scholarly journals Design and Application of Daylight-Based Lighting Controller on LED Luminaire

2020 ◽  
Vol 10 (10) ◽  
pp. 3415 ◽  
Author(s):  
Sulee Bunjongjit ◽  
Santipont Ananwattanaporn ◽  
Atthapol Ngaopitakkul ◽  
Chaiyan Jettanasen ◽  
Theerasak Patcharoen
Keyword(s):  
Pulse Width Modulation ◽  
Light Emitting Diode ◽  
Field Tests ◽  
Control Circuit ◽  
Led Driver ◽  
Light Emitting ◽  
Working Space ◽  
Actual Field ◽  
Lighting Systems ◽  
Led Luminaire

This paper proposes a control circuit for Light Emitting Diode (LED) luminaire based on the amount of daylight. This system uses both natural daylight and artificial light from a luminaire to reach the desired illuminance on a working plane. The control circuit operates by receiving an illuminance value from a light sensor and comparing it with a set value in the microcontroller before limiting the light intensity of LED by sending a control Pulse Width Modulation (PWM) signal to the LED driver. In the experimental setup, the controller and a physical model of a working space were built in order to field test the LED daylight control circuit. Electrical characteristics such as voltage, current, and power were measured with a power meter. Illumination characteristics in terms of illuminance on a working plane were determined using a lux meter. The results from actual field tests revealed that this LED control circuit was able to reduce the power consumption of the lighting system while keeping the illuminance on the working plane at the standard value. Both simulation results and the actual experiment of the control circuit proved that it could be used to improve the energy efficiency of both newly installed and retrofitted lighting systems.

scholarly journals A Bidirectional Buck-Boost Converter-Based Switching Ripple Communication Strategy for Intelligent Street Lighting Systems

2021 ◽  
Vol 6 (1) ◽  
pp. 260-275
Author(s):  
Yixuan Zhang ◽  
Yihua Hu ◽  
Zion Tse ◽  
Yuwei Liu ◽  
Jiamei Deng ◽  
...  
Keyword(s):  
Pulse Width Modulation ◽  
Light Emitting Diode ◽  
Boost Converter ◽  
Communication Strategy ◽  
Transmission Scheme ◽  
Transmission Method ◽  
Street Lighting ◽  
Light Emitting ◽  
Control Centre ◽  
Lighting Systems

Abstract The light-emitting diode (LED) is an essential component of intelligent street lighting (ISL) systems. An efficient ISL system can not only reduce power consumption by planning LED illuminating time but also reduce maintenance costs through a high degree of automation. In this paper, a buck-boost converter is used to realise composite transmission of power and signals for an ISL system. The power is modulated by the pulse width modulation (PWM) approach, and the switching ripple generated in the PWM process is utilised as the carrier of the signals transmitted between the remote-control centre and the slave nodes. Moreover, the proposed model involves a ‘request to send (RTS)/confirm to send (CTS)’ mechanism to avoid signal conflicts. Compared with the conventional power line communication (PLC) approach, the proposed transmission scheme has the advantages of simple circuit structure and simple system wiring. Additionally, a simulation model built in MATLAB/Simulink proves the designed transmission method has strong anti-noise ability.

scholarly journals A New Capacitor-Less Buck DC-DC Converter for LED Applications

2017 ◽  
Vol 2017 ◽  
pp. 1-5 ◽  
Author(s):  
Munir Al-Absi ◽  
Zainulabideen Khalifa ◽  
Alaa Hussein
Keyword(s):  
Light Emitting Diode ◽  
Switching Frequency ◽  
Led Driver ◽  
Light Emitting ◽  
Led Lighting ◽  
Full Load ◽  
Lighting Systems

In this paper, a new capacitor-less DC-DC converter is proposed to be used as a light emitting diode (LED) driver. The design is based on the utilization of the internal capacitance of the LED to replace the smoothing capacitor. LED lighting systems usually have many LEDs for better illumination that can reach multiple tens of LEDs. Such configuration can be utilized to enlarge the total internal capacitance and hence minimize the output ripple. Also, the switching frequency is selected such that a minimum ripple appears at the output. The functionality of the proposed design is confirmed experimentally and the efficiency of the driver is 85% at full load.

