scholarly journals Simplified Calibration Method for Constant-Temperature Hot-Wire Anemometry

2020 ◽  
Vol 10 (24) ◽  
pp. 9058
Author(s):  
Hidemi Takahashi ◽  
Mitsuru Kurita ◽  
Hidetoshi Iijima ◽  
Seigo Koga
Keyword(s):  
Boundary Layer ◽  
Flow Velocity ◽  
Constant Temperature ◽  
Calibration Method ◽  
Large Temperature ◽  
Velocity Data ◽  
Hot Wire ◽  
Temperature Variations ◽  
Wire Temperature ◽  
Hot Wire Anemometry

This study proposes a unique approach to convert a voltage signal obtained from a hot-wire anemometry to flow velocity data by making a slight modification to existing temperature-correction methods. The approach was a simplified calibration method for the constant-temperature mode of hot-wire anemometry without knowing exact wire temperature. The necessary data are the freestream temperature and a set of known velocity data which gives reference velocities in addition to the hot-wire signal. The proposed method was applied to various boundary layer velocity profiles with large temperature variations while the wire temperature was unknown. The target flow velocity was ranged between 20 and 80 m/s. By using a best-fit approach between the velocities in the boundary layer obtained by hot-wire anemometry and by the pitot-tube measurement, which provides reference data, the unknown wire temperature was sought. Results showed that the proposed simplified calibration approach was applicable to a velocity range between 20 and 80 m/s and with temperature variations up to 15 °C with an uncertainty level of 2.6% at most for the current datasets.

Calibration of Constant-Temperature Hot-Wire Anemometers at Low Velocities in Water with Variable Fluid Temperature

1972 ◽  
Vol 94 (1) ◽  
pp. 17-22 ◽  
Author(s):  
K. Hollasch ◽  
B. Gebhart
Keyword(s):  
Experimental Study ◽  
Natural Convection ◽  
Constant Temperature ◽  
Fluid Temperature ◽  
Hot Wire ◽  
Temperature Variations ◽  
Wire Probe ◽  
Temperature Mode

Calibration of hot-wire probes operated in a constant-temperature mode in water at low velocities is discussed. Operation under circumstances where natural convection effects are important is considered. A method of calibrating a constant-temperature hot-wire probe for variations in fluid temperature is presented. The method consists of varying wire overheat during calibration at a constant fluid temperature. A relation is derived analytically relating anemometer output with a variable overheat resistance to anemometer output with fluid temperature variations. An experimental study to verify the analysis is presented.

Use of hot-wire anemometry for measuring the nanopowder flow velocity

2012 ◽  
Vol 47 (2) ◽  
pp. 281-287 ◽  
Author(s):  
S. P. Bardakhanov ◽  
V. I. Lysenko ◽  
D. Yu. Trufanov
Keyword(s):  
Flow Velocity ◽  
Hot Wire ◽  
Hot Wire Anemometry

Static and dynamic calibrations of constant-temperature hot-wire systems

1971 ◽  
Vol 47 (4) ◽  
pp. 765-777 ◽  
Author(s):  
A. E. Perry ◽  
G. L. Morrison
Keyword(s):  
Constant Temperature ◽  
Calibration Method ◽  
Calibration Procedure ◽  
Hot Wire ◽  
Low Frequencies ◽  
Conventional Procedure ◽  
Vortex Streets ◽  
Karman Vortex ◽  
System Frequency ◽  
Wire System

The conventional hot-wire static calibration procedure for the measurement of absolute turbulence intensities with constant-temperature hot-wire anemometers is investigated and serious errors are found. An alternative calibration procedure is developed which involves shaking the wire at low frequencies in a uniform flow. A series of tests indicate that this dynamic calibration method is more accurate and consistent than the conventional procedure.A method for verifying various calibration procedures is demonstrated. This method involves the measurement of velocity perturbations in a series of Karman vortex streets. The velocity perturbation amplitude is held fixed, but the frequency varies from one vortex street to another. This method also acts as a direct check of the hot-wire system frequency response.

