scholarly journals Empirical Thermal Performance Investigation of a Compact Lithium Ion Battery Module under Forced Convection Cooling

2020 ◽  
Vol 10 (11) ◽  
pp. 3732
Author(s):  
Akinlabi A. A. Hakeem ◽  
Davut Solyali
Keyword(s):  
Flow Rate ◽  
Thermal Performance ◽  
Air Flow ◽  
Lithium Ion ◽  
Operating Conditions ◽  
Battery Pack ◽  
Performance Criteria ◽  
Maximum Temperature ◽  
Air Flow Rate ◽  
Worst Case

Lithium ion batteries (LiBs) are considered one of the most suitable power options for electric vehicle (EV) drivetrains, known for having low self-discharging properties which hence provide a long life-cycle operation. To obtain maximum power output from LiBs, it is necessary to critically monitor operating conditions which affect their performance and life span. This paper investigates the thermal performance of a battery thermal management system (BTMS) for a battery pack housing 100 NCR18650 lithium ion cells. Maximum cell temperature (Tmax) and maximum temperature difference (ΔTmax) between cells were the performance criteria for the battery pack. The battery pack is investigated for three levels of air flow rate combined with two current rate using a full factorial Design of Experiment (DoE) method. A worst case scenario of cell Tmax averaged at 36.1 °C was recorded during a 0.75 C charge experiment and 37.5 °C during a 0.75 C discharge under a 1.4 m/s flow rate. While a 54.28% reduction in ΔTmax between the cells was achieved by increasing the air flow rate in the 0.75 C charge experiment from 1.4 m/s to 3.4 m/s. Conclusively, increasing BTMS performance with increasing air flow rate was a common trend observed in the experimental data after analyzing various experiment results.

scholarly journals The effects of operating conditions on the performance of a direct carbon fuel cell

2013 ◽  
Vol 34 (4) ◽  
pp. 187-197 ◽  
Author(s):  
Andrzej Kacprzak ◽  
Rafał Kobyłecki ◽  
Zbigniew Bis
Keyword(s):  
Fuel Cell ◽  
Flow Rate ◽  
Gas Flow ◽  
Air Flow ◽  
Operating Conditions ◽  
Cell Performance ◽  
Fuel Particle ◽  
Air Flow Rate ◽  
Direct Carbon Fuel Cell ◽  
Fuel Particles

Abstract The influences of various operating conditions including cathode inlet air flow rate, electrolyte temperature and fuel particles size on the performance of the direct carbon fuel cell DCFC were presented and discussed in this paper. The experimental results indicated that the cell performance was enhanced with increases of the cathode inlet gas flow rate and cell temperature. Binary alkali hydroxide mixture (NaOH-LiOH, 90-10 mol%) was used as electrolyte and the biochar of apple tree origin carbonized at 873 K was used as fuel. Low melting temperature of the electrolyte and its good ionic conductivity enabled to operate the DCFC at medium temperatures of 723-773 K. The highest current density (601 A m−2) was obtained for temperature 773 K and air flow rate 8.3×106 m3s−1. Itwas shown that too low or too high air flow rates negatively affect the cell performance. The results also indicated that the operation of the DCFC could be improved by proper selection of the fuel particle size.

Numerical Investigation on the Strategies for Reducing the Cell Temperature Gradient of an Indirect Internal Reforming Tubular SOFC

2004 ◽  
Author(s):  
Takafumi Nishino ◽  
Hiroshi Iwai ◽  
Kenjiro Suzuki
Keyword(s):  
Temperature Gradient ◽  
Distribution Pattern ◽  
Flow Rate ◽  
Air Flow ◽  
Maximum Temperature ◽  
Air Flow Rate ◽  
Internal Reforming ◽  
Average Temperature ◽  
Reforming Catalyst ◽  
Catalyst Distribution

Strategies to reduce the temperature gradient of the cell have been numerically examined by using a comprehensive analytical model of an indirect internal reforming tubular SOFC, the first generation of which was presented at the last conference in 2003 (1st ICFCSET). In particular, how the air flow rate, gas inlet temperature and density distribution of reforming catalyst affect the thermal field in the cell has been examined. Based on the calculated results, it has been confirmed that larger air flow rate reduces the maximum temperature and accordingly the temperature gradient of the cell, while lower inlet temperatures of gases reduce only the average temperature of the cell. For the reforming catalyst distribution, it has been determined that the temperature gradient of the cell can be fairly reduced by adjusting the amount and allocation of the catalyst. In addition, it has been revealed that the distribution pattern of the catalyst has little effect on the average temperature, so that the power generation performance of the cell is not affected by the adjustment of the catalyst distribution pattern substantially.

scholarly journals Experimental Study and Performance Analysis of a Portable Atmospheric Water Generator

Energies ◽  
2019 ◽  
Vol 13 (1) ◽  
pp. 73 ◽  
Author(s):  
Wei He ◽  
Pengkun Yu ◽  
Zhongting Hu ◽  
Song Lv ◽  
Minghui Qin ◽  
...  
Keyword(s):  
Flow Rate ◽  
Reference Model ◽  
Air Flow ◽  
Operating Conditions ◽  
Water Yield ◽  
Air Humidity ◽  
Air Flow Rate ◽  
Thermoelectric Coolers ◽  
And Performance ◽  
The Impact

