scholarly journals Biostimulation in Desert Soils for Microbial-Induced Calcite Precipitation

2020 ◽  
Vol 10 (8) ◽  
pp. 2905 ◽  
Author(s):  
Hadas Raveh-Amit ◽  
Michael Tsesarsky
Keyword(s):  
Soil Liquefaction ◽  
Negev Desert ◽  
Total Carbon ◽  
Arid Environments ◽  
Low Carbon ◽  
Calcium Carbonate Precipitation ◽  
Calcite Precipitation ◽  
Total Carbon Content ◽  
Desert Soils ◽  
Precipitation Medium

Microbial-induced calcite precipitation (MICP) is a soil amelioration technique aiming to mitigate different environmental and engineering concerns, including desertification, soil erosion, and soil liquefaction, among others. The hydrolysis of urea, catalyzed by the microbial enzyme urease, is considered the most efficient microbial pathway for MICP. Biostimulated MICP relies on the enhancement of indigenous urea-hydrolyzing bacteria by providing an appropriate enrichment and precipitation medium, as opposed to bioaugmentation, which requires introducing large volumes of exogenous bacterial cultures into the treated soil along with a growth and precipitation medium. Biostimulated MICP in desert soils is challenging as the total carbon content and the bacterial abundance are considerably low. In this study, we examined the biostimulation potential in soils from the Negev Desert, Israel, for the purpose of mitigation of topsoil erosion in arid environments. Incubating soil samples in urea and enrichment media demonstrated effective urea hydrolysis leading to pH increase, which is necessary for calcite precipitation. Biostimulation rates were found to increase with concentrations of energy (carbon) source in the stimulation media, reaching its maximal levels within 3 to 6 days. Following stimulation, calcium carbonate precipitation was induced by spiking stimulated bacteria in precipitation (CaCl2 enriched) media. The results of our research demonstrate that biostimulated MICP is feasible in the low-carbon, mineral soils of the northern Negev Desert in Israel.

scholarly journals Curtailing Carbon Usage with Addition of Functionalized NiFe2O4 Quantum Dots: Toward More Practical S Cathodes for Li–S Cells

2020 ◽  
Vol 12 (1) ◽  
Author(s):  
Ning Li ◽  
Ting Meng ◽  
Lai Ma ◽  
Han Zhang ◽  
JiaJia Yao ◽  
...  
Keyword(s):  
Quantum Dots ◽  
Carbon Content ◽  
High Energy ◽  
High Specific Surface Area ◽  
Total Carbon ◽  
High Energy Density ◽  
Low Carbon ◽  
Total Carbon Content ◽  
Redox Kinetics ◽  
Carbon Fillers

AbstractSmart combination of manifold carbonaceous materials with admirable functionalities (like full of pores/functional groups, high specific surface area) is still a mainstream/preferential way to address knotty issues of polysulfides dissolution/shuttling and poor electrical conductivity for S-based cathodes. However, extensive use of conductive carbon fillers in cell designs/technology would induce electrolytic overconsumption and thereby shelve high-energy-density promise of Li–S cells. To cut down carbon usage, we propose the incorporation of multi-functionalized NiFe2O4 quantum dots (QDs) as affordable additive substitutes. The total carbon content can be greatly curtailed from 26% (in traditional S/C cathodes) to a low/commercial mass ratio (~ 5%). Particularly, note that NiFe2O4 QDs additives own superb chemisorption interactions with soluble Li2Sn molecules and proper catalytic features facilitating polysulfide phase conversions and can also strengthen charge-transfer capability/redox kinetics of overall cathode systems. Benefiting from these intrinsic properties, such hybrid cathodes demonstrate prominent rate behaviors (decent capacity retention with ~ 526 mAh g−1 even at 5 A g−1) and stable cyclic performance in LiNO3-free electrolytes (only ~ 0.08% capacity decay per cycle in 500 cycles at 0.2 A g−1). This work may arouse tremendous research interest in seeking other alternative QDs and offer an economical/more applicable methodology to construct low-carbon-content electrodes for practical usage.

