) ◽  
pp. 2844
Author(s):  
Amedeo Flora ◽  
Giuseppe Perrone ◽  
Donatello Cardone
Keyword(s):  
Seismic Isolation ◽  
Failure Modes ◽  
Base Isolation ◽  
Fragility Curves ◽  
Limit State ◽  
Spectral Acceleration ◽  
Existing Buildings ◽  
Isolation System ◽  
Isolation Technique ◽  
Design Earthquake

Few studies have investigated so far the collapse capacity of buildings with base-isolation. In such studies, preliminary considerations have been drawn based on a number of assumptions regarding: (i) the methodology used for assessing the collapse capacity, (ii) the collapse conditions and failure modes assumed for both superstructure and isolation system, and (iii) the numerical modeling assumptions. The main results pointed out that the collapse conditions of base-isolated buildings may occur for intensity levels slightly higher than those associated with the design earthquake. In this paper, further developments are made through the use of enhanced models for the description of the behavior of a rubber-based isolation system and the assumption of more rational collapse conditions. Collapse fragility functions, in terms of mean and dispersion values, are proposed for two archetypes representative of existing buildings retrofitted using the seismic isolation technique. The collapse margin ratio (median collapse capacity Sa,C, namely the spectral acceleration associated to a probability of exceedance equal to 50%, divided by the design spectral acceleration at the collapse prevention limit state) has been evaluated for each examined case-study. Values ranging from 1.10 to 1.45 were found.

Geotechnical Seismic Isolation System - Experimental Study

2010 ◽  
Vol 163-167 ◽  
pp. 4449-4453
Author(s):  
Wei Xiong ◽  
Hing Ho Tsang ◽  
S.H. Lo ◽  
Shou Ping Shang ◽  
Hai Dong Wang ◽  
...  
Keyword(s):  
Seismic Isolation ◽  
Dynamic Performance ◽  
Testing Procedure ◽  
Shaking Table ◽  
Isolation System ◽  
Isolation Technique ◽  
Sand Mixture ◽  
Seismic Hazard Mitigation ◽  
Constituent Material ◽  
Different Levels

In this study, an experimental investigation program on a newly proposed seismic isolation technique, namely “Geotechnical Seismic Isolation (GSI) system”, is conducted with an aim of simulating its dynamic performance during earthquakes. The testing procedure is three-fold: (1) A series of cyclic simple shear tests is conducted on the key constituent material of the proposed GSI system, i.e., rubber-sand mixture (RSM) in order to understand its behavior under cyclic loadings. (2) The GSI system is then subjected to a series of shaking table tests with different levels of input ground shakings. (3) By varying the controlling parameters such as percentage of rubber in RSM, thickness of RSM layer, coupled with the weight of superstructure, a comprehensive parametric study is performed. This experimental survey demonstrates the excellent performance of the GSI system for potential seismic hazard mitigation.

Evaluation of the Isolation System Influence in the Seismic Loading Analysis Applied to a Near Term Deployment Reactor

2009 ◽  
Author(s):  
R. Lo Frano ◽  
G. Forasassi
Keyword(s):  
Nuclear Power ◽  
Seismic Isolation ◽  
Seismic Waves ◽  
Base Isolation ◽  
Methodological Approach ◽  
Response Spectra ◽  
Three Dimensional Model ◽  
Isolation System ◽  
Isolation Technique ◽  
Near Term

Nuclear power plant (NPP) design is strictly dependent on the seismic hazards and safety aspects related to the external events of the site. Passive vibration isolators are the most simple and reliable means to protect sensitive equipment from environmental shocks and vibrations. This paper concerns the methodological approach to treat isolation applied to a near term deployment reactor and its internals structures in order to attain a suitable decrease of response spectra at each floor along the height of the structure. The aim of this evaluation is to determine the seismic resistance capability of as-built structures systems and components in the event of the considered Safe Shutdown earthquake (SSE). The use of anti-seismic techniques, such as seismic isolation (SI) and passive energy dissipation, seems able to ensure the full integrity and operability of important structures and systems even in very severe seismic conditions. Therefore the seismic dynamic loadings, propagated up to the main reactor system and components, may be reduced by using the developed base-isolation system (high flexibility for horizontal motions) that might combine suitable dampers with the isolating components to support reactor structures and building. To investigate and analyze the effects of the mentioned earthquake on the considered reactor internals, a deterministic methodological approach, based on the evaluation of the propagation of seismic waves along the structure, was used. To the purpose of this study a numerical assessment of dynamic structural response behaviour of the structures was accomplished by means of the finite element approach and setting up, as accurately as possible, a representative three-dimensional model of mentioned NPP structures. The obtained results in terms of response spectra (carried out from both cases of isolated and not isolated seismic analyses) were compared in order to highlight the isolation technique effectiveness.

