scholarly journals Tensile Tests for the Improvement of Adhesion between Rubber and Steel Layers in Elastomeric Isolators

2020 ◽  
Vol 10 (22) ◽  
pp. 8063
Author(s):  
Margherita Pauletta ◽  
Federico Pinzano ◽  
Giada Frappa ◽  
Gaetano Russo
Keyword(s):  
Manufacturing Process ◽  
Seismic Isolation ◽  
Tensile Tests ◽  
Small Scale ◽  
Shear Tests ◽  
Good Adhesion ◽  
Single Body ◽  
Adhesion Behavior ◽  
Shear Strains ◽  
Direct Tensile

Steel reinforced elastomeric isolators are currently the most used bearings for seismic isolation purposes. The steel reinforcements are cut to the desired shape, sandblasted, cleaned with acid, and coated with bonding compound during the manufacturing process. Then the elastomer and steel layers are stacked in a mold and subjected to vulcanization so that they are glued together and constitute a single body. Good adhesion between the layers is very important for the correct functioning of the device. Adhesion conditions become critical when the isolators are subjected to tensile stresses, which arise under direct tensile actions or large shear strains. To analyze the influence of changes in the manufacturing process on the isolator adhesive behavior, the authors performed tensile tests on square-shaped small-scale specimens rather than expensive shear tests on full-scale isolators. Hence, the adhesion behavior between elastomer and steel layers was investigated through the tensile tests discussed herein. Among the influencing parameters that were considered, it was found that an increase in vulcanization time does not improve the adhesion, but it may actually worsen the capacity of the isolator in terms of strength. Moreover, it was found that using elastomer without an oily component improves the adhesion between the layers and increases the isolator’s dissipative capacity.

scholarly journals Experimental Research on Bond Behaviour of Fabric Reinforced Cementitious Matrix Composites for Retrofitting Masonry Walls

2021 ◽  
Vol 15 (1) ◽  
Author(s):  
Fayu Wang ◽  
Nicholas Kyriakides ◽  
Christis Chrysostomou ◽  
Eleftherios Eleftheriou ◽  
Renos Votsis ◽  
...  
Keyword(s):  
Large Scale ◽  
Tensile Tests ◽  
Seismic Resistance ◽  
Matrix Composites ◽  
Bond Behaviour ◽  
Cementitious Matrix ◽  
The Matrix ◽  
Rc Frame Buildings ◽  
Direct Tensile ◽  
Fabric Reinforced Cementitious Matrix

AbstractFabric reinforced cementitious matrix (FRCM) composites, also known as textile reinforced mortars (TRM), an inorganic matrix constituting fibre fabrics and cement-based mortar, are becoming a widely used composite material in Europe for upgrading the seismic resistance of existing reinforced concrete (RC) frame buildings. One way of providing seismic resistance upgrading is through the application of the proposed FRCM system on existing masonry infill walls to increase their stiffness and integrity. To examine the effectiveness of this application, the bond characteristics achieved between (a) the matrix and the masonry substrate and (b) the fabric and the matrix need to be determined. A series of experiments including 23 material performance tests, 15 direct tensile tests of dry fabric and composites, and 30 shear bond tests between the matrix and brick masonry, were carried out to investigate the fabric-to-matrix and matrix-to-substrate bond behaviour. In addition, different arrangements of extruded polystyrene (XPS) plates were applied to the FRCM to test the shear bond capacity of this insulation system when used on a large-scale wall.

scholarly journals Mechanical Properties of Spruce Wood Extracted from GLT Beams Loaded by Fire

2021 ◽  
Vol 13 (10) ◽  
pp. 5494
Author(s):  
Lucie Kucíková ◽  
Michal Šejnoha ◽  
Tomáš Janda ◽  
Jan Sýkora ◽  
Pavel Padevět ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Cross Section ◽  
Negative Impact ◽  
Tensile Tests ◽  
Thermal Recovery ◽  
Bending Test ◽  
Small Scale ◽  
Spruce Wood ◽  
The Impact

