scholarly journals Wind Turbines Optimal Operation at Time Variable Wind Speeds

2020 ◽  
Vol 10 (12) ◽  
pp. 4232
Author(s):  
Mihaela-Codruta Ancuti ◽  
Sorin Musuroi ◽  
Ciprian Sorandaru ◽  
Marian Dordescu ◽  
Geza Mihai Erdodi
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Optimal Operation ◽  
Time Variable ◽  
Total Power ◽  
Proportional Integral ◽  
Wind Speeds ◽  
Variable Wind ◽  
Power Curves ◽  
Large Moment

The wind turbine’s operation is affected by the wind speed variations, which cannot be followed by the wind turbine due to the large moment of the power plant’s inertia. The method proposed in this paper belongs to the wind turbine power curves (WTPC) approach, which expresses the power curve of the permanent magnet synchronous generator (PMSG) by a set of mathematical equations. The WTPC research papers published before now have not taken into consideration the total power plant inertia at time-variable wind speeds, when the wind turbine’s optimal operation is very difficult to be reached, and its efficiency is thus threatened. The study is based on a wind turbine having a large moment of total inertia, and demonstrates, through extensive simulation results, that the optimal values of the PMSG’s power can be determined based on the kinetic motion equation. This PMSG’s optimal power represents an ideal time-varying curve, and the wind turbine should be controlled so as to closely follow it. For this purpose, proportional integral (PI) and proportional integral derivative (PID) type-based control methods were implemented and analyzed, so that the PMSG’s power oscillations could be reduced, and the PMSG’s angular speed value made comparable to the optimal one, meaning that the wind turbine operates within the optimal operation area, and is efficient. The simulations are actually the numerical solutions obtained by using the Scientific Workplace simulation environment, and they are based on the wind speed measurements collected from a wind farm located in Dobrogea, Romania.

scholarly journals Analysis of the Wind System Operation in the Optimal Energetic Area at Variable Wind Speed over Time

2019 ◽  
Vol 11 (5) ◽  
pp. 1249 ◽  
Author(s):  
Ciprian Sorandaru ◽  
Sorin Musuroi ◽  
Flaviu Frigura-Iliasa ◽  
Doru Vatau ◽  
Marian Dordescu
Keyword(s):  
Wind Speed ◽  
Angular Velocity ◽  
Optimal Operation ◽  
Wind System ◽  
Optimal Velocity ◽  
Electric Generator ◽  
Wind Speeds ◽  
Power Point ◽  
Variable Wind ◽  
Over Time

Due to high mechanical inertia and rapid variations in wind speed over time, at variable wind speeds, the problem of operation in the optimal energetic area becomes complex and in due time it is not always solvable. No work has been found that analyzes the energy-optimal operation of a wind system operating at variable wind speeds over time and that considers the variation of the wind speed over time. In this paper, we take into account the evolution of wind speed over time and its measurement with a low-power turbine, which operates with no load at the mechanical angular velocity ωMAX. The optimal velocity is calculated. The energy that is captured by the wind turbine significantly depends on the mechanical angular velocity. In order to perform a function in the maximum power point (MPP) power point area, the load on the electric generator is changed, and the optimum mechanical velocity is estimated, ωOPTIM, knowing that the ratio ωOPTIM/ωMAX does not depend on the time variation of the wind speed.

Comparison of Various Blade Profiles in a Two-Blade Conventional Savonius Wind Turbine

2020 ◽  
Vol 143 (2) ◽  
Author(s):  
Rahim Hassanzadeh ◽  
Milad Mohammadnejad ◽  
Sajad Mostafavi
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Power Output ◽  
Urban Areas ◽  
Cost Effective ◽  
Maximum Power ◽  
Power Coefficient ◽  
Total Power ◽  
Wind Speeds ◽  
Savonius Wind Turbine