Found in some specific scenarios, drinking water is hard for people to get, such as during expeditions and scientific investigations. First, a novel water generator with only two thermoelectric coolers (Model A) is designed for extracting water from atmospheric vapor and then experimentally studied under a small inlet air flow rate. The impact of operating conditions on surface temperatures of cold/hot sides and water yield are investigated, including the air flow rate and humidity. Alternately, to determine the super performance of Model A, a comparative experiment between Model A and a reference model (Model B) is carried out. The results suggest that both the cold/hot temperature and water yield in Model A increases with the humidity and air flow rate rising. Seen in comparisons of Model A and Model B, it is found that, at an air humidity of 90% and air flow rate of 30 m3/h, the total water yield was increased by 43.4% and the corresponding value reached the maximum increment of 66.7% at an air humidity of 60% and air flow rate of 30 m3/h. These features demonstrate the advantage of Model A especially in low air humidity compared to Model B.

Thermal Performance Analysis Of Solar Air Heaters

1984 ◽  
pp. 1-15
Author(s):  
Mohamad Jamil ◽  
Prof. Madya Amer Nordin Darus
Keyword(s):  
Performance Analysis ◽  
Low Temperature ◽  
Flat Plate ◽  
Flow Rate ◽  
Thermal Performance ◽  
Air Flow ◽  
Design Parameters ◽  
Air Flow Rate ◽  
Governing Equations ◽  
Radiation Exchange

A computer routine to calculate the thermal performance of several different low temperature types of flat-plate air heaters is to be discussed. Analysis of each type is also described. The programme accepts as input real or simulated flux, collector geometry, air flow rate and enviromental data. It computes temperatures and extracts energy as a function of time of the day. The programme evaluates radiation,convection, conduction and wind losses, and the radiation exchange with the enviromental conditions.The procedure used in the derivation of the governing equations is also described. The prediction of performance provided by this programme is particularly useful in comparing performances of different collectors and for studying a specific collector's performance with changes in enviroment and design parameters which can be controlled to some extent by the designer.

scholarly journals Thermal Analysis and Improvements of the Power Battery Pack with Liquid Cooling for Electric Vehicles

Energies ◽  
2019 ◽  
Vol 12 (16) ◽  
pp. 3045 ◽  
Author(s):  
Xia ◽  
Liu ◽  
Huang ◽  
Yang ◽  
Lai ◽  
...  
Keyword(s):  
Thermal Management ◽  
Electric Vehicles ◽  
Thermal Performance ◽  
Lithium Ion ◽  
Battery Pack ◽  
Maximum Temperature ◽  
Design Solution ◽  
Liquid Cooling ◽  
Power Battery ◽  
Reference Design

In order to ensure thermal safety and extended cycle life of Lithium-ion batteries (LIBs) used in electric vehicles (EVs), a typical thermal management scheme was proposed as a reference design for the power battery pack. Through the development of the model for theoretical analysis and numerical simulation combined with the thermal management test bench, the designed scheme could be evaluated. In particular, the three-dimensional transient thermal model was used as the type of model. The test result verified the accuracy and the rationality of the model, but it also showed that the reference design could not reach the qualified standard of thermal performance of the power battery pack. Based on the heat dissipation strategy of liquid cooling, a novel improved design solution was proposed. The results showed that the maximum temperature of the power battery pack dropped by 1 °C, and the temperature difference was reduced by 2 °C, which improved the thermal performance of the power battery pack and consequently provides guidance for the design of the battery thermal management system (BTMS).

scholarly journals Investigations of hydraulic operating conditions of air lift pump with three types of air-water mixers

2015 ◽  
Vol 47 (1) ◽  
pp. 69-85 ◽  
Author(s):  
Marek Kalenik
Keyword(s):  
Water Flow ◽  
Flow Rate ◽  
Air Flow ◽  
Operating Conditions ◽  
Water Delivery ◽  
Air Flow Rate ◽  
Analysis Of Results ◽  
Delivery Pipe ◽  
Air Lift

Abstract: Investigations of hydraulic operating conditions of air lift pump with three types of air-water mixers. The paper presents the analysis of results of the investigations concerning the influence of various constructive solutions of the air-water mixers on hydraulic operating conditions of the air lift pump. The scope of the investigations encompassed the determination of characteristics of delivery head and delivery rate for three types of air-water mixers applied in the constructed air lift pump. Using the obtained results, the efficiency of the three types of air-water mixers applied in this air lift pump was determined. The analysis was carried out and there was checked whether the improved analytical Stenning-Martin model can be used to design air lift pumps with the air-water mixers of these types. The highest capacity in the water transport was reached by the air lift pump with the 1st type air-water mixer, the lowest one – with the 3rd type air-water mixer. The water flow in the air lift pump increases along with the rise in the air flow. The lower are the hydraulic losses generated during flow of the air flux by the air-water mixer, the higher is the air lift pump capacity. Along with the rise in the water delivery head, the capacity of the air lift pump decreases. The highest efficiency is reached by the air lift pump with the 1st type air-water mixer, the lowest – with the 3st type air-water mixer. The efficiency of the air lift pump for the three investigated types of air-water mixers decreases along with the rise in air flow rate and water delivery head. The values of submergence ratio (h/L) of the delivery pipe, calculated with the use of the improved analytical Stenning-Martin model, coincide quite well with the values of h/L determined from the measurements.