Heating wood to high temperature changes either temporarily or permanently its physical properties. This issue is addressed in the present contribution by examining the effect of high temperature on residual mechanical properties of spruce wood, grounding on the results of full-scale fire tests performed on GLT beams. Given these tests, a computational model was developed to provide through-thickness temperature profiles allowing for the estimation of a charring depth on the one hand and on the other hand assigning a particular temperature to each specimen used subsequently in small-scale tensile tests. The measured Young’s moduli and tensile strengths were accompanied by the results from three-point bending test carried out on two groups of beams exposed to fire of a variable duration and differing in the width of the cross-section, b=100 mm (Group 1) and b=160 mm (Group 2). As expected, increasing the fire duration and reducing the initial beam cross-section reduces the residual bending strength. A negative impact of high temperature on residual strength has also been observed from simple tensile tests, although limited to a very narrow layer adjacent to the charring front not even exceeding a typically adopted value of the zero-strength layer d0=7 mm. On the contrary, the impact on stiffness is relatively mild supporting the thermal recovery property of wood.

scholarly journals Tensile Behaviour of FRCM Composites for Strengthening of Masonry Structures—An Experimental Investigation

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3626
Author(s):  
Łukasz Hojdys ◽  
Piotr Krajewski
Keyword(s):  
Tensile Stress ◽  
Strain Curve ◽  
Tensile Tests ◽  
Tensile Failure ◽  
Tensile Behaviour ◽  
Masonry Structures ◽  
Stress Strain ◽  
Flexural Tensile Strength ◽  
Cracking Pattern ◽  
Direct Tensile

This paper presents the results of direct tensile tests performed on six different FRCM (fabric reinforced cementitious matrix) strengthening systems used for masonry structures. The emphasis was placed on the determination of the mechanical parameters of each tested system and a comparison of their tensile behaviour in terms of first crack stress, ultimate stress, ultimate strain, cracking pattern, failure mode and idealised tensile stress-strain curve. In addition to the basic mechanical tensile parameters, accidental load eccentricities, matrix tensile strengths, and matrix modules of elasticity were estimated. The results of the tests showed that the tensile behaviour of FRCM composites strongly depends on the parameters of the constituent materials (matrix and fabric). In the tests, tensile failure of reinforcement and fibre slippage within the matrix were observed. The presented research showed that the accidental eccentricities did not substantially affect the obtained results and that the more slender the specimen used, the more consistent the obtained results. The analysis based on a rule of mixtures showed that the direct tensile to flexural tensile strength ratio of the matrixes used in the test was 0.2 to 0.4. Finally, the tensile stress–strain relationship for the tested FRCMs was idealised by a bi- or tri-linear curve.

Evaluation of Tensile Properties Profile of Weld Zone Using Instrumented Indentation

2010 ◽  
Author(s):  
Seung-Kyun Kang ◽  
Young-Cheon Kim ◽  
Chan-Pyoung Park ◽  
Dongil Kwon
Keyword(s):  
Tensile Properties ◽  
Weld Zone ◽  
Indentation Test ◽  
Tensile Tests ◽  
Structural Safety ◽  
Small Scale ◽  
Stress And Strain ◽  
Instrumented Indentation ◽  
Deformation And Fracture ◽  
Instrumented Indentation Test

Understanding the property distribution in the weld zone is very important for structural safety, since deformation and fracture begin at the weakest point. However, conventional tensile tests can measure only average material properties because they require large specimens. Small-scale tests are being extensively researched to remove this limitation, among such tests, instrumented indentation test (IIT) are of great interest because of their simple procedures. Here we describe the evaluation of tensile properties using IIT and a representative stress-strain approach. The representative stressstrain method, introduced in 2008 in ISO/TR29381, directly correlates the stress and strain under the indenter to the true stress and strain of tensile testing by defining representative functions. Using this technique, we successfully estimate the yield strength and tensile strength of structural metallic materials and also obtain profiles of the weld-zone tensile properties.