Investigation of Hot Film Calibration for Entropy Generation Rate Calculations

2002 ◽  
Author(s):  
R. Mahon ◽  
P. Frawley ◽  
M. R. D. Davies
Keyword(s):  
Boundary Layer ◽  
Numerical Methods ◽  
Circular Cylinder ◽  
Constant Temperature ◽  
Entropy Generation ◽  
Cross Flow ◽  
Entropy Generation Rate ◽  
Hot Wire ◽  
Hot Film ◽  
The Relationship

The objective of this paper is to investigate in detail the relationship between results obtained from flow over a circular cylinder in cross flow using Hot Film and Hot Wire Constant Temperature Anemometry (C.T.A.). The experimental results are compared with those obtained using numerical methods. The results obtained from Hot Wire Anemometry are used to attempt to calibrate the Hot Film Sensors for the purpose of evaluating entropy generation rates in the boundary layer of the cylinder.

A possible reinterpretation of the Princeton superpipe data

2001 ◽  
Vol 439 ◽  
pp. 395-401 ◽  
Author(s):  
A. E. PERRY ◽  
S. HAFEZ ◽  
M. S. CHONG
Keyword(s):  
Boundary Layer ◽  
Reynolds Numbers ◽  
Additive Constant ◽  
Velocity Data ◽  
Hot Wire ◽  
Mean Velocity ◽  
Displacement Effect ◽  
Law Of The Wall ◽  
Hot Wires ◽  
Logarithmic Law

In experiments recently performed at Melbourne, Pitot-tube mean velocity profiles in a boundary layer disagreed with those obtained with hot wires. The standard MacMillan (1956) correction for the probe displacement effect and a correction for turbulence intensity were both required for obtaining agreement between the two sets of mean velocity data. We were thus motivated to reanalyse the Princeton superpipe data using the same two corrections. The result is a plausible conclusion that the superpipe is rough at the higher Reynolds numbers and its data follow the Colebrook (1939) formula for commercial pipes rather well. It also appears that the logarithmic law of the wall is valid, with a Kármán constant close to that found recently by Österlund (1999) from boundary layer measurements with a hot wire. The smooth regime in the pipe gave almost the same additive constant for the log-law as Österlund's. A comparison between the superpipe data and the pipe data of Perry, Henbest & Chong (1997) suggests that the conventional velocity defect law may be valid down to lower Reynolds numbers than concluded by Zagarola & Smits (1998).

Modelling and operation of sub-miniature constant temperature hot-wire anemometry

2016 ◽  
Vol 27 (12) ◽  
pp. 125301 ◽  
Author(s):  
M Samie ◽  
J H Watmuff ◽  
T Van Buren ◽  
N Hutchins ◽  
I Marusic ◽  
...  
Keyword(s):  
Constant Temperature ◽  
Hot Wire ◽  
Hot Wire Anemometry

scholarly journals Bypass Boundary Layer Transition on Flat Plate by Adverse Pressure Gradient

2019 ◽  
Vol 213 ◽  
pp. 02077
Author(s):  
Vladislav Skála ◽  
Václav Uruba ◽  
Pavel Antoš ◽  
Pavel Jonáš
Keyword(s):  
Boundary Layer ◽  
Wind Tunnel ◽  
Pressure Gradient ◽  
Flat Plate ◽  
Free Stream ◽  
Adverse Pressure Gradient ◽  
Boundary Layer Transition ◽  
Hot Wire ◽  
Layer Transition ◽  
Hot Wire Anemometry

Bypass boundary layer transition in flows on flat plate by adverse pressure gradient was investigated experimentally. It was measuered cases with combination of adverse pressure gradient by different free stream turbulence intenzity. Hot wire anemometry technique was used. Measuerement were made on flat plate in closed wind tunnel. Adverse pressure gradient was set by diffuser in tested section of wind tunnel. Grid turbulence of free stream was controlled by screen. Hot wire anemometry technique was used, intermitency factor was evaluated. Results were compared wih cases with simpliest conditions.

Sign in / Sign up

Export Citation Format

Share Document