scholarly journals Effects of Ethanol–Diesel on the Combustion and Emissions from a Diesel Engine at a Low Idle Speed

2020 ◽  
Vol 10 (12) ◽  
pp. 4153 ◽  
Author(s):  
Ho Young Kim ◽  
Jun Cong Ge ◽  
Nag Jung Choi
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Direct Injection ◽  
Maximum Heat ◽  
Idle Speed ◽  
Indicated Mean Effective Pressure ◽  
Combustion Duration ◽  
Mean Size ◽  
Maximum Heat Release ◽  
Blended Fuels

In this study, detailed experiments were conducted on the combustion and exhaust characteristics of ethanol–diesel blended fuels. The four-stroke four-cylinder common-rail direct injection diesel engine was used. The experiment was carried out at 750 rpm at a low speed idle, and a 40 Nm engine load was applied to simulate the operation of the accessories during the low idle operation of the actual vehicles. The test fuels were four types of ethanol-blended fuel. The ethanol blending ratios were 0% (DE_0) for pure diesel, and 3% (DE_3), 5% (DE_5) and 10% (DE_10) for 3%, 5% and 10% ethanol mixtures (by vol.%). Blending ethanol with diesel fuel increased the maximum combustion pressure by up to 4.1% compared with that of pure diesel fuel, and the maximum heat release rate increased by 13.5%. The brake specific fuel consumption (BSFC) increased, up to 5.9%, as the ethanol blending ratio increased, while the brake thermal efficiency (BTE) for diesel-ethanol blended fuels remained low, and was maintained at 23.8%. The coefficient of variation (COV) of the indicated mean effective pressure (IMEP) was consistently lower than 1% when ethanol was blended. The blending of ethanol increased the ignition delay from a 12.0 degree crank angle (°CA) at DE_0 to 13.7 °CA at DE_10, and the combustion duration was reduced from 21.5 °CA at DE_0 to 20.8 °CA at DE_10. When ethanol blending was applied, nitrogen oxides (NOx) reduced to 93.5% of the level of pure diesel fuel, the soot opacity decreased from 5.3% to 3% at DE_0, and carbon monoxide increased (CO) by 27.4% at DE_10 compared with DE_0. The presence of hydrocarbon (HC) decreased to 50% of the level of pure diesel fuel, but increased with a further increase in the ethanol blending ratio. The mean size of the soot particulates was reduced by 26.7%, from 33.9 nm for pure diesel fuel, DE_0, to 24.8 nm for DE_10.

The Study about Combustion and Emission Characteristics of n-Butanol/Diesel Fuel Mixture

2014 ◽  
Vol 492 ◽  
pp. 335-340
Author(s):  
Jian Wu ◽  
Li Li Zhu ◽  
Zhan Cheng Wang ◽  
Bin Xu ◽  
Hong Ming Wang
Keyword(s):  
High Pressure ◽  
Diesel Engine ◽  
Diesel Fuel ◽  
Release Rate ◽  
Fuel Mixture ◽  
Emission Characteristics ◽  
Maximum Heat ◽  
Maximum Heat Release ◽  
Hc Emissions ◽  
Increasing Load

Experiment of fuel combustion and emission characteristics was carried on a turbocharged intercooled electronically controlled high pressure common rail diesel engine with n-butanol/diesel blends, then the results of experiment were compared and analyzed. The results show that with the adding of n-butanol, the maximum combustion pressure gradually increases and the maximum heat release rate gradually reduces; compared with diesel, CO emissions of the blends are slightly lower and decrease with the increasing load; HC emissions of the mixture fuel are higher and decrease first then increase with the increasing load; at 2000rpm, NOX emissions of the blends are a little lower than the pure diesel in small loads but higher in other loads, and increase with the adding of the load.

Effect of the altitude on the combustion characteristics of a low-compression-ratio diesel engine during the start-up process

2016 ◽  
Vol 231 (13) ◽  
pp. 1838-1847 ◽  
Author(s):  
Ze-chao Kan ◽  
Zhi-yuan Hu ◽  
Di-ming Lou ◽  
Zhi-yi Cao ◽  
Jie Cao
Keyword(s):  
Diesel Engine ◽  
Compression Ratio ◽  
Peak Pressure ◽  
Direct Injection ◽  
Test System ◽  
Combustion Characteristics ◽  
Indicated Mean Effective Pressure ◽  
Start Up ◽  
Combustion Duration ◽  
Intake Pressure