Performance of All-Polypropylene Composites at LNG Temperatures

2017 ◽  
Author(s):  
Bilim Atli-Veltin
Keyword(s):  
Composite Materials ◽  
Mechanical Performance ◽  
Cost Effective ◽  
Tensile Tests ◽  
Small Scale ◽  
Failure Behavior ◽  
Polypropylene Composites ◽  
Design Flexibility ◽  
Static Tensile ◽  
Interlaminar Shear

In the small scale LNG infrastructure, composite materials are scarcely employed. Potentially, cost effective solutions for LNG applications could be developed thanks to the advantages of composite materials over metals such as weight savings, design flexibility and recyclability. The research presented in this paper focuses on the mechanical performance of fully recyclable, thermoplastic Polypropylene (PP) composite tapes at cryogenic LNG temperatures. Quasi-static tensile tests performed on [±45] laminates made of plain woven plies of PURE® show that at −196°C the behavior is bilinear with the failure strain of 6.5% and failure stress of 37 MPa. Such non-brittle failure behavior of PP is desirable for cryogenic applications. The other results presented in the paper contains [0/90] laminate results and the interlaminar shear strength characteristics at room and cryogenic temperatures.

scholarly journals Cyclic and Permanent Shear Strains of a Soft Cohesive Soil Subjected to Combined Static and Cyclic Loading

2020 ◽  
Vol 10 (23) ◽  
pp. 8433
Author(s):  
Hernán Patiño ◽  
Rubén Galindo ◽  
Claudio Olalla Marañón
Keyword(s):  
Simple Shear ◽  
Cohesive Soil ◽  
Mediterranean Coast ◽  
Vertical Stress ◽  
Experimental Program ◽  
Shear Stresses ◽  
Shear Tests ◽  
Cyclic Shear ◽  
Shear Strains ◽  
Number Of Cycles

This paper refers to cyclic shear strains (γc) and permanent shear strains (γp) of a soft cohesive soil, when both monotonic shear stresses (τo) and cyclic shear stresses (τc) are applied. The research is backed by an extensive experimental program with 139 cyclic simple shear tests that included identification and classification tests. These cyclic simple shear tests were conducted under different levels of stresses, τo, before the cyclic phase. Laboratory tests were carried out on undisturbed samples from the Port of Barcelona, located in Spain on the Mediterranean coast, and characterized by a monotonic strength (τmax) approximately equal to 30% of the initial effective vertical stress (σ′ov). The samples were taken at depths between 29 and 52 m and correspond to an initial effective vertical stress between 277 and 413 kPa, respectively. In general, the results indicate that: (a) the combination of τo and τc controls the generation of γc and γp, (b) it is not always true that when τo/σ′ov + τc/σ′ov ≈ τmax/σ′ov, the soil reaches failure cyclically, and (c) empirical relations useful for design can be established between γc, γp, and the number of cycles (N), for different relationships varying (τo/σ′ov) between 0% and 25%.

Influence of Alkaline Environments on the Mechanical Properties of FRCM/CRM and their Materials

2019 ◽  
Vol 817 ◽  
pp. 195-201
Author(s):  
Valeria Rizzo ◽  
Antonio Bonati ◽  
Francesco Micelli ◽  
Marianovella Leone ◽  
Maria Antonietta Aiello
Keyword(s):  
Glass Fibers ◽  
Tensile Tests ◽  
Design Guidelines ◽  
Hydraulic Lime ◽  
System A ◽  
Reinforced Polymer ◽  
Fiber Reinforced Polymer Composites ◽  
Alkaline Environments ◽  
Externally Bonded ◽  
Direct Tensile

Fabric Reinforced Mortar (FRCM) used as Externally Bonded Reinforcements (EBR), provide a sustainable solution for retrofitting and repair of existing masonry structures. They are commonly made by fibrous meshes embedded in a cementitious/hydraulic lime matrix. This technique represents a valid alternative to the well-known FRP (Fiber Reinforced Polymer) composites, which show some limitations in heritage masonry applications. In this scenario, a new system known as CRM (Composite Reinforced Mortar) has been developed in the last years. In this system, a pre-cured FRP grid is utilized as internal reinforcement in a mortar layer. The system reproduces the traditional technique of reinforced plaster, where the steel grid is substituted by a non-metallic one. In masonry applications high compatibility with the substrate, sustainability and removability are commonly required in heritage construction. These goals are not easily achieved by using fibers immersed into a polymeric resin. Moreover, the inorganic matrix ensures the transpiration of substrates and consequently a higher durability of the whole strengthened system is expected. On the other hand, the recent use of these new materials in civil engineering needs appropriate design guidelines. The proposed paper focuses attention on the initial results of a large experimental study on the durability of FRCM/CRM systems and their single components (dry glass fibers, resin, pre-cured FRP grid and mortar). In particular, the influence of three alkaline environments solutions was studied. Exposure conditions were stressed by increasing the temperature of the three aqueous solutions. The mechanical retention of tensile properties was measured by performing direct tensile tests after different exposure times.