scholarly journals A Supervisory Control Strategy for Improving Energy Efficiency of Artificial Lighting Systems in Greenhouses

Energies ◽  
2021 ◽  
Vol 14 (1) ◽  
pp. 202
Author(s):  
Gianluca Serale ◽  
Luca Gnoli ◽  
Emanuele Giraudo ◽  
Enrico Fabrizio
Keyword(s):  
Control Strategy ◽  
Light Emitting Diode ◽  
Cost Savings ◽  
Energy Performance ◽  
Lighting System ◽  
Light Emitting ◽  
Artificial Lighting ◽  
Lighting Control ◽  
Lighting Systems ◽  
Power Densities

Artificial lighting systems are used in commercial greenhouses to ensure year-round yields. Current Light Emitting Diode (LED) technologies improved the system efficiency. Nevertheless, having artificial lighting systems extended for hectares with power densities over 50W/m2 causes energy and power demand of greenhouses to be really significant. The present paper introduces an innovative supervisory and predictive control strategy to optimize the energy performance of the artificial lights of greenhouses. The controller has been implemented in a multi-span plastic greenhouse located in North Italy. The proposed control strategy has been tested on a greenhouse of 1 hectare with a lighting system with a nominal power density of 50 Wm−2 requiring an overall power supply of 1 MW for a period of 80 days. The results have been compared with the data coming from another greenhouse of 1 hectare in the same conditions implementing a state-of-the-art strategy for artificial lighting control. Results outlines that potential 19.4% cost savings are achievable. Moreover, the algorithm can be used to transform the greenhouse in a viable source of energy flexibility for grid reliability.

scholarly journals Light Emitting Diodes (LEDs) as Agricultural Lighting: Impact and Its Potential on Improving Physiology, Flowering, and Secondary Metabolites of Crops

2021 ◽  
Vol 13 (4) ◽  
pp. 1985
Author(s):  
Musa Al Murad ◽  
Kaukab Razi ◽  
Byoung Ryong Jeong ◽  
Prakash Muthu Arjuna Samy ◽  
Sowbiya Muneer
Keyword(s):  
Crop Production ◽  
Morphological Changes ◽  
Light Emitting Diode ◽  
Crop Productivity ◽  
Photon Flux ◽  
Flower Initiation ◽  
Nutrient Metabolism ◽  
Light Emitting ◽  
Cultivation Systems ◽  
Lighting Systems

A reduction in crop productivity in cultivable land and challenging environmental factors have directed advancement in indoor cultivation systems, such that the yield parameters are higher in outdoor cultivation systems. In wake of this situation, light emitting diode (LED) lighting has proved to be promising in the field of agricultural lighting. Properties such as energy efficiency, long lifetime, photon flux efficacy and flexibility in application make LEDs better suited for future agricultural lighting systems over traditional lighting systems. Different LED spectrums have varied effects on the morphogenesis and photosynthetic responses in plants. LEDs have a profound effect on plant growth and development and also control key physiological processes such as phototropism, the immigration of chloroplasts, day/night period control and the opening/closing of stomata. Moreover, the synthesis of bioactive compounds and antioxidants on exposure to LED spectrum also provides information on the possible regulation of antioxidative defense genes to protect the cells from oxidative damage. Similarly, LEDs are also seen to escalate the nutrient metabolism in plants and flower initiation, thus improving the quality of the crops as well. However, the complete management of the irradiance and wavelength is the key to maximize the economic efficacy of crop production, quality, and the nutrition potential of plants grown in controlled environments. This review aims to summarize the various advancements made in the area of LED technology in agriculture, focusing on key processes such as morphological changes, photosynthetic activity, nutrient metabolism, antioxidant capacity and flowering in plants. Emphasis is also made on the variation in activities of different LED spectra between different plant species. In addition, research gaps and future perspectives are also discussed of this emerging multidisciplinary field of research and its development.

scholarly journals Increased Plant Quality, Greenhouse Productivity and Energy Efficiency with Broad-Spectrum LED Systems: A Case Study for Thyme (Thymus vulgaris L.)

