scholarly journals Integrated Geothermal Energy Systems for Small-Scale Combined Heat and Power Production: Energy and Economic Investigation

2020 ◽  
Vol 10 (19) ◽  
pp. 6639 ◽  
Author(s):  
Pietropaolo Morrone ◽  
Angelo Algieri
Keyword(s):  
Geothermal Energy ◽  
Energy Demand ◽  
High Efficiency ◽  
Energy Performance ◽  
Combined Heat And Power ◽  
Integrated System ◽  
Operating Conditions ◽  
Economic Viability ◽  
Small Scale ◽  
Partial Load

In recent years, an increasing interest in geothermal energy has been registered in both the scientific community and industry. The present work aims to analyse the energy performance and the economic viability of an innovative high-efficiency geothermal-driven integrated system for a combined heat and power (CHP) application. The system consists of a heat exchanger (HEX) and a transcritical organic Rankine cycle (ORC) that work in parallel to exploit a high-temperature geothermal source (230 °C) and satisfy the energy demand of a commercial centre located in Southern Italy. The ORC and HEX sub-units can operate at partial load to increase the system flexibility and to properly react to continuous changes in energy request. A lumped model was developed to find the proper operating conditions and to evaluate the energy production on an hourly basis over the whole year. In particular, a multi-variable optimisation was implemented to find the most suitable configuration and a 101.4 kWel ORC was selected while the HEX nominal power was 249.5 kWth. The economic viability of the integrated system was evaluated in terms of net present value and payback period and different operating strategies were compared: thermal-driven, electric-driven, and a mixed strategy. The latter turned out to be the best solution according to both energy and economic criteria, with electric and thermal self-consumptions larger than 90%, with no heat dumping and a payback time close to five years.

Data-Driven Predesign Tool for Small-Scale Centrifugal Compressor in Refrigeration

2018 ◽  
Vol 140 (12) ◽  
Author(s):  
Mounier Violette ◽  
Picard Cyril ◽  
Schiffmann Jürg
Keyword(s):  
Centrifugal Compressor ◽  
High Efficiency ◽  
Design Procedure ◽  
Integrated System ◽  
Operating Conditions ◽  
Data Driven ◽  
Small Scale ◽  
Centrifugal Compressors ◽  
Starting Point ◽  
Isentropic Efficiency

Domestic scale heat pumps and air conditioners are mainly driven by volumetric compressors. Yet the use of reduced scale centrifugal compressors is reconsidered due to their high efficiency and power density. The design procedure of centrifugal compressors starts with predesign tools based on the Cordier line. However, the optimality of the obtained predesign, which is the starting point of a complex and iterative process, is not guaranteed, especially for small-scale compressors operating with refrigerants. This paper proposes a data-driven predesign tool tailored for small-scale centrifugal compressors used in refrigeration applications. The predesign model is generated using an experimentally validated one-dimensional (1D) code which evaluates the compressor performance as a function of its detailed geometry and operating conditions. Using a symbolic regression tool, a reduced order model that predicts the performance of a given compressor geometry has been built. The proposed predesign model offers an alternative to the existing tools by providing a higher level of detail and flexibility. Particularly, the model includes the effect of the pressure ratio, the blade height ratio, and the shroud to tip radius ratio. The analysis of the centrifugal compressor losses allows identifying the underlying phenomena that shape the new isentropic efficiency contours. Compared to the validated 1D code, the new predesign model yields deviations below 4% on the isentropic efficiency, while running 1500 times faster. The new predesign model is, therefore, of significant interest when the compressor is part of an integrated system design process.

scholarly journals The Operating Strategies of Small-Scale Combined Heat and Power Plants in Liberalized Power Markets

Energies ◽  
2018 ◽  
Vol 11 (11) ◽  
pp. 3110 ◽  
Author(s):  
Pavel Atănăsoae
Keyword(s):  
Electricity Markets ◽  
Electricity Market ◽  
Power Plants ◽  
High Efficiency ◽  
Organic Rankine Cycle ◽  
Combined Heat And Power ◽  
Operating Conditions ◽  
Power Markets ◽  
Small Scale ◽  
Operating Strategies