Drift of Piles Subjected to Cyclic Lateral Loading From a Varying Direction: System vs. Soil Element Behavior

2014 ◽  
Author(s):  
Christina Rudolph ◽  
Jürgen Grabe ◽  
Britta Bienen
Keyword(s):  
Cyclic Loading ◽  
Model Tests ◽  
Small Scale ◽  
Shear Tests ◽  
Centrifuge Testing ◽  
Scale Modeling ◽  
Highly Sensitive ◽  
Number Of Cycles ◽  
Laterally Loaded ◽  
Insight Into

Offshore monopiles are usually designed using the p-y method for cyclic loading. While the method works for static loading, it was not developed for high numbers of cycles. Since the turbines are highly sensitive towards tilting, cyclic loading must be considered. The static results should therefore be combined with results from cyclic model tests with a high number of cycles to account for the accumulation of displacement or rotation during the lifetime of these structures. These model tests can underestimate the accumulation, however, as it has recently been shown that a change of loading direction can increase the accumulation considerably. These results have been verified using small scale modeling and centrifuge testing. The results from modeling the full problem of a laterally loaded pile are compared here with results from cyclic simple shear tests with a change of shearing direction during the cyclic loading. For these tests, a newly developed apparatus is used. This allows further insight into the question how a soil can “retain a memory” of its loading history.

scholarly journals Using Post-Harvest Waste to Improve Shearing Behaviour of Loess and Its Validation by Multiscale Direct Shear Tests

2019 ◽  
Vol 9 (23) ◽  
pp. 5206 ◽  
Author(s):  
Wen-Chieh Cheng ◽  
Zhong-Fei Xue ◽  
Lin Wang ◽  
Jian Xu
Keyword(s):  
Shear Stress ◽  
Shear Strength ◽  
Strain Hardening ◽  
Gradual Increase ◽  
Small Scale ◽  
Optimal Dosage ◽  
Direct Shear ◽  
Shear Tests ◽  
Post Harvest ◽  
Direct Shear Tests

Loess and PHW (post-harvest waste) are easily accessible in the Chinese Loess Plateau and have been widely applied to construction of residential houses that have been inhabited for decades under the effect of freeze-thaw cycles. Although many researchers have recognised that the addition of fibers to loess soil is effective in preventing soil erosion and stabilising slopes, a consensus on this claim has not been reached yet. This study investigates the shearing behaviour of the loess-PHW mixture using small-scale and large-scale direct shear (SSDS and LSDS) tests. Four typical shear stress versus horizontal displacement curves from the multiscale direct shear tests are recognised where one is featured with strain-softening shape and the other three with a strain-hardening shape. Two out of the three curves with strain-hardening shape show a gradual increase in the shear stress at additional and larger displacements, respectively, in which some factor starts to have an influence on the shearing behaviour. Comparisons of the shear strength measured in SSDS and LSDS are made, indicating that there are differences between SSDS and LSDS. The effect of PHW addition on shear strength is assessed in order to determine the optimal dosage. The improvement of shear strength is attributed to the effect of particle inter-locking, resulting from the addition of PHW to loess specimens, and takes effect as the water content surpassed a threshold, i.e., >14%, that facilitates particle rearrangement. Particle-box interaction behaviour is assessed at the same time, and the findings satisfactorily address the main cause of the gradual increase in shear stress following the curve inflection point. The improved shearing behaviour proves the ability of the loess-PHW mixture to resist the seepage force and consequently stratum erosion.

Sign in / Sign up

Export Citation Format

Share Document