Abstract Savonius turbines are one of the old and cost-effective turbines which extract the wind energy by the drag force. Nowadays, they use in urban areas to generate electricity due to their simple structure, ease of maintenance, and acceptable power output under a low wind speed. However, their efficiency is low and the improvement of their performance is necessary to increase the total power output. This paper compares four various blade profiles in a two-blade conventional Savonius wind turbine. The ratios of blade diameter to the blade depth of s/d = 0.3, 0.5, 0.7, and 1 are tested under different free-wind speeds of 3, 5, and 7 m/s and tip speed ratios (TSRs) in the range from 0.2 to 1.2. It is found that the profile of blades in a Savonius rotor plays a considerable role in power characteristics. Also, regardless of blades profile and free-wind speed, the maximum power coefficient develops in TSR = 0.8. In addition, increasing the free-wind speed enhances the rotor performance of all cases under consideration. Finally, it is revealed that the rotor with s/d = 0.5 provides maximum power coefficients in all free-wind speeds and TSR values among the rotors under consideration, whereas the rotor with s/d = 1 is the worth cases.

scholarly journals Wind Turbine Power Curves Based on the Weibull Cumulative Distribution Function

2018 ◽  
Vol 8 (10) ◽  
pp. 1757 ◽  
Author(s):  
Neeraj Bokde ◽  
Andrés Feijóo ◽  
Daniel Villanueva
Keyword(s):  
Distribution Function ◽  
Wind Speed ◽  
Wind Turbine ◽  
Software Package ◽  
Cumulative Distribution Function ◽  
Cumulative Distribution ◽  
Weibull Distributions ◽  
Wind Speeds ◽  
Power Curves ◽  
Logistic Functions

The representation of a wind turbine power curve by means of the cumulative distribution function of a Weibull distribution is investigated in this paper, after having observed the similarity between such a function and real WT power curves. The behavior of wind speed is generally accepted to be described by means of Weibull distributions, and this fact allows researchers to know the frequency of the different wind speeds. However, the proposal of this work consists of using these functions in a different way. The goal is to use Weibull functions for representing wind speed against wind power, and due to this, it must be clear that the interpretation is quite different. This way, the resulting functions cannot be considered as Weibull distributions, but only as Weibull functions used for the modeling of WT power curves. A comparison with simulations carried out by assuming logistic functions as power curves is presented. The reason for using logistic functions for this validation is that they are very good approximations, while the reasons for proposing the use of Weibull functions are that they are continuous, simpler than logistic functions and offer similar results. Additionally, an explanation about a software package has been discussed, which makes it easy to obtain Weibull functions for fitting WT power curves.

Statistical calculation of thrust curve of a wind turbine based on available power curve and general specifications data

2021 ◽  
Author(s):  
Evgeny Atlaskin ◽  
Irene Suomi ◽  
Anders Lindfors
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Wind Farm ◽  
Wind Farms ◽  
Power Curve ◽  
Wake Effect ◽  
Thrust Coefficient ◽  
Simple Method ◽  
Wind Speeds ◽  
Power Curves

<p>Power curves for a substantial number of wind turbine generators (WTG) became available in a number of public sources during the recent years. They can be used to estimate the power production of a wind farm fleet with uncertainty determined by the accuracy and consistency of the power curve data. However, in order to estimate power losses inside a wind farm due to wind speed reduction caused by the wake effect, information on the thrust force, or widely used thrust coefficient (Ct), is required. Unlike power curves, Ct curves for the whole range of operating wind speeds of a WTG are still scarcely available in open sources. Typically, power and Ct curves are requested from a WTG manufacturer or wind farm owner under a non-disclosure agreement. However, in a research study or in calculations over a multitude of wind farms with a variety of wind turbine models, collecting this information from owners may be hardly possible. This study represents a simple method to define Ct curve statistically using power curve and general specifications of WTGs available in open sources. Preliminary results demonstrate reasonable correspondence between simulated and given data. The estimations are done in the context of aggregated wind power calculations based on reanalysis or forecast data, so that the uncertainty of wake wind speed caused by the uncertainty of predicted Ct is comparable, or do not exceed, the uncertainty of given wind speed. Although the method may not provide accurate fits at low wind speeds, it represents an essential alternative to using physical Computational Fluid Dynamics (CFD) models that are both more demanding to computer resources and require detailed information on the geometry of the rotor blades and physical properties of the rotor, which are even more unavailable in open sources than power curves.</p>

SHAPING OF AN AUTONOMOUS POWER SYSTEM FOR GUARANTEED POWER SUPPLY WITH THE PREDOMINANCE WIND ENERGY

2018 ◽  
pp. 28-50
Author(s):  
S. G. Ignatiev ◽  
S. V. Kiseleva
Keyword(s):  
Energy Storage ◽  
Wind Speed ◽  
Wind Energy ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Energy Demand ◽  
Diesel Generator ◽  
Average Wind Speed ◽  
Wind Speeds ◽  
Average Wind