Distributed generation is a good option for future energy systems with respect to sustainable development. In this context, the small-scale combined heat and power (CHP) plants are seen as an efficient way to reduce greenhouse gas emissions due to lower fuel consumption compared to the separate generation of the heat and electricity. The objective of this paper is to establish operating strategies of the small-scale CHP plants to reduce operational cost and increase revenue in liberalized electricity markets. It analyzes a cogeneration plant with organic Rankine cycle and biomass fuel under the conditions of the Romanian electricity market and the green certificates support scheme for electricity generated in high efficiency cogeneration and from renewable sources. The main finding is that choosing an appropriate mode of operation and using correlated prices of heat and electricity can increase the trading profitability of a CHP plant in liberalized power markets. This can be done by an analysis of the particularities and the specific operating conditions of the CHP plant. The results show that the operating strategies of the CHP plant can yield substantial net revenues from electricity and heat sales. The CHP plant can be economically operated to a useful heat load of more than 40% when operating strategies are applied.

scholarly journals Improvement Effect of Green Remodeling and Building Value Assessment Criteria for Aging Public Buildings

Energies ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 1200
Author(s):  
Yong-Joon Jun ◽  
Seung-ho Ahn ◽  
Kyung-Soon Park
Keyword(s):  
High Efficiency ◽  
Energy Performance ◽  
Operating Conditions ◽  
Energy Usage ◽  
Public Buildings ◽  
Value Judgment ◽  
Relationship Analysis ◽  
Improvement Effect ◽  
The Relationship ◽  
Usage Data

The Green Remodeling Project under South Korea’s Green New Deal policy is a government-led project intended to strengthen the performance sector directly correlated with energy performance among various elements of improvement applicable to building remodeling by replacing insulation materials, introducing new and renewable energy, introducing high-efficiency equipment, etc., with public buildings taking the lead in green remodeling in order to induce energy efficiency enhancement in private buildings. However, there is an ongoing policy that involves the application of a fragmentary value judgment criterion, i.e., whether to apply technical elements confined to the enhancement of the energy performance of target buildings and the prediction of improvement effects according thereto, thus resulting in the phenomenon of another important value criterion for green remodeling, i.e., the enhancement of the occupant (user) comfort performance of target buildings as one of its purposes, being neglected instead. In order to accurately grasp the current status of these problems and to promote ‘expansion of the value judgment criteria for green remodeling’ as an alternative, this study collected energy usage data of buildings actually used by public institutions and then conducted a total analysis. After that, the characteristics of energy usage were analyzed for each of the groups of buildings classified by year of completion, thereby carrying out an analysis of the correlation between the non-architectural elements affecting the actual energy usage and the actual energy usage data. The correlation between the improvement performance of each technical element and the actual improvement effect was also analyzed, thereby ascertaining the relationship between the direction of major policy strategies and the actual energy usage. As a result of the relationship analysis, it was confirmed that the actual energy usage is more affected by the operating conditions of the relevant building than the application of individual strategic elements such as the performance of the envelope insulation and the performance of the high-efficiency system. In addition, it was also confirmed that the usage of public buildings does not increase in proportion to their aging. The primary goal of reducing energy usage in target buildings can be achieved if public sector (government)-led green remodeling is pushed ahead with in accordance with biased value judgment criteria, just as in the case of a campaign to refrain from operating cooling facilities in aging public buildings. However, it was possible to grasp through the progress of this study that the remodeling may also result in the deterioration of environmental comfort and stability, such as the numerical value of the indoor thermal environment. The results of this study have the significance of providing basic data for pushing ahead with a green remodeling policy in which the value judgment criteria for aging existing public buildings are more expanded, and it is necessary to continue research in such a direction that the quantitative purpose of green remodeling, which is to reduce energy usage in aging public buildings, and its qualitative purpose, which is to enhance their environmental performance for occupants’ comfort, can be mutually balanced and secured at the same time.

