scholarly journals Rubber Dam Isolation and High-Volume Suction Reduce Ultrafine Dental Aerosol Particles: An Experiment in a Simulated Patient

2020 ◽  
Vol 10 (18) ◽  
pp. 6345
Author(s):  
Julián Balanta-Melo ◽  
Albio Gutiérrez ◽  
Gustavo Sinisterra ◽  
María del Mar Díaz-Posso ◽  
David Gallego ◽  
...  
Keyword(s):  
Volume Fraction ◽  
Aerosol Particles ◽  
High Volume ◽  
Simulated Patient ◽  
Volume Distribution ◽  
Risk Of Infection ◽  
Dental Services ◽  
Total Particulate Matter ◽  
Rubber Dam ◽  
Average Size

The ongoing Coronavirus Disease 2019 (COVID-19) pandemic has triggered the paralysis of dental services ascribed to the potential spread of severe acute respiratory syndrome (SARS)-CoV-2. Aerosol-generating procedures (AGPs) are common in dentistry, which in turn increase the risk of infection of the dental personnel due to the salivary presence of SARS-CoV-2 in COVID-19 patients. The use of rubber dam isolation (RDI) and high-volume evacuators (HVE) during AGPs is recommended to control dental aerosols, but the evidence about their effectiveness is scarce. This first study aimed to compare, in a simulated patient, the effectiveness of the following strategies: standard suction (SS), RDI and RDI + HVE. Using the laser diffraction technique, the effect of each condition on the volume distribution, average size and concentration of coarse (PM10), fine (PM2.5) and ultrafine (PM0.1) particles were evaluated. During the teeth drilling, the highest volume fraction of dental aerosol particles with SS was below 1 μm of aerodynamic diameter. Additionally, the RDI + HVE significantly reduced both the ultrafine dental aerosol particles and the concentration of total particulate matter. AGPs represent a potential risk for airborne infections in dentistry. Taken together, these preliminary results suggest that isolation and high-volume suction are effective to reduce ultrafine dental aerosol particles.

Morphology, Distribution and Identification of Micro-Constituents Along Grain Boundaries in Nickel-Base Alloys

1973 ◽  
Vol 31 ◽  
pp. 176-177
Author(s):  
D. E. Fornwalt ◽  
A. R. Geary ◽  
B. H. Kear
Keyword(s):  
Electron Microscope ◽  
Grain Boundaries ◽  
Volume Fraction ◽  
Rupture Life ◽  
Stress Rupture ◽  
High Volume ◽  
Precipitate Morphology ◽  
Stress Rupture Life ◽  
Nickel Base ◽  
Scanning Electron

A systematic study has been made of the effects of various heat treatments on the microstructures of several experimental high volume fraction γ’ precipitation hardened nickel-base alloys, after doping with ∼2 w/o Hf so as to improve the stress rupture life and ductility. The most significant microstructural chan§e brought about by prolonged aging at temperatures in the range 1600°-1900°F was the decoration of grain boundaries with precipitate particles.Precipitation along the grain boundaries was first detected by optical microscopy, but it was necessary to use the scanning electron microscope to reveal the details of the precipitate morphology. Figure 1(a) shows the grain boundary precipitates in relief, after partial dissolution of the surrounding γ + γ’ matrix.

Grain Refinement in Titanium-Erbium Alloys

1974 ◽  
Vol 32 ◽  
pp. 522-523
Author(s):  
B. B. Rath ◽  
J. E. O'Neal ◽  
R. J. Lederich
Keyword(s):  
Electron Microscopy ◽  
Size Distribution ◽  
Grain Refinement ◽  
Grain Growth ◽  
Volume Fraction ◽  
Pure Titanium ◽  
Systematic Investigation ◽  
Second Phase ◽  
Titanium Matrix ◽  
Average Size

Addition of small amounts of erbium has a profound effect on recrystallization and grain growth in titanium. Erbium, because of its negligible solubility in titanium, precipitates in the titanium matrix as a finely dispersed second phase. The presence of this phase, depending on its average size, distribution, and volume fraction in titanium, strongly inhibits the migration of grain boundaries during recrystallization and grain growth, and thus produces ultimate grains of sub-micrometer dimensions. A systematic investigation has been conducted to study the isothermal grain growth in electrolytically pure titanium and titanium-erbium alloys (Er concentration ranging from 0-0.3 at.%) over the temperature range of 450 to 850°C by electron microscopy.