scholarly journals Simulation Study on Liquid Cooling of Lithium-ion Battery Pack with a Novel Pipeline Structure

2021 ◽  
Vol 2125 (1) ◽  
pp. 012062
Author(s):  
Chao Lv ◽  
Tianyuan Xia ◽  
Hongxin Yin ◽  
Minghe Sun
Keyword(s):  
Lithium Ion Battery ◽  
Flow Rate ◽  
Temperature Difference ◽  
Heat Dissipation ◽  
Lithium Ion ◽  
Battery Pack ◽  
Maximum Temperature ◽  
Coolant Temperature ◽  
Temperature Uniformity ◽  
Liquid Cooling

Abstract Lithium-ion battery is widely used as the mainstream power source of electric vehicles owing to its high specific energy and low self-discharge rate. However, the performance of the lithium-ion battery is largely hindered by its heat dissipation issue. In this paper, lithium-ion battery pack with main channel and multi-branch channel based on liquid cooling sys-tem is studied. Further, numerical simulation was used to analyze the effects of coolant temperature and flow rate on cooling performance. Based on the original pipeline structure, a new pipeline structure was proposed in the present work. The results show that increasing the cool-ant flow rate not only reduces the maximum temperature of the battery pack, but also reduces the temperature difference. Lowering the coolant temperature could largely decrease the maximum temperature of the battery pack, but it tends to widen the temperature difference and worsen the temperature uniformity. Up-on comparison, maximum temperature is found to be decreased by 0.44K, whereas, the temperature difference of the battery decreased and the temperature uniformity is improved.

Improving the estimation of methodological errors in reproducing the volumetric air flow rate by reference critical nozzle

Metrologiya ◽  
2021 ◽  
pp. 4-30
Author(s):  
V. I. Chesnokov
Keyword(s):  
Kinetic Energy ◽  
Flow Rate ◽  
Gas Flow ◽  
Flow Model ◽  
Air Flow ◽  
Operating Conditions ◽  
Initial Kinetic Energy ◽  
Methodological Error ◽  
Air Flow Rate ◽  
Critical Nozzle

In the development of the previously obtained results a more accurate estimate of the methodological error in reproducing the volumetric air flow rate by reference critical nozzle is given, associated with the choice of the gas flow model and due to taking into account the initial kinetic energy of the flow at the nozzle inlet. Based on improved flow model an analytical evaluation of the methodological error in reproducing the volumetric air flow rate by reference critical nozzle, which is due to a change in the humidity of the working air, has been carried out. It is shown that the methodological error in reproducing the volumetric air flow rate by reference critical nozzle, associated with a change in the air humidity, as well as the analogies methodical error caused by the existence of the initial kinetic energy of the flow, must be taken part in accuracy characteristics at the real operating conditions of the standard volumetric air flow rate using critical nozzles.

Experimental Study of a Solar Air Heater With a New Arrangement of Transverse Longitudinal Baffles

2017 ◽  
Vol 139 (3) ◽  
Author(s):  
Afaq Jasim Mahmood
Keyword(s):  
Heat Transfer ◽  
Flow Rate ◽  
Thermal Efficiency ◽  
Air Flow ◽  
Maximum Temperature ◽  
Maximum Efficiency ◽  
Solar Air Heater ◽  
Air Flow Rate ◽  
Double Pass ◽  
Air Heater

This study presents a new design for improving the convection heat transfer coefficients of double-pass solar air heater. Three cases were described by using a different number of transverse baffles (three, five, and seven) in the lower channel of the collectors; steel mesh sheets were also used to enlarge the heat transfer area. All collectors have a space of 25 mm between its glass covers and a 50 mm depth of air channel. Furthermore, this work examined the effect of air flow rate and baffles number on device's thermal efficiency and outlet temperature. The experimental results indicate raises in the thermal efficiency as the air flow rate goes from 0.011 kg/s to 0.038 kg/s. A maximum efficiency of 68% was obtained from the case of seven baffles at the air flow rate of 0.038 kg/s. Moreover, the difference between collector's inlet and outlet temperatures, ΔT, indicated an inverse relationship with air flow rate. Thus, the results show ΔT increases as the air flow rate reduced. The maximum temperature difference recorded was 54 °C, which achieved using seven baffled solar air heater at 0.011 kg/s air flow rate in the middle of the day. It has also been found that thermal efficiency of double-pass solar air heater is greater than single-pass solar air heater, using same air flow rate and number of baffles. Finally, the pressure drop associated with increasing the number of baffles and air flow rate was deliberated.

Sign in / Sign up

Export Citation Format

Share Document