Three Spool High Efficiency Small Scale Gas Turbine Concept

2017 ◽  
Author(s):  
Matti Malkamäki ◽  
Ahti Jaatinen-Värri ◽  
Antti Uusitalo ◽  
Aki Grönman ◽  
Juha Honkatukia ◽  
...  
Keyword(s):  
Power Generation ◽  
Gas Turbine ◽  
Gas Turbines ◽  
High Efficiency ◽  
Small Scale ◽  
Inlet Temperature ◽  
Substantial Impact ◽  
Electrical Efficiency ◽  
Partial Load ◽  
Reciprocating Engines

Decentralized electricity and heat production is a rising trend in small-scale industry. There is a tendency towards more distributed power generation. The decentralized power generation is also pushed forward by the policymakers. Reciprocating engines and gas turbines have an essential role in the global decentralized energy markets and improvements in their electrical efficiency have a substantial impact from the environmental and economic viewpoints. This paper introduces an intercooled and recuperated three stage, three-shaft gas turbine concept in 850 kW electric output range. The gas turbine is optimized for a realistic combination of the turbomachinery efficiencies, the turbine inlet temperature, the compressor specific speeds, the recuperation rate and the pressure ratio. The new gas turbine design is a natural development of the earlier two-spool gas turbine construction and it competes with the efficiencies achieved both with similar size reciprocating engines and large industrial gas turbines used in heat and power generation all over the world and manufactured in large production series. This paper presents a small-scale gas turbine process, which has a simulated electrical efficiency of 48% as well as thermal efficiency of 51% and can compete with reciprocating engines in terms of electrical efficiency at nominal and partial load conditions.

scholarly journals A Novel Hybrid Technique of Frequency Control for Distributed Energy Resources

2021 ◽  
Vol 40 (1) ◽  
pp. 180-204
Author(s):  
Hasham Khan
Keyword(s):  
Power Distribution ◽  
Distribution System ◽  
Energy Demand ◽  
Frequency Control ◽  
Industrial Sector ◽  
Operating Conditions ◽  
Small Scale ◽  
Hybrid Technique ◽  
Operating Characteristics ◽  
Power Distribution System

The rapid increase in the population and fastest development in the industrial sector has increased the energy demand throughout the world. Frequent outages and load shedding has seriously deteriorated the efficiency of the electrical power distribution system. Under such circumstances, the implementation of Distributed Generation (DG) is increasing. Small hydel generators are considered as the most-clean and economical for generating electrical energy. These are very complex nonlinear generators which usually exhibits low frequency electromechanical oscillations due to insufficient damping caused by severe operating conditions. These DGs are not connected to the utility in many cases because, under varying load, they cannot maintain the frequency to the permissible value. This work presents detailed analysis of operating characteristics and proposes a hybrid frequency control strategy of the small hydel systems. The simulation and testing is performed in MATLAB, the results verified the improved performance with the recommended method. The proposed method conserves half of the power consumption. The control scheme regulates the dump load by connecting and disconnecting it affectively. The application of presented methodology is convenient in the deregulated environment, especially under the severe shortage of energy. The proposed model keeps the frequency of system at desired level. It reduces the noise, thereby improving the response time of the designed controller as compared to conventional controllers. The innovative scheme also provides power for small scale industrial, agricultural and other domestic application of far-off areas where the supply of utility main grid is difficult to provide. The recommended scheme is environmental friendly and easy to implement wherever small hydel resources are available.

scholarly journals Do Consumers Care about the Energy Efficiency of Buildings? Understanding Residential Choice Based on Energy Performance Certificates

2018 ◽  
Vol 10 (11) ◽  
pp. 4297 ◽  
Author(s):  
Hyunjoo Lee ◽  
Misuk Lee ◽  
Sesil Lim
Keyword(s):  
Energy Efficiency ◽  
Energy Demand ◽  
High Efficiency ◽  
Early Stage ◽  
Energy Performance ◽  
Price Premium ◽  
Consumer Decision Making ◽  
Residential Choice ◽  
Performance Information ◽  
The Government

Disclosing the energy performance information for buildings has been expected to become an important policy for controlling energy demand and reducing CO2 emissions, but its effectiveness remains controversial. This study investigates the effect of energy performance information on consumer residential choice by using a discrete choice experiment in South Korea. The estimation results confirmed that the energy efficiency level of the given housing has a significant effect on consumer residential choice when the related information is actually delivered. Combined with evidence from the simulation study, we suggest that obligating the owners to provide energy performance information to potential buyers/tenants would be necessary for enhancing the use of the information during the consumer decision-making process. Additionally, the simulation result implies that the effectiveness of the policy can be underestimated by the price premium related to energy efficiency. Therefore, we suggest that the government should control the price premium for high-efficiency buildings at the early stage so that the policy related to disclosing the energy performance can be on track.