Optimization of the autonomous wind-diesel plants composition and of their power for guaranteed energy supply, despite the long history of research, the diversity of approaches and methods, is an urgent problem. In this paper, a detailed analysis of the wind energy characteristics is proposed to shape an autonomous power system for a guaranteed power supply with predominance wind energy. The analysis was carried out on the basis of wind speed measurements in the south of the European part of Russia during 8 months at different heights with a discreteness of 10 minutes. As a result, we have obtained a sequence of average daily wind speeds and the sequences constructed by arbitrary variations in the distribution of average daily wind speeds in this interval. These sequences have been used to calculate energy balances in systems (wind turbines + diesel generator + consumer with constant and limited daily energy demand) and (wind turbines + diesel generator + consumer with constant and limited daily energy demand + energy storage). In order to maximize the use of wind energy, the wind turbine integrally for the period in question is assumed to produce the required amount of energy. For the generality of consideration, we have introduced the relative values of the required energy, relative energy produced by the wind turbine and the diesel generator and relative storage capacity by normalizing them to the swept area of the wind wheel. The paper shows the effect of the average wind speed over the period on the energy characteristics of the system (wind turbine + diesel generator + consumer). It was found that the wind turbine energy produced, wind turbine energy used by the consumer, fuel consumption, and fuel economy depend (close to cubic dependence) upon the specified average wind speed. It was found that, for the same system with a limited amount of required energy and high average wind speed over the period, the wind turbines with lower generator power and smaller wind wheel radius use wind energy more efficiently than the wind turbines with higher generator power and larger wind wheel radius at less average wind speed. For the system (wind turbine + diesel generator + energy storage + consumer) with increasing average speed for a given amount of energy required, which in general is covered by the energy production of wind turbines for the period, the maximum size capacity of the storage device decreases. With decreasing the energy storage capacity, the influence of the random nature of the change in wind speed decreases, and at some values of the relative capacity, it can be neglected.

Stochastic Models of Particle Trajectories in Turbulent Atmosphere Flows by Using the LANGEVIN Equations

Proceedings ◽  
2020 ◽  
Vol 1 (1) ◽  
Author(s):  
Youssra El Qasemy ◽  
Abdelfatah Achahbar ◽  
Abdellatif Khamlichi
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Classical Method ◽  
Degradation Mechanism ◽  
Transformation Process ◽  
Langevin Equations ◽  
Turbulence Data ◽  
Power Curves ◽  
And Diffusion ◽  
Fluctuating Wind

The stochastic behavior of wind speed is a particular characteristic of wind energy production, which affects the degradation mechanism of the turbine, resulting in stochastic charging on the wind turbine. A model stochastic is used in this study to evaluate the efficiency of wind turbine power of whatever degree given fluctuating wind turbulence data. This model is based on the Langevin equations, which characterize, by two coefficients, drift and diffusion functions. These coefficients describe the behavior of the transformation process from the input wind speed to the output data that need to be determined. For this present work, the computation of drift and diffusion functions has been carried out by using the stochastic model to assess the output variables in terms of the torque and power curves as a function of time, and it is compared by the classical method. The results show that the model stochastic can define the efficiency of wind turbine generation more precisely.

scholarly journals Remaining Useful Life Estimation of Wind Turbine Blades under Variable Wind Speed Conditions Using Particle Filters

2018 ◽  
Vol 10 (1) ◽  
Author(s):  
Bhavana Valeti ◽  
Shamim N. Pakzad
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Turbine Blades ◽  
Remaining Useful Life ◽  
Structural Components ◽  
Wind Turbine Blades ◽  
Average Wind Speed ◽  
Average Wind ◽  
Useful Life ◽  
Variable Wind