One of the ways to meet future emission standards for cars and to limit the peak pressure of a heavy-duty, highly supercharged diesel engine is to reduce the compression ratio. Nevertheless, complications appear because stringent limitations to a reduction in the diesel compression ratio are the start-up requirements, in particular at high altitudes. An experimental study was conducted on the effect of the altitude on the combustion characteristics during the start-up process of a direct-injection midspeed intercooled turbocharged diesel engine with a compression ratio of 14.25:1. Specialized testing was conducted on the low-compression-ratio diesel engine, the intake pressure and the exhaust pressure of which were controlled by a plateau simulation test system to simulate the conditions at altitudes of 0 m, 1000 m, 2000 m, 3000 m, 3750 m and 4500 m. The results indicated that the pressure in the cylinder was lower during the cranking period as the altitude increased and that this caused the ignition operation to become difficult at altitudes above 3000 m. The combustion characteristics are significantly impacted by altitudes above 2000 m. At an altitude of 0–1000 m, the curve pattern of the cycle cylinder pressure had mainly a single peak during the start-up period. When the altitude increased to 2000 m, twin peaks and afterburn appeared in the cycles. Misfire appeared during the start-up period when the altitude increased to 3000 m, the combustion instability increased and the average indicated mean effective pressure decreased rapidly. When the altitude increases, the cycle-to-cycle variations in the peak pressure increased during idle, the ignition and the crank angle position at 50% of the cumulative heat release rate were delayed and the combustion duration was extended.

scholarly journals An experimental study of the combusition and emission performances of 2,5-dimethylfuran diesel blends on a diesel engine

2017 ◽  
Vol 21 (1 Part B) ◽  
pp. 543-553 ◽  
Author(s):  
Helin Xiao ◽  
Pengfei Zeng ◽  
Liangrui Zhao ◽  
Zhongzhao Li ◽  
Xiaowei Fu
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Direct Injection ◽  
Operating Conditions ◽  
Effective Pressure ◽  
Compression Ignition Engine ◽  
Brake Mean Effective Pressure ◽  
Combustion Duration ◽  
Significant Difference ◽  
Hc Emissions

Experiments were carried out in a direct injection compression ignition engine fueled with diesel-dimethylfuran blends. The combustion and emission performances of diesel-dimethylfuran blends were investigated under various loads ranging from 0.13 to 1.13 MPa brake mean effective pressure, and a constant speed of 1800 rpm. Results indicate that diesel-dimethylfuran blends have different combustion performance and produce longer ignition delay and shorter combustion duration compared with pure diesel. Moreover, a slight increase of brake specific fuel consumption and brake thermal efficiency occurs when a Diesel engine operates with blended fuels, rather than diesel fuel. Diesel-dimethylfuran blends could lead to higher NOx emissions at medium and high engine loads. However, there is a significant reduction in soot emission when engines are fueled with diesel-dimethylfuran blends. Soot emissions under each operating conditions are similar and close to zero except for D40 at 0.13 MPa brake mean effective pressure. The total number and mean geometric diameter of emitted particles from diesel-dimethylfuran blends are lower than pure diesel. The tested fuels exhibit no significant difference in either CO or HC emissions at medium and high engine loads. Nevertheless, diesel fuel produces the lowest CO emission and higher HC emission at low loads of 0.13 to 0.38 MPa brake mean effective pressure.

EMISSION CHARACTERISTICS AND EGR APPLICATION OF BLENDED FUELS WITH BDF AND OXYGENATE (DMM) IN A DIESEL ENGINE

2010 ◽  
Vol 24 (15n16) ◽  
pp. 2850-2855 ◽  
Author(s):  
SEUNG-HUN CHOI ◽  
YOUNG-TAIG OH
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Direct Injection ◽  
Nox Reduction ◽  
Specific Energy Consumption ◽  
Nox Emission ◽  
Biodiesel Fuel ◽  
Oxygenated Fuel ◽  
Blended Fuel ◽  
Blended Fuels

In this study, the possibility of biodiesel fuel and oxygenated fuel (dimethoxy methane ; DMM) was investigated as an alternative fuel for a naturally aspirated direct injection diesel engine. The smoke emission of blending fuel (biodiesel fuel 90vol-% + DMM 10vol-%) was reduced approximately 70% at 2500rpm, full load in comparison with the diesel fuel. But, engine power and brake specific energy consumption showed no significant differences. But, NOx emission of biodiesel fuel and DMM blended fuel increased compared with commercial diesel fuel due to the oxygen component in the fuel. It was needed a NOx reduction counter plan that EGR method was used as a countermeasure for NOx reduction. It was found that simultaneous reduction of smoke and NOx emission was achieved with BDF (95 vol-%) and DMM (5 vol-%) blended fuel and cooled EGR method (15%).

scholarly journals Experimental Investigation of Diesel Engine Performance, Combustion and Emissions Using a Novel Series of Dioctyl Phthalate (DOP) Biofuels Derived from Microalgae