Development and Optimization of a Small Scale Pellet Burner

2012 ◽  
Author(s):  
José Carlos Teixeira ◽  
Rui Ferreira ◽  
Eurico A. Seabra ◽  
Manuel Eduardo Ferreira
Keyword(s):  
Fossil Fuels ◽  
High Efficiency ◽  
Practical Interest ◽  
Direct Conversion ◽  
Industrial Applications ◽  
Operating Conditions ◽  
Small Scale ◽  
Cylindrical Shape ◽  
Load Range ◽  
Air Supply

Environmental concerns and the drive to reduce the dependence on petroleum brought the use of renewable energies to the forefront. Biomass appears as a very interesting alternative for direct conversion into heat. In this context, densified forms of biomass such as pellets are of great relevance because of their easy of use, high efficiency and low emissions. The practical interest in pellet combustion has been driven by the domestic heating sector, which favors the characteristics that are intrinsic of this fuel, despite its relatively higher price. However, the growing costs of fossil fuels have extended the interest of pellet fuels into industrial applications, including co-firing in power stations. A fast growing market includes the retrofitting of existing fuel boilers and furnaces with alternative burners that can be fitted into existing combustion systems. Such an approach has proved very attractive due to the low installation cost and the growing existence of fuels produced in the vicinity of the end user. This involves in most cases a custom built application which requires a high level of flexibility to variable operating conditions. This work reports on the development of a 120 kW pellet burner. A prototype of the burner was built that enables the independent control of the air supply into various regions of the combustion chamber and an accurate supply of fuel. The burner was fitted into a testing furnace of cylindrical shape oriented horizontally. Its diameter is 0.5 m and is constructed in a modular fashion with a total length of 2.2 m. All the facility is fully instrumented and includes: temperature data in various locations inside the chamber, flue gases emissions (CO, CO2, NOx) measurements and flow rates. The objective of the test and development is to optimize the combustion over the thermal load range of the facility. The excess air, fuel supply (primary and secondary) and the shape of the furnace grate enable the optimization of the burner with CO emissions of approximately 50 ppm, well below the acceptable limits.

Assessment of Tesla Turbine Performance for Small Scale Rankine Combined Heat and Power Systems

2010 ◽  
Vol 132 (12) ◽  
Author(s):  
Van P. Carey
Keyword(s):  
Power Systems ◽  
Residential Buildings ◽  
Rankine Cycle ◽  
Combined Heat And Power ◽  
Operating Conditions ◽  
Working Fluid ◽  
Small Scale ◽  
Manufacturing Cost ◽  
Turbine Design ◽  
The Impact

For solar Rankine cycle combined heat and power systems for residential buildings and other small-scale applications (producing 1–10 kWe), a low manufacturing cost, robust, and durable expander is especially attractive. The Tesla-type turbine design has these desired features. This paper summarizes a theoretical exploration of the performance of a Tesla turbine as the expander in a small-scale Rankine cycle combined heat and power system. A one-dimensional idealized model of momentum transfer in the turbine rotor is presented, which can be used to predict the efficiency of the turbine for typical conditions in these systems. The model adopts a nondimensional formulation that identifies the dimensionless parameters that dictate performance features of the turbine. The model is shown to agree well with experimental performance data obtained in earlier tests of prototype Tesla turbine units. The model is used to explore the performance of this type of turbine for Rankine cycle applications using water as a working fluid. The model indicates that isentropic efficiencies above 0.75 can be achieved if the operating conditions are tailored in an optimal way. The scalability of the turbine design, and the impact of the theoretical model predictions on the development of solar combined heat and power systems are also discussed.

scholarly journals Numerical Optimisation of The Diffuser In a Typical Turbocharger Compressor Using The Adjoint Method.

