scholarly journals Theoretical Design of a Novel Vibration Energy Absorbing Mechanism for Cables

2020 ◽  
Vol 10 (15) ◽  
pp. 5309
Author(s):  
Zhen Qin ◽  
Yu-Ting Wu ◽  
Aihua Huang ◽  
Sung-Ki Lyu ◽  
John W. Sutherland
Keyword(s):  
Vibration Isolation ◽  
Harmonic Balance Method ◽  
Hydraulic Cylinder ◽  
Vibration Energy ◽  
Single Degree Of Freedom ◽  
Environmental Vibration ◽  
Energy Absorbing ◽  
Vibration Isolation Performance ◽  
Isolation Performance ◽  
Novel Design

A novel design of a vibration energy absorbing mechanism (VEAM) that is based on multi-physics (magnetic spring, hydraulic system, structural dynamics, etc.) for cable vibration is proposed. The minimum working force of the hydraulic cylinder has been exploited in this design in order to combine a non-linear stiffness vibration isolation module that is composed of permanent magnetic springs with hydraulic viscous vibration damping modules. In response to different environmental vibration impacts, VEAM can automatically switch the vibration control modes without an electronic mechanism. Additionally, the non-contact design effectively reduces the wear that is induced by the reciprocating motion of the small amplitude of the hydraulic viscous dampers. The proposed mechanism is explained and a theoretical model is established. The transmissibility of the two modules at a single degree of freedom is derived using the harmonic balance method. After that, a series of variable control numerical simulations were performed for each important parameter. Empirical rules for designing the system were created by comparing the influence of each parameter on the vibration isolation performance of the entire system.

Vibration isolation performance of nonobstructive particle damping in a machine rack

2018 ◽  
Vol 25 (5) ◽  
pp. 1122-1130 ◽  
Author(s):  
Zhanpeng Zheng ◽  
Chengjun Wu ◽  
Hengliang Wu ◽  
Jianyong Wang ◽  
Xiaofei Lei
Keyword(s):  
Theoretical Model ◽  
Dynamic Response ◽  
Vibration Isolation ◽  
Passive Control ◽  
Vibration Energy ◽  
Damping Force ◽  
Damping Effect ◽  
Particle Damping ◽  
Vibration Isolation Performance ◽  
Isolation Performance

Nonobstructive particle damping (NOPD) is a novel passive control technology with strong nonlinear-damping. Many scholars put effort into the research on the internal mechanism of NOPD. In contrast, the application of NOPD to engineering has not received much research effort. A theoretical model based on the principle of gas–solid flows, which is employed to evaluate damping effect of NOPD and to predict dynamic response of a machine rack by a co-simulation approach, is established in this paper. In view of the difference between damping effect acting on the lateral and bottom of NOPD holes directly, total damping force is divided into lateral damping force and bottom damping force according to the Janssen theory of stress changed direction. Moreover, NOPD technology is applied to a machine rack for discussing its vibration isolation performance. The results indicate that NOPD technology can suppress the intense vibration, especially between 4000 Hz and 8000 Hz. It is noted that the theoretical model of NOPD can accurately predict the dynamic response of the machine rack with NOPD. The 1/3 Octave vibration energy spectrum indicates that NOPD technics can dissipate the vibration energy of the machine rack at full frequency, especially in 31.5 Hz, and attenuation up to 39.75 dB.

scholarly journals High-Efficiency Vibration Isolation for a Three-Phase Power Transformer by a Quasi-Zero-Stiffness Isolator

2021 ◽  
Vol 2021 ◽  
pp. 1-11
Author(s):  
Hao Cao ◽  
Yaopeng Chang ◽  
Jiaxi Zhou ◽  
Xuhui Zhao ◽  
Ling Lu ◽  
...  
Keyword(s):  
Vibration Isolation ◽  
High Efficiency ◽  
Power Transformer ◽  
Dynamic Stiffness ◽  
Harmonic Balance Method ◽  
Isolation System ◽  
Three Phase ◽  
Engineering Practices ◽  
Vibration Isolation Performance ◽  
Isolation Performance

The vibrations generated by a three-phase power transformer reduce the comfort of residents and the service life of surrounding equipment. To resolve this tough issue, a quasi-zero-stiffness (QZS) isolator for the transformer is proposed. This paper is devoted to developing a QZS isolator in a simple way for engineering practices. The vertical springs are used to support the heavy weight of the transformer, while the oblique springs are employed to fulfill negative stiffness to neutralize the positive stiffness of the vertical spring. Hence, a combination of the vertical and oblique spring can yield high static but low dynamic stiffness, and the vibration isolation efficiency can be improved substantially. The dynamic analysis for the QZS vibration isolation system is conducted by the harmonic balance method, and the vibration isolation performance is estimated. Finally, the prototype of the QZS isolator is manufactured, and then the vibration isolation performance is tested comparing with the linear isolator under real power loading conditions. The experimental results show that the QZS isolator prominently outperforms the existing linear isolator. This is the first time to devise a QZS isolator for three-phase power transformers with heavy payloads in engineering practices.