Plants ◽  
2021 ◽  
Vol 10 (5) ◽  
pp. 960
Author(s):  
Jenny Manuela Tabbert ◽  
Hartwig Schulz ◽  
Andrea Krähmer
Keyword(s):  
Broad Spectrum ◽  
Energy Savings ◽  
Light Emitting Diode ◽  
Thymus Vulgaris ◽  
Light Spectrum ◽  
Light Emitting ◽  
Biomass Yields ◽  
Lighting Systems

A light-emitting diode (LED) system covering plant-receptive wavebands from ultraviolet to far-red radiation (360 to 760 nm, “white” light spectrum) was investigated for greenhouse productions of Thymus vulgaris L. Biomass yields and amounts of terpenoids were examined, and the lights’ productivity and electrical efficiency were determined. All results were compared to two conventionally used light fixture types (high-pressure sodium lamps (HPS) and fluorescent lights (FL)) under naturally low irradiation conditions during fall and winter in Berlin, Germany. Under LED, development of Thymus vulgaris L. was highly accelerated resulting in distinct fresh yield increases per square meter by 43% and 82.4% compared to HPS and FL, respectively. Dry yields per square meter also increased by 43.1% and 88.6% under LED compared to the HPS and FL lighting systems. While composition of terpenoids remained unaffected, their quantity per gram of leaf dry matter significantly increased under LED and HPS as compared to FL. Further, the power consumption calculations revealed energy savings of 31.3% and 20.1% for LED and FL, respectively, compared to HPS. In conclusion, the implementation of a broad-spectrum LED system has tremendous potential for increasing quantity and quality of Thymus vulgaris L. during naturally insufficient light conditions while significantly reducing energy consumption.

Energy Saving Potential of Dynamic Lighting Control in Street Lighting Systems in Libya

2021 ◽  
Vol 7 (1) ◽  
Author(s):  
Salah M Alabani
Keyword(s):  
Total Energy ◽  
Energy Saving ◽  
Light Emitting Diode ◽  
Street Lighting ◽  
Light Emitting ◽  
Energy Saving Potential ◽  
Road Section ◽  
First Case ◽  
Lighting Systems ◽  
Dynamic Lighting

This paper studies the manner of energy consumption in Libyan street lighting systems and general road section. It also suggests proposal system with two cases of operation for an attempt to apply the energy saving program by adopting an optimum method in order to decrease the demand of energy in this section and to reduce the use of uneconomic equipment.The proposal system in this paper introduces the Light Emitting Diode (LED) street lighting technology to be used instead of traditional luminaries High Pressure Sodium (HPS). The proposed system is divided into two cases. The first case discusses the replacement of traditional luminaries (HPS) with energy saving luminaries (LED), while second case explains how integrating control node (dynamic dimmer) into LED in order to dim output lighting in streets will save more energy.This study reaches a result that a significant amount of energy of %47 (about 1092.23 GWh/year) of total energy consumed in street lighting sector could be saved if first case is applied. Moreover, it suggests that more energy of %58 (about 1380.02 GWh/year) of total energy consumed in the same sector cloud be saved if the second case is adopted.

Design, Measurements and Characterization of Smart Electronic Board for PV Streetlight based on LED and High Intensity Discharge Lamps

2013 ◽  
pp. 153-165
Author(s):  
Paolo Visconti ◽  
Daniele Romanello ◽  
Giovanni Zizzari ◽  
Vito Ventura ◽  
Giorgio Cavalera
Keyword(s):  
Rural Areas ◽  
High Intensity ◽  
Light Emitting Diode ◽  
Light Emitting ◽  
Electronic Board ◽  
Lighting Systems ◽  
And Control ◽  
Near Future ◽  
Hid Lamps

This work presents an electronic board for driving and control of High Intensity Discharge (HID) lamps and Light Emitting Diode (LED) lamps. The proposed electronic board is able to drive HID or LED lamps by means of a reconfigurable output. This feature allows using the ballast in lighting systems that currently use traditional discharge lamps, as well as keeping the same ballast when discharge lamps are replaced by LED modules in the near future, when LED street lighting systems will be more affordable. Additionally, since the lighting system is designed to be used in rural areas where there is no public electricity, each lighting point incorporates a system to convert solar energy into continuous voltage by means of photovoltaic panels. In this work, energy saving issues are taken into account.