scholarly journals Seismic Base Isolation System using Scrap Old Tyres

2020 ◽  
Vol 5 (3) ◽  
pp. 85-90
Keyword(s):  
Seismic Isolation ◽  
Structural Engineering ◽  
Base Isolation ◽  
Shock Propagation ◽  
Analysis Tool ◽  
Element Analysis ◽  
Isolation System ◽  
Isolation Technique ◽  
Base Isolation System ◽  
Seismic Vibrations

Enfeebling the effects of vibration caused by the movement of tectonic plates has been the major topic of research in the field of Structural Engineering. Base isolation is a technique used to counteract the effects of seismic vibration and ensuring the safety of the superstructure. Even though, the strategy of base isolation has been used in interminable number of structures, there is a need for economized, effective base isolation technique. India has been recycling and reusing waste tyres for four decades, it is estimated that 60% are disposed of through illegal dumping. India, being the second largest manufacturer of rubber after China, there is a menace of rubber disposal in the country. Despite the numerous efforts of technologists of recycling and utilizing the scrap rubber tyres, 17% of the scrap rubber tyres are diverted to landfill creating disposal problem. Therefore, there is a need for utilizing the used scrap rubber tyres in an innovative way instead of dumping it. Scrap Rubber tyres, being elastic in nature serve to be a potential shock absorber of seismic vibrations. In the present study, an attempt is made to utilize the recycled scrap rubber tyre in seismic isolation of structure. This technique proves to be a low- cost earthquake mitigation technique which can potentially reduce the damage caused by seismic shock propagation into the structure and hence ensure overall safety of the structure. An experimental analysis is done to evaluate the properties of assembly of rubber tyres and utilization of the same for isolating base of structures to check for the effectiveness in enfeebling the shocks produced by seismic vibrations. Furthermore, using the properties of scrap rubber tyres obtained from the experimental results, performance of the scrap tyres as a base isolation system for a multistoried building and stability of the structure was studied using Finite element analysis tool.

scholarly journals Seismic Isolation System using U-Shaped Steel Damper

2019 ◽  
Vol 8 (4) ◽  
pp. 12336-12339
Keyword(s):  
Seismic Isolation ◽  
Base Isolation ◽  
Structural Response ◽  
Time History ◽  
Earthquake Ground Motion ◽  
Isolation System ◽  
Isolation Technique ◽  
Base Isolation System ◽  
The Time Domain ◽  
External Forces

In the present paper base isolation system is analyzed and its seismic behavior is investigated using U-shaped steel dampers as an isolator by placing it at the bottom of the structure. It is the most popular way of protecting the structure using control techniques for earthquake ground motion. The dampers significantly reduced damage factors such as displacement and drift. To reduce structural response to external forces, which can be accomplished through the use of special protective systems. So to prevent these damages, seismic isolation technique can be used for newly constructed structures. The time history analysis of the time domain on this structure is conducted by using SAP2000 software

Seismic Risk Analysis of Bridge Structures Based on Total Probability Theorem

2012 ◽  
Vol 446-449 ◽  
pp. 1085-1093
Author(s):  
Guo Liang Wang ◽  
Jian Min Wang
Keyword(s):  
Risk Analysis ◽  
Seismic Risk ◽  
Hazard Analysis ◽  
Limit State ◽  
Seismic Intensity ◽  
Total Probability ◽  
Seismic Risk Analysis ◽  
Specific Level ◽  
Structure Damage ◽  
Bridge Structures

Considering the uncertainties in structural capacities and seismic motions, a probabilistic-based seismic risk analysis approach for bridges is proposed in this paper. In this approach, the Total Probability Theory (TPT) is used to divide seismic risk analysis into three main steps: seismic hazard analysis; structure damage analysis; and failure probability analysis. The parameters of seismic risk analysis are assumed to be an independent and discrete Markov process, resulting in rigorous and consistent seismic risk functions for calculating the annual average probability of exceeding a designated limit state of structure under a specific level of seismic intensity. A case study of seismic risk analysis was performed on a three-span continuous rigid-frame bridge. The results show that the approach presented in the paper is applicable for the seismic risk analysis of bridge structures, and is an effective tool to assess the performance of bridge structures under earthquake actions.

Dynamic Behaviour of Seismically Isolated Cylindrical Offshore Storage Tanks

2005 ◽  
Author(s):  
Nijat Mastan-Zade ◽  
Gokhan Yazici
Keyword(s):  
Seismic Isolation ◽  
Storage Tanks ◽  
Environmental Disaster ◽  
Isolation System ◽  
Isolation Technique ◽  
Fixed Base ◽  
Internal Forces ◽  
Water Proof ◽  
Stiffness And Damping ◽  
The Mathematical Model

Cylindrical offshore storage tanks are mainly used to store critical liquids such as petroleum and LNG. Failure of these tanks after an earthquake not only results in high financial losses but can also create an environmental disaster as well. Seismic isolation technique has been utilized in this study to mitigate the damaging effects of lateral earthquake forces. In this study, seismic isolation is used in cylindrical offshore storage tanks. Seismic isolators are protected from the marine environment by a water-proof flexible membrane that allows the horizontal movement of the tank. The mathematical model takes the following into account: mass of the stored liquid, added mass of the water surrounding the tank, horizontal stiffness and damping of the isolation system. Internal forces due to the hydrostatic and hydrodynamic forces acting on the system during an earthquake have been calculated by using the shell-moment theory. The results of the analyses are compared for both the isolated and fixed-base tanks.