scholarly journals An Asymmetric Quasi-zero Stiffness Vibration Isolator with Long Stroke and Large Bearing Capacity

2021 ◽  
Author(s):  
Xinghua Zhou ◽  
Dingxuan Zhao ◽  
Xiao Sun ◽  
Xiao Yang ◽  
Jianhai Zhang ◽  
...  
Keyword(s):  
Bearing Capacity ◽  
Vibration Isolation ◽  
Geometrical Nonlinearity ◽  
Harmonic Balance Method ◽  
Nonlinear Damping ◽  
Vibration Isolator ◽  
Plate Spring ◽  
Supporting Force ◽  
Vibration Isolation Performance ◽  
Isolation Performance

Abstract A novel passive asymmetric quasi-zero stiffness vibration isolator (AQZS-VI) comprising two linear springs acting in parallel with one negative stiffness element (NSE) is proposed, of which the NSE is mainly constructed by the combination of cantilever plate spring and L-shaped lever (CPS-LSL). The static model of the isolator is deduced considering the geometrical nonlinearity of the NSE and the bending deformation of plate spring. The nonlinear stiffness properties of the CPS-LSL and the AQZS-VI, as well as the nonlinear damping properties of the AQZS-VI are discussed. The absolute displacement transmissibility of the AQZS-VI under base displacement excitation is obtained using Harmonic Balance Method, and the effects of different excitation amplitudes and damping factors on the vibration isolation performance are analyzed. Better than other quasi-zero stiffness vibration isolators (QZS-VI) whose NSEs do not provide supporting force at zero stiffness point, the NSE of the AQZS-VI provides more supporting force than the parallel connected linear springs, which is very beneficial for improving the bearing capacity of the isolator. Compared with a typical symmetric QZS-VI with same damping property, the AQZS-VI has longer stroke with low stiffness and lower peak value of displacement transmissibility. The prototype experiments indicate that the AQZS-VI outperforms the linear counterpart with much smaller starting frequency of vibration isolation and lower displacement transmissibility. The proposed AQZS-VI has great potential for applying in various engineering practices with superior vibration isolation performance.

Design and Dynamic Characteristics of a Torsion Isolator With Negative Stiffness Structures

2016 ◽  
Author(s):  
Hui Liu ◽  
Xiaojie Wang ◽  
Weida Wang ◽  
Changle Xiang
Keyword(s):  
Harmonic Balance ◽  
Vibration Isolation ◽  
Harmonic Balance Method ◽  
Negative Stiffness ◽  
Frequency Range ◽  
Disk Structure ◽  
Vibration Transmissibility ◽  
Low Stiffness ◽  
Vibration Isolation Performance ◽  
Isolation Performance

This paper proposes a torsion isolator with negative stiffness structures, which has low stiffness. The torsion isolator has been designed into disk structure, which is the installation position of the positive springs and negative stiffness structures. In this paper, the model of the torsion isolator is introduced firstly, and the nonlinear stiffness and torque are studied under different compression deformation of springs in negative stiffness structures. Then a two-degree-freedom equation of the torsional isolator is established and vibration transmissibility is obtained by using Harmonic Balance Method. Theoretical analysis results show that the isolator with negative stiffness structures has larger isolation frequency range than linear isolator. Finally, an initial experiment is completed. The experimental results show that the isolator has a good vibration isolation performance.

On vibration isolation of sandwich plate with periodic hollow tube core

2017 ◽  
Vol 21 (3) ◽  
pp. 1119-1132 ◽  
Author(s):  
Gui-Lan Yu ◽  
Hong-Wei Miao
Keyword(s):  
Vibration Isolation ◽  
Sandwich Plate ◽  
Experimental Studies ◽  
Low Frequency ◽  
Dispersion Relations ◽  
Frequency Responses ◽  
Vibration Attenuation ◽  
Potential Applications ◽  
Vibration Isolation Performance ◽  
Isolation Performance

The vibration isolation performance of a PC sandwich plate with periodic hollow tube core is investigated experimentally and numerically. The experiment results reveal that there exist vibration attenuation zones in acceleration frequency responses which can be improved by increasing the number of periods or tuning some structure parameters. The presence of soft fillers shifts the attenuation zone to lower frequencies and enhances the capability of vibration isolation to some extent. Dispersion relations and acceleration frequency responses are calculated by finite element method using COMSOL MULTIPHYSICS. The attenuation zones obtained by experiments fit well with that by simulations, and both are consistent with the band gap in dispersion relations. The numerical and experimental studies in the present paper show that this PC sandwich plate exhibits a good performance on vibration isolation in low frequency ranges, which will provide some useful references for relevant research and potential applications in vibration propagation manipulations.