Thermal Performance of a Light Emitting Diode Light Engine for a Multipurpose Automotive Exterior Lighting System With Competing Board Technologies

2017 ◽  
Vol 139 (2) ◽  
Author(s):  
Umut Zeynep Uras ◽  
Mehmet Arık ◽  
Enes Tamdoğan
Keyword(s):  
Thermal Performance ◽  
Computational Models ◽  
Printed Circuit Boards ◽  
Light Emitting Diode ◽  
Ambient Conditions ◽  
Vapor Chamber ◽  
Metal Core ◽  
Light Emitting ◽  
Lighting Systems ◽  
Light Engine

In recent years, light emitting diodes (LEDs) have become an attractive technology for general and automotive illumination systems replacing old-fashioned incandescent and halogen systems. LEDs are preferable for automobile lighting applications due to its numerous advantages such as low power consumption and precise optical control. Although these solid state lighting (SSL) products offer unique advantages, thermal management is one of the main issues due to severe ambient conditions and compact volume. Conventionally, tightly packaged double-sided FR4-based printed circuit boards (PCBs) are utilized for both driver electronic components and LEDs. In fact, this approach will be a leading trend for advanced internet of things applications embedded LED systems in the near future. Therefore, automotive lighting systems are already facing with tight-packaging issues. To evaluate thermal issues, a hybrid study of experimental and computational models is developed to determine the local temperature distribution on both sides of a three-purpose automotive light engine for three different PCB approaches having different materials but the same geometry. Both results showed that FR4 PCB has a temperature gradient (TMaxBoard to TAmbient) of over 63 °C. Moreover, a number of local hotspots occurred over FR4 PCB due to low thermal conductivity. Later, a metal core PCB is investigated to abate local hot spots. A further study has been performed with an advanced heat spreader board based on vapor chamber technology. Results showed that a thermal enhancement of 7.4% and 25.8% over Al metal core and FR4-based boards with the advanced vapor chamber substrate is observed. In addition to superior thermal performance, a significant amount of lumen extraction in excess of 15% is measured, and a higher reliability rate is expected.

scholarly journals The Influence of Artificial Lighting Systems on the Cultivation of Algae: The Example of Chlorella vulgaris

Energies ◽  
2020 ◽  
Vol 13 (22) ◽  
pp. 5994
Author(s):  
Beata Brzychczyk ◽  
Tomasz Hebda ◽  
Norbert Pedryc
Keyword(s):  
Chlorella Vulgaris ◽  
Light Emitting Diode ◽  
Radiant Energy ◽  
Biodiesel Production ◽  
Light Emitting ◽  
Artificial Lighting ◽  
Single Side ◽  
Biological Compounds ◽  
Lower Light ◽  
Lighting Systems

Microalgae are a practical source of biological compounds for biodiesel production. This study examined the influence of three different light-emitting diode (LED) systems on the biomass production of green algae Chlorella vulgaris BA0002a. The cultivation was carried out in a photobioreactor illuminated from the bottom with a single side light jacket (PBR I), in a photobioreactor illuminated from the bottom with a double side light jacket (PBR II) and in a photobioreactor illuminated only from the top (PBR III). Research has shown that the intensification of algae cell production and growth depends on the light distribution and exposure time of a single cell to radiation. In the experiment, the highest growth of algae cells was obtained in the photobioreactor with double jacket and lower light panel. The lowest cell growth was observed in the photobioreactor illuminated only from above. For cultures raised in the PBR I and PBR II photobioreactors, increased oxygen production was observed, which was directly related to the increased production of biomass, which in turn was dependent on the increased amount of radiant energy.

Sign in / Sign up

Export Citation Format

Share Document