HOT CORROSION OF CERIA-YTTRIA STABILIZED ZIRCONIA PLASMA SPRAYED THERMAL BARRIER COATING BY EUTECTIC VANDIUM PENTAOXIDE-SODIUM SULFATE

2018 ◽  
Vol 18 (1) ◽  
pp. 182-192 ◽  
Author(s):  
Mohammed J Kadhim ◽  
Mohammed H Hafiz ◽  
Maryam A Ali Bash
Keyword(s):  
Thermal Barrier Coating ◽  
Hot Corrosion ◽  
Monoclinic Phase ◽  
Volume Fraction ◽  
High Volume ◽  
Thermal Barrier ◽  
Air Plasma ◽  
Plan View ◽  
Barrier Coating ◽  
Plasma Sprayed

The high temperature corrosion behavior of thermal barrier coating (TBC) systemconsisting of IN-738 LC superalloy substrate, air plasma sprayed Ni24.5Cr6Al0.4Y (wt%)bond coat and air plasma sprayed ZrO2-20 wt% ceria-3.6 wt% yttria (CYSZ) ceramic coatwere characterized. The upper surfaces of CYSZ covered with 30 mg/cm2 , mixed 45 wt%Na2SO4-55 wt% V2O5 salt were exposed at different temperatures from 800 to 1000 oC andinteraction times from 1 up to 8 h. The upper surface plan view of the coatings wereidentified for topography, roughness, chemical composition, phases and reaction productsusing scanning electron microscopy, energy dispersive spectroscopy, talysurf, and X-raydiffraction. XRD analyses of the plasma sprayed coatings after hot corrosion confirmed thephase transformation of nontransformable tetragonal (t') into monoclinic phase, presence ofYVO4 and CeVO4 products. Analysis of the hot corrosion CYSZ coating confirmed theformation of high volume fraction of YVO4, with low volume fractions of CeOV4 and CeO2.The formation of these compounds were combined with formation of monoclinic phase (m)from transformation of nontransformable tetragonal phase (t').

scholarly journals Face Grinding Surface Quality of High Volume Fraction SiCp/Al Composite Materials

2021 ◽  
Vol 34 (1) ◽  
Author(s):  
Xu Zhao ◽  
Yadong Gong ◽  
Guiqiang Liang ◽  
Ming Cai ◽  
Bing Han
Keyword(s):  
Friction Coefficient ◽  
Surface Morphology ◽  
Surface Quality ◽  
Volume Fraction ◽  
High Volume ◽  
Spindle Speed ◽  
High Volume Fraction ◽  
Machining Parameters ◽  
Al Composite

AbstractThe existing research on SiCp/Al composite machining mainly focuses on the machining parameters or surface morphology. However, the surface quality of SiCp/Al composites with a high volume fraction has not been extensively studied. In this study, 32 SiCp/Al specimens with a high volume fraction were prepared and their machining parameters measured. The surface quality of the specimens was then tested and the effect of the grinding parameters on the surface quality was analyzed. The grinding quality of the composite specimens was comprehensively analyzed taking the grinding force, friction coefficient, and roughness parameters as the evaluation standards. The best grinding parameters were obtained by analyzing the surface morphology. The results show that, a higher spindle speed should be chosen to obtain a better surface quality. The final surface quality is related to the friction coefficient, surface roughness, and fragmentation degree as well as the quantity and distribution of the defects. Lower feeding amount, lower grinding depth and appropriately higher spindle speed should be chosen to obtain better surface quality. Lower feeding amount, higher grinding depth and spindle speed should be chosen to balance grind efficiently and surface quality. This study proposes a systematic evaluation method, which can be used to guide the machining of SiCp/Al composites with a high volume fraction.

scholarly journals Study on the High-Speed Milling Performance of High-Volume Fraction SiCp/Al Composites

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4143
Author(s):  
Youzheng Cui ◽  
Shenrou Gao ◽  
Fengjuan Wang ◽  
Qingming Hu ◽  
Cheng Xu ◽  
...  
Keyword(s):  
High Speed ◽  
Large Scale ◽  
Volume Fraction ◽  
Simulation Analysis ◽  
Cutting Temperature ◽  
High Volume ◽  
Cutting Parameters ◽  
High Volume Fraction ◽  
High Wear Resistance ◽  
Element Analysis