Rotor blades are the most complex structural components in a wind turbine and are subjected to continuous cyclic loads of wind and self-weight variation. The structural maintenance operations in wind farms are moving towards condition based maintenance (CBM) to avoid premature failures. For this, damage prognosis with remaining useful life (RUL) estimation in wind turbine blades is necessary. Wind speed variation plays an important role influencing the loading and consequently the RUL of the structural components. This study investigates the effect of variable wind speed between the cutin and cut-out speeds of a typical wind farm on the RUL of a damage detected wind turbine blade as opposed to average wind speed assumption. RUL of wind turbine blades are estimated for different initial crack sizes using particle filtering method which forecasts the evolution of fatigue crack addressing the non-linearity and uncertainty in crack propagation. The stresses on a numerically simulated life size onshore wind turbine blade subjected to the above wind speed loading cases are used in computing the crack propagation observation data for particle filters. The effects of variable wind speed on the damage propagation rates and RUL in comparison to those at an average wind speed condition are studied and discussed.

scholarly journals Dynamic response improvement of hybrid system by implementing ANN-GA for fast variation of photovoltaic irradiation and FLC for wind turbine

2015 ◽  
Vol 64 (2) ◽  
pp. 291-314 ◽  
Author(s):  
Maziar Izadbakhsh ◽  
Alireza Rezvani ◽  
Majid Gandomkar
Keyword(s):  
Fuzzy Logic ◽  
Wind Speed ◽  
Dynamic Response ◽  
Wind Turbine ◽  
Hybrid System ◽  
Pitch Angle ◽  
Fuzzy Logic Controller ◽  
Control Method ◽  
Control Technique ◽  
Power Curves

Abstract In this paper, dynamic response improvement of the grid connected hybrid system comprising of the wind power generation system (WPGS) and the photovoltaic (PV) are investigated under some critical circumstances. In order to maximize the output of solar arrays, a maximum power point tracking (MPPT) technique is presented. In this paper, an intelligent control technique using the artificial neural network (ANN) and the genetic algorithm (GA) are proposed to control the MPPT for a PV system under varying irradiation and temperature conditions. The ANN-GA control method is compared with the perturb and observe (P&O), the incremental conductance (IC) and the fuzzy logic methods. In other words, the data is optimized by GA and then, these optimum values are used in ANN. The results are indicated the ANN-GA is better and more reliable method in comparison with the conventional algorithms. The allocation of a pitch angle strategy based on the fuzzy logic controller (FLC) and comparison with conventional PI controller in high rated wind speed areas are carried out. Moreover, the pitch angle based on FLC with the wind speed and active power as the inputs can have faster response that lead to smoother power curves, improving the dynamic performance of the wind turbine and prevent the mechanical fatigues of the generator

scholarly journals Numerical Simulation of the Aeroelastic Response of Wind Turbines in Typhoons Based on the Mesoscale WRF Model

2019 ◽  
Vol 12 (1) ◽  
pp. 34
Author(s):  
Long Wang ◽  
Cheng Chen ◽  
Tongguang Wang ◽  
Weibin Wang
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Wind Direction ◽  
Flow Direction ◽  
Wrf Model ◽  
Normal Operation ◽  
Average Wind Speed ◽  
Aeroelastic Response ◽  
Response Characteristics ◽  
Wind Speeds

A new simulation method for the aeroelastic response of wind turbines under typhoons is proposed. The mesoscale Weather Research and Forecasting (WRF) model was used to simulate a typhoon’s average wind speed field. The measured power spectrum and inverse Fourier transform method were coupled to simulate the pulsating wind speed field. Based on the modal method and beam theory, the wind turbine model was constructed, and the GH-BLADED commercial software package was used to calculate the aerodynamic load and aeroelastic response. The proposed method was applied to assess aeroelastic response characteristics of a commercial 6 MW offshore wind turbine under different wind speeds and direction variation patterns for the case study of typhoon Hagupit (2008), with a maximal wind speed of 230 km/h. The simulation results show that the typhoon’s average wind speed field and turbulence characteristics simulated by the proposed method are in good agreement with the measured values: Their difference in the main flow direction is only 1.7%. The scope of the wind turbine blade in the typhoon is significantly larger than under normal wind, while that under normal operation is higher than that under shutdown, even at low wind speeds. In addition, an abrupt change in wind direction has a significant impact on wind turbine response characteristics. Under normal operation, a sharp variation of the wind direction by 90 degrees in 6 s increases the wind turbine (WT) vibration scope by 27.9% in comparison with the case of permanent wind direction. In particular, the maximum deflection of the wind tower tip in the incoming flow direction reaches 28.4 m, which significantly exceeds the design standard safety threshold.

Sign in / Sign up

Export Citation Format

Share Document