Energies ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1964 ◽  
Author(s):  
Farhad M. Hossain ◽  
Md. Nurun Nabi ◽  
Md. Mostafizur Rahman ◽  
Saiful Bari ◽  
Thuy Chu Van ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Chemical Properties ◽  
Engine Performance ◽  
Dioctyl Phthalate ◽  
Indicated Mean Effective Pressure ◽  
Test Study ◽  
Physico Chemical ◽  
Peak Cylinder Pressure ◽  
Blended Fuels

Physico-chemical properties of microalgae biodiesel depend on the microalgae species and oil extraction method. Dioctyl phthalate (DOP) is a clear, colourless and viscous liquid as a plasticizer. It is used in the processing of polyvinyl chloride (PVC) resin and polymers. A new potential biofuel, hydrothermally liquefied microalgae bio-oil can contain nearly 11% (by mass) of DOP. This study investigated the feasibility of using up to 20% DOP blended in 80% diesel fuel (v/v) in an existing diesel engine, and assessed the performance and exhaust emissions. Despite reasonable differences in density, viscosity, surface tension, and boiling point, blends of DOP and diesel fuel were found to be entirely miscible and no separation was observed at any stage during prolonged miscibility tests. The engine test study found a slight decrease in peak cylinder pressure, brake, and indicated mean effective pressure, indicated power, brake power, and indicated and brake thermal efficiency with DOP blended fuels, where the specific fuel consumption increased. This is due to the presence of 16.4% oxygen in neat DOP, responsible for the relatively lower heating value, compared to that of diesel. The emission tests revealed a slight increase in nitrogen oxides (NOx) and carbon monoxide (CO) emissions from DOP blended fuels. However, particulate matter (PM) emissions were lower from DOP blended fuels, although some inconsistency in particle number (PN) was present among different engine loads.

Explorative Investigation on Cashew Nut Shell Liquid Biodiesel blended with Ethanol and Hydrogen in Direct Injection (DI) Diesel Engine and prediction through Artificial Neural Network

2021 ◽  
Author(s):  
Thanigaivelan V ◽  
Lavanya R
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Direct Injection ◽  
Cashew Nut Shell Liquid ◽  
Single Cylinder ◽  
Direct Injection Diesel Engine ◽  
Cashew Nut ◽  
Di Diesel Engine ◽  
Artificial Neural ◽  
Cashew Nut Shell

Abstract Emission from the DI diesel engine is series setback for environment viewpoint. Intended for that investigates for alternative biofuel is persuaded. The important hitches with the utilization of biofuels and their blends in DI diesel engines are higher emanations and inferior brake-thermal efficiency as associated to sole diesel fuel. In this effort, Cashew nut shell liquid (CNSL) biodiesel, hydrogen and ethanol (BHE) mixtures remained verified in a direct-injection diesel engine with single cylinder to examine the performance and discharge features of the engine. The ethanol remained supplemented 5%, 10% and 15% correspondingly through enhanced CNSL as well as hydrogen functioned twin fuel engine. The experiments done in a direct injection diesel engine with single-cylinder at steadystate conditions above the persistent RPM (1500RPM). Throughout the experiment, emissions of pollutants such as fuel consumption rate (SFC), hydrocarbons (HC), carbon monoxide (CO), nitrogen oxides (NOx) and pressure of the fuel were also measured. cylinders. The experimental results show that, compared to diesel fuel, the braking heat of the biodiesel mixture is reduced by 26.79-24% and the BSFC diminutions with growing addition of ethanol from the CNSL hydrogen mixture. The BTE upsurges thru a rise in ethanol proportion with CNSL hydrogen mixtures. Finally, the optimum combination of ethanol with CNSL hydrogen blends led to the reduced levels of HC and CO emissions with trivial upsurge in exhaust gas temperature and NOx emissions. This paper reconnoiters the routine of artificial neural networks (ANN) to envisage recital, ignition and discharges effect.

scholarly journals THE EFFECT OF DIESEL-BIODIESEL BLENDS ON THE PERFORMANCE AND EXHAUST EMISSIONS OF A DIRECT INJECTION OFF-ROAD DIESEL ENGINE

Transport ◽  
2014 ◽  
Vol 29 (4) ◽  
pp. 440-448 ◽  
Author(s):  
Tomas Mickevičius ◽  
Stasys Slavinskas ◽  
Slawomir Wierzbicki ◽  
Kamil Duda
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Direct Injection ◽  
Engine Performance ◽  
Exhaust Emissions ◽  
Bench Test ◽  
Maximum Pressure ◽  
Cylinder Pressure ◽  
Biodiesel Blends ◽  
Performance And Emission