Compared with other materials, high-volume fraction aluminum-based silicon carbide composites (hereinafter referred to as SiCp/Al) have many advantages, including high strength, small change in the expansion coefficient due to temperature, high wear resistance, high corrosion resistance, high fatigue resistance, low density, good dimensional stability, and thermal conductivity. SiCp/Al composites have been widely used in aerospace, ordnance, transportation service, precision instruments, and in many other fields. In this study, the ABAQUS/explicit large-scale finite element analysis platform was used to simulate the milling process of SiCp/Al composites. By changing the parameters of the tool angle, milling depth, and milling speed, the influence of these parameters on the cutting force, cutting temperature, cutting stress, and cutting chips was studied. Optimization of the parameters was based on the above change rules to obtain the best processing combination of parameters. Then, the causes of surface machining defects, such as deep pits, shallow pits, and bulges, were simulated and discussed. Finally, the best cutting parameters obtained through simulation analysis was the tool rake angle γ0 = 5°, tool clearance angle α0 = 5°, corner radius r = 0.4 mm, milling depth ap = 50 mm, and milling speed vc= 300 m/min. The optimal combination of milling parameters provides a theoretical basis for subsequent cutting.

scholarly journals Effects of Polydispersity on the Phase Behavior of Additive Hard Spheres in Solution

Molecules ◽  
2021 ◽  
Vol 26 (6) ◽  
pp. 1543
Author(s):  
Luka Sturtewagen ◽  
Erik van der Linden
Keyword(s):  
Phase Behavior ◽  
Critical Point ◽  
Volume Fraction ◽  
Hard Spheres ◽  
Second Virial Coefficient ◽  
Two Phase ◽  
Different Types ◽  
Asymmetric Partitioning ◽  
Average Size ◽  
Liquid Liquid Phase Separation

The ability to separate enzymes, nucleic acids, cells, and viruses is an important asset in life sciences. This can be realised by using their spontaneous asymmetric partitioning over two macromolecular aqueous phases in equilibrium with one another. Such phases can already form while mixing two different types of macromolecules in water. We investigate the effect of polydispersity of the macromolecules on the two-phase formation. We study theoretically the phase behavior of a model polydisperse system: an asymmetric binary mixture of hard spheres, of which the smaller component is monodisperse and the larger component is polydisperse. The interactions are modelled in terms of the second virial coefficient and are assumed to be additive hard sphere interactions. The polydisperse component is subdivided into sub-components and has an average size ten times the size of the monodisperse component. We calculate the theoretical liquid–liquid phase separation boundary (the binodal), the critical point, and the spinodal. We vary the distribution of the polydisperse component in terms of skewness, modality, polydispersity, and number of sub-components. We compare the phase behavior of the polydisperse mixtures with their concomittant monodisperse mixtures. We find that the largest species in the larger (polydisperse) component causes the largest shift in the position of the phase boundary, critical point, and spinodal compared to the binary monodisperse binary mixtures. The polydisperse component also shows fractionation. The smaller species of the polydisperse component favor the phase enriched in the smaller component. This phase also has a higher-volume fraction compared to the monodisperse mixture.

scholarly journals Calibration of LACIS as a CCN detector and its use in measuring activation and hygroscopic growth of atmospheric aerosol particles

2006 ◽  
Vol 6 (12) ◽  
pp. 4519-4527 ◽  
Author(s):  
H. Wex ◽  
A. Kiselev ◽  
M. Ziese ◽  
F. Stratmann
Keyword(s):  
Sodium Chloride ◽  
Wall Temperature ◽  
Atmospheric Aerosol ◽  
Volume Fraction ◽  
Cloud Condensation Nuclei ◽  
Aerosol Particles ◽  
Urban Aerosol ◽  
Hygroscopic Growth ◽  
Atmospheric Aerosol Particles ◽  
Droplet Activation

Abstract. A calibration for LACIS (Leipzig Aerosol Cloud Interaction Simulator) for its use as a CCN (cloud condensation nuclei) detector has been developed. For this purpose, sodium chloride and ammonium sulfate particles of known sizes were generated and their grown sizes were detected at the LACIS outlet. From these signals, the effective critical super-saturation was derived as a function of the LACIS wall temperature. With this, LACIS is calibrated for its use as a CCN detector. The applicability of LACIS for measurements of the droplet activation, and also of the hygroscopic growth of atmospheric aerosol particles was tested. The activation of the urban aerosol particles used in the measurements was found to occur at a critical super-saturation of 0.46% for particles with a dry diameter of 75 nm, and at 0.42% for 85 nm, respectively. Hygroscopic growth was measured for atmospheric aerosol particles with dry diameters of 150, 300 and 350 nm at relative humidities of 98 and 99%, and it was found that the larger dry particles contained a larger soluble volume fraction of about 0.85, compared to about 0.6 for the 150 nm particles.

Sign in / Sign up

Export Citation Format

Share Document