Isolation Performance of Intelligent Seismic Isolation System Using Air Bearing

2009 ◽  
Author(s):  
Satoshi Fujita ◽  
Keisuke Minagawa ◽  
Mitsuru Miyazaki ◽  
Go Tanaka ◽  
Toshio Omi ◽  
...  
Keyword(s):  
Seismic Isolation ◽  
Seismic Waves ◽  
Three Dimensional ◽  
Vertical Motion ◽  
Air Bearings ◽  
Natural Period ◽  
Isolation System ◽  
Vertical Excitation ◽  
Long Period ◽  
Isolation Performance

This paper describes three-dimensional isolation performance of seismic isolation system using air bearings. Long period seismic waves having predominant period of from a few seconds to a few ten seconds have recently been observed in various earthquakes. Also resonances of high-rise buildings and sloshing of petroleum tanks in consequence of long period seismic waves have been reported. Therefore the isolation systems having very long natural period or no natural period are required. In a previous paper [1], we proposed an isolation system having no natural period by using air bearings. Additionally we have already reported an introduction of the system, and have investigated horizontal motion during earthquake in the previous paper. It was confirmed by horizontal vibration experiment and simulation in the previous paper that the proposed system had good performance of isolation. However vertical motion should be investigated, because vertical motion varies horizontal frictional force. Therefore this paper describes investigation regarding vertical motion of the proposed system by experiment. At first, a vertical excitation test of the system is carried out so as to investigate vertical dynamic property. Then a three-dimensional vibration test using seismic waves is carried out so as to investigate performance of isolation against three-dimensional seismic waves.

scholarly journals Dynamic Characteristics of the Bouc–Wen Nonlinear Isolation System

2021 ◽  
Vol 11 (13) ◽  
pp. 6106
Author(s):  
Zhiying Zhang ◽  
Xin Tian ◽  
Xin Ge
Keyword(s):  
Dynamic Characteristics ◽  
Seismic Isolation ◽  
Influence Factors ◽  
Harmonic Balance Method ◽  
Control Parameters ◽  
Hysteretic Model ◽  
Incremental Harmonic Balance Method ◽  
Isolation System ◽  
Nonlinear Dynamic Characteristics ◽  
Incremental Harmonic Balance

The Bouc–Wen nonlinear hysteretic model has many control parameters, which has been widely used in the field of seismic isolation. The isolation layer is the most important part of the isolation system, which can be effectively simulated by the Bouc–Wen model, and the isolation system can reflect different dynamic characteristics under different control parameters. Therefore, this paper mainly studies and analyzes the nonlinear dynamic characteristics of the isolation system under different influence factors based on the incremental harmonic balance method, which can provide the basis for the dynamic design of the isolation system.

Vulnerability-Based Design of Sliding Concave Bearings for the Seismic Isolation of Steel Storage Tanks

2016 ◽  
Author(s):  
Hoang Nam Phan ◽  
Fabrizio Paolacci ◽  
Silvia Alessandri ◽  
Phuong Hoa Hoang
Keyword(s):  
Liquid Steel ◽  
Seismic Isolation ◽  
Failure Modes ◽  
Fragility Curves ◽  
Time History ◽  
Probability Of Failure ◽  
Design Parameters ◽  
Economic Losses ◽  
Storage Tanks ◽  
Isolation System

Liquid steel storage tanks are strategic structures for industrial facilities and have been widely used both in nuclear and non-nuclear power plants. Typical damage to tanks occurred during past earthquakes such as cracking at the bottom plate, elastic or elastoplastic buckling of the tank wall, failure of the ground anchorage system, and sloshing damage around the roof, etc. Due to their potential and substantial economic losses as well as environmental hazards, implementations of seismic isolation and energy dissipation systems have been recently extended to liquid storage tanks. Although the benefits of seismic isolation systems have been well known in reducing seismic demands of tanks; however, these benefits have been rarely investigated in literature in terms of reduction in the probability of failure. In this paper, A vulnerability-based design approach of a sliding concave bearing system for an existing elevated liquid steel storage tank is presented by evaluating the probability of exceeding specific limit states. Firstly, nonlinear time history analyses of a three-dimensional stick model for the examined case study are performed using a set of ground motion records. Fragility curves of different failure modes of the tank are then obtained by the well-known cloud method. In the following, a seismic isolation system based on concave sliding bearings is proposed. The effectiveness of the isolation system in mitigating the seismic response of the tank is investigated by means of fragility curves. Finally, an optimization of design parameters for sliding concave bearings is determined based on the reduction of the tank vulnerability or the probability of failure.

Sign in / Sign up

Export Citation Format

Share Document