This paper presents a comparative analysis of the diesel engine performance and emission characteristics, when operating on diesel fuel and various diesel-biodiesel (B10, B20, B40, B60) blends, at various loads and engine speeds. The experimental tests were performed on a four-stroke, four-cylinder, direct injection, naturally aspirated, 60 kW diesel engine D-243. The in-cylinder pressure data was analysed to determine the ignition delay, the Heat Release Rate (HRR), maximum in-cylinder pressure and maximum pressure gradients. The influence of diesel-biodiesel blends on the Brake Specific Fuel Consumption (bsfc) and exhaust emissions was also investigated. The bench test results showed that when the engine running on blends B60 at full engine load and rated speed, the autoignition delay was 13.5% longer, in comparison with mineral diesel. Maximum cylinder pressure decreased about 1–2% when the amount of Rapeseed Methyl Ester (RME) expanded in the diesel fuel when operating at full load and 1400 min–1 speed. At rated mode, the minimum bsfc increased, when operating on biofuel blends compared to mineral diesel. The maximum brake thermal efficiency sustained at the levels from 0.3% to 6.5% lower in comparison with mineral diesel operating at full (100%) load. When the engine was running at maximum torque mode using diesel – RME fuel blends B10, B20, B40 and B60 the total emissions of nitrogen oxides decreased. At full and moderate load, the emission of carbon monoxide significantly raised as the amount of RME in fuel increased.

scholarly journals Effects of Oxygenated Additives with Diesel on the Performance of D I Diesel Engine

2019 ◽  
pp. 1-9 ◽  
Author(s):  
P. Venkateswara Rao ◽  
S. Ramesh ◽  
S. Anil Kumar
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Direct Injection ◽  
Primary Objective ◽  
Nox Emissions ◽  
Oxides Of Nitrogen ◽  
Smoke Emission ◽  
Oxygenated Additives ◽  
Blend Fuel ◽  
Fuel Formulation

The primary objective of this work is to reduce the particulate matter (PM) or smoke emission and oxides of nitrogen (NOx emissions) the two important harmful emissions and to increase the performance of diesel engine by using oxygenated additives with diesel as blend fuel. Formulation of available diesel fuel with additives is an advantage than considering of engine modification for improvement of higher output. From the available additives, three oxygenates are selected for experimentation by considering many aspects like cost, content of oxygen, flashpoint, solubility, seal etc. The selected oxygenates are Ethyl Aceto Acetate (EAA), Diethyl Carbonate (DEC), Diethylene Glycol (DEG). These oxygenates are blended with diesel fuel in proportions of 2.5%, 5% and 7.5% by volume and experiments were conducted on a single cylinder naturally aspirated direct injection diesel engine. From the results the conclusion are higher brake power and lower BSFC obtained for DEC blends at 7.5% of additive as compared to EAA, DEG and diesel at full load. In case of DEC blends the smoke emission is lower, whereas NOx emissions are very low in case of EAA additive blend fuels. The DEC can be considered is the best oxygenating additive to be blend with diesel in a proportion of 7.5% by volume.

Spray and Combustion Characteristics of Biodiesel∕Diesel Blended Fuel in a Direct Injection Common-Rail Diesel Engine

2008 ◽  
Vol 130 (3) ◽  
Author(s):  
Hyun Kyu Suh ◽  
Hyun Gu Roh ◽  
Chang Sik Lee
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Direct Injection ◽  
Injection Rate ◽  
Combustion Characteristics ◽  
Biodiesel Fuel ◽  
Injection Timing ◽  
Pilot Injection ◽  
Blended Fuel ◽  
Conventional Diesel Fuel

The aim of this work is to investigate the effect of the blending ratio and pilot injection on the spray and combustion characteristics of biodiesel fuel and compare these factors with those of diesel fuel in a direct injection common-rail diesel engine. In order to study the factors influencing the spray and combustion characteristics of biodiesel fuel, experiments involving exhaust emissions and engine performance were conducted at various biodiesel blending ratios and injection conditions for engine operating conditions. The macroscopic and microscopic spray characteristics of biodiesel fuel, such as injection rate, split injection effect, spray tip penetration, droplet diameter, and axial velocity distribution, were compared with the results from conventional diesel fuel. For biodiesel blended fuel, it was revealed that a higher injection pressure is needed to achieve the same injection rate at a higher blending ratio. The spray tip penetration of biodiesel fuel was similar to that of diesel. The atomization characteristics of biodiesel show that it has higher Sauter mean diameter and lower spray velocity than conventional diesel fuel due to high viscosity and surface tension. The peak combustion pressures of diesel and blending fuel increased with advanced injection timing and the combustion pressure of biodiesel fuel is higher than that of diesel fuel. As the pilot injection timing is retarded to 15deg of BTDC that is closed by the top dead center, the dissimilarities of diesel and blending fuels combustion pressure are reduced. It was found that the pilot injection enhanced the deteriorated spray and combustion characteristics of biodiesel fuel caused by different physical properties of the fuel.

Sign in / Sign up

Export Citation Format

Share Document