scholarly journals Vibration isolation performance of an elevator motor using Nitrile-Butadiene Rubber /Multi-Walled Carbon Nanotube composite machine mounts

2020 ◽  
Vol 318 ◽  
pp. 01050
Author(s):  
Konstantinos Tsongas ◽  
Gabriel Mansour
Keyword(s):  
Vibration Isolation ◽  
Element Model ◽  
Test System ◽  
Damping Capacity ◽  
Butadiene Rubber ◽  
Motor Test ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes ◽  
Vibration Isolation Performance ◽  
Isolation Performance

The objective of this paper is to evaluate the vibration isolation performance of an elevator motor mounted on elastomeric nanocomposite mounts. A series of conventional acrylonitrile-butadiene rubber (NBR) mounts have been reinforced with 20wt% concentration of multi-walled carbon nanotubes (MWCNTs). The vibration isolation capacity of the machine mounts was calculated through the transmissibility of an elevator motor test system. A Finite Element Model (FEM) was introduced and a harmonic analysis based on the ANSYS code has been utilized to investigate the modal behavior of the nanocomposite machine mount/elevator motor system and extract a representative model of the vibrational behavior. The cyclic compression results have revealed that the stiffness and damping capacity of the conventional elastomers can be modified by adjusting the proportion of MWCNTs. Elastomers’ vibration isolation performance of the motor was ameliorated with the inclusion of MWCNTs, signifying that the enhancement of the elastomers with MWCNTs was rather effective. The vibration level of the elevator motor was decreased to 90% by incorporating the optimal concentration of MWCNTs in NBR mounts.

Optimization of Vehicle Powertrain Mounting System and its Performance

2013 ◽  
Vol 441 ◽  
pp. 580-583
Author(s):  
Gong Yu Pan ◽  
Xin Yang ◽  
You Yan
Keyword(s):  
Vibration Isolation ◽  
Dynamics Model ◽  
Acceleration Response ◽  
Idle State ◽  
Decoupling Method ◽  
Before And After ◽  
Vibration Transmissibility ◽  
Six Degree Of Freedom ◽  
Vibration Isolation Performance ◽  
Isolation Performance

In order to solve the vibration problem of diesel engine powertrain assembly at its idle state, a six degree-of-freedom dynamics model of the powertrain mounting system is established and a optimization based on Adams/View is applied to simulation and analysis on the powertrain mounting system with energy decoupling method. The results show that the optimized repositioning mounts installation position can effectively improve decoupling rate in main vibration directions of mounting system. Based on this, the vibration transmissibility and acceleration response before and after optimization are simulated. The results show that the optimized engine mounting system makes a great improvement of vibration isolation performance.

The Experimental Research of Vibration Isolation Performance of MR Isolator at High Temperature

2012 ◽  
Vol 184-185 ◽  
pp. 525-528 ◽  
Author(s):  
Hui Yan ◽  
Liang Chen ◽  
Hong Rui Ao ◽  
Hong Yuan Jiang
Keyword(s):  
Vibration Isolation ◽  
Evaluation Index ◽  
Structural Parameter ◽  
Sweep Frequency ◽  
Frequency Test ◽  
Metal Rubber ◽  
Performance Evaluation Index ◽  
Vibration Isolation Performance ◽  
Isolation Performance ◽  
Sine Sweep

Transmissibility is the main performance evaluation index of Metal Rubber (MR) isolator, which can be got by sine sweep frequency test. At different temperature, the sine sweep frequency test is done with different structural parameter MR isolator. The influence that relative density and pre-deformation have on transmissibility and natural frequency when temperature changed is analyzed. The changing regularity of MR isolator’s transmissibility at different temperature is explored. Research results provide the basis for designing MR isolator.

Vibration and Shock Isolation Performance of a Semi-Active “On-Off” Damper

1985 ◽  
Vol 107 (4) ◽  
pp. 398-403 ◽  
Author(s):  
S. Rakheja ◽  
S. Sankar
Keyword(s):  
Relative Position ◽  
Relative Velocity ◽  
Vibration Isolation ◽  
Performance Characteristics ◽  
Orifice Area ◽  
Hydraulic Damper ◽  
Control Scheme ◽  
Vibration Isolation Performance ◽  
Isolation Performance ◽  
Command Signal

The concept of an “on-off” damper employing the feedback signals from directly measurable variables is proposed. A control scheme utilizing the directly measurable relative position and relative velocity signals to produce the command signal is configured. The on-off damping mechanism can be achieved through the modulation of orifice area in a conventional hydraulic damper, using a two position on-off valve driven by the command signal. The shock and vibration isolation characteristics of the proposed on-off damper are evaluated through computer simulations. The shock and vibration isolation performance characteristics of the proposed damper are compared to the performance characteristics of a passive and an on-off damper utilizing the feedback from absolute and relative velocity signals.

Sign in / Sign up

Export Citation Format

Share Document