2021 ◽  
Author(s):  
Kristaq Hazizi ◽  
Ahad Ramezanpour ◽  
Aaron Costall
Keyword(s):  
High Efficiency ◽  
Numerical Models ◽  
A Priori ◽  
Central Area ◽  
Axial Flow ◽  
Operating Conditions ◽  
Complex Flow ◽  
Local Flow ◽  
Passenger Car ◽  
Partial Load

Abstract In the automotive industry, the demand for fuel economy and emission reduction has led to the downsizing of engines and turbochargers play a leading role in compensating for the performance loss. In complex flow modelling of the compressor, effective determination of the mesh resolution is not a priori due to variation of local flow and turbulence variables. In this study, the compressible flow of a centrifugal turbocharger compressor was numerically modelled. The accuracy of the models is discussed with respect to boundary layer adaptivity for the k-w SST turbulence model. The numerical models are investigated and verified against pick efficiency, extracted experimental points at 150,000 (rpm), along with other points of partial load at 80,000 (rpm) speed lines. The TD025-05T4 compressor of the 1.2 Litre engine Renault Megane passenger car was designed, constructed and provided experimental data (compressor map) by Mitsubishi Turbocharger and Engine Europe (MTEE). In addition, a numerical and mathematical study has been developed on the aerodynamic optimisation of the turbocharger compressor diffuser geometry. The optimisation of the single-target problem (efficiency) of the axial flow compressor outlet stage is carried out using a new smart evolutionary optimisation technique named adjoint solver. The Adjoint solver usually produces a surface vector field that shows how and where the geometry can be changed for optimisation based on a defined objective, efficiency in this study. Such irregular and non-parametric changes could be manufactured using recent advances in 3D printing technology.The expected result of optimisation of the diffuser geometry started with the design point, central area, 150,000 (rpm) speed line, shows a gradual development of efficiency to an uttermost of 2.5% and the process of optimisation has been enlarged and completed on all design operating areas selected previously. The development of an optimised geometry diffuser accomplishes a wider operating range, high efficiency and robust performance due to changes in engine operating conditions in the high-pressure area. Therefore, the optimal diffuser geometry leads to an impact on the engine’s efficiency and overall performance of a passenger car for real-world drive cycles, increasing power output and improving thermal efficiency.

scholarly journals Experimental Assessment of Energy Performance and Emissions of a Residential Microcogenerator

2014 ◽  
Vol 1 (2) ◽  
pp. 48 ◽  
Author(s):  
Giovanni Angrisani ◽  
Carlo Roselli ◽  
Maurizio Sasso ◽  
Peter Tzscheutschler
Keyword(s):  
Energy Saving ◽  
High Efficiency ◽  
Thermal Power ◽  
Experimental Tests ◽  
Energy Performance ◽  
Primary Energy ◽  
Economic Feasibility ◽  
Operating Conditions ◽  
Hot Water ◽  
Test Facility

Microcogeneration can guarantee sensible primary energy savings and greenhouse gas emissions reductions in the residential sector. In this paper, the results of experimental tests carried out on a microcogenerator (5.5 kW electric power and 14.8 kW thermal power) based on a natural gas fuelled internal combustion engine, integrated with a condensing boiler, have been analyzed. Tests have been performed out at Institute for Energy Economy and Application Technology (IfE) of Technical University of Munich (Germany). The test facility allowed to simulate the thermal energy requirements of a real residential application, represented by a Multi Family House consisting of 10 apartments, and to evaluate the energy flows of the conversion devices in actual operating conditions. Four type days, characteristic of Mediterranean climatic conditions, have been used to define space heating and domestic hot water user’s requirements. Experimental tests have been performed to implement energy and environmental analysis, comparing the system consisting of cogenerator and integration boiler with a reference system. Results showed that the former can achieve a primary energy saving of about 6%, and CO2 equivalent emissions reduction of about 12%. Finally, the algorithm defined by the European Directive on the promotion of high efficiency cogeneration has been implemented; it demonstrated that the primary energy saving is well above the limit value prescribed by the Directive. Therefore the cogeneration plant can access support mechanisms that can help to achieve the economic feasibility of the system, besides energy and environmental benefits.

Sign in / Sign up

Export Citation Format

Share Document