Action of Carbon in Stress Corrosion Cracking of Mild Steel in Nitrate Solutions

CORROSION ◽  
1973 ◽  
Vol 29 (1) ◽  
pp. 37-46 ◽  
Author(s):  
J. FLIS
Keyword(s):  
Carbon Content ◽  
Stress Corrosion ◽  
Stress Corrosion Cracking ◽  
Intergranular Corrosion ◽  
Corrosion Cracking ◽  
Total Carbon ◽  
General Corrosion ◽  
Low Carbon ◽  
Total Carbon Content ◽  
Protective Properties

Abstract The effect of total carbon content on susceptibility of iron to stress corrosion cracking (SCC), on the depth of intergranular corrosion without stresses, anodic polarization curves, and the general corrosion rate was examined on decarburized Armco iron and its ferritic or martensitic alloys with carbon up to 1.4% in 5N NH4NO3 and 5N Ca(NO3)2, pH 5.0, at 75 and 100 C (167 and 212 F). The susceptibility to SCC and intergranular corrosion increased with the carbon content increasing up to about 0.009% or above, and it diminished with further increase in the carbon content. Carbon decreased the ability of iron to passivate (depassivating action), but it also promoted deposition of magnetite and enhanced its protective properties (impeding action). It is suggested that the observed effect of carbon on SCC and intergranular corrosion results from the predominance of the depassivating action at low carbon contents, and the predominance of the impeding action at higher carbon contents.

STRUCTURE AND MAGNETIC PROPERTIES OF WC–50%Cо MODEL ALLOYS CONTAINING TaC ADDITIVES

2018 ◽  
pp. 49-58
Author(s):  
A. A. Zaitsev ◽  
I. Yu. Konyashin ◽  
E. N. Avdeenko ◽  
N. V. Shvyndina ◽  
E. A. Levashov
Keyword(s):  
Magnetic Properties ◽  
Carbon Content ◽  
Lattice Parameter ◽  
Liquid Phase Sintering ◽  
Total Carbon ◽  
Binder Phase ◽  
Low Carbon ◽  
Powder Mixtures ◽  
Total Carbon Content ◽  
Co Alloys

The structure and magnetic properties of model high-cobalt WC–50%Co alloys with different carbon content and 1,6–5,6 wt.% TaC additives are studied. Model alloys are obtained by liquid-phase sintering of powder mixtures at 1420 °C, and their composition is described by the formula: 50%Co + 50%WC + xTaC + yC, where x = 0; 1,6; 2,6; 3,6; 4,6; 5,6 wt.%, y = 0; 0,2; 0,5 wt.%. It is shown that (Ta,W)C phase precipitates are present in all the investigated alloys, whereby at up to 3,6 wt.% TaC concentration the (Ta,W)C grains have a needle shape, and at ³3,6 wt.% TaC concentration the shape of the (Ta,W)C grains becomes spherical. (Ta,W)C phase precipitates are located both in the Co-binder and along the WC grain boundaries. The (Ta,W)C phase lattice parameter in low-carbon alloys lies in the range from 0,4438 nm for the 1,6 % TaC alloy up to 0,4451 nm for the 4,6 % TaC alloy. According to EDX analysis, the concentration of dissolved tungsten in the cobalt phase is independent of the TaC content and strongly depends on the total carbon content, and for alloys with high, elevated and low carbon content it is 7, 12 and 17 wt.%, respectively. TaC addition in alloys with a low and elevated carbon content leads to an increase in coercive force by 875 A/m and a decrease in magnetic saturation by 5–10 Gs·m3/g. The experimental results allowed putting forward a hypothesis about the possibility of forming dispersed tantalumcontaining precipitates in the binder phase.

scholarly journals Carbon Emission Estimation of Assembled Composite Concrete Beams during Construction

Energies ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1810
Author(s):  
Kaitong Xu ◽  
Haibo Kang ◽  
Wei Wang ◽  
Ping Jiang ◽  
Na Li
Keyword(s):  
Life Cycle ◽  
Carbon Emissions ◽  
Emission Reduction ◽  
Carbon Emission ◽  
Composite Beams ◽  
Total Carbon ◽  
Construction Process ◽  
Low Carbon ◽  
Carbon Emission Reduction ◽  
The Government

At present, the issue of carbon emissions from buildings has become a hot topic, and carbon emission reduction is also becoming a political and economic contest for countries. As a result, the government and researchers have gradually begun to attach great importance to the industrialization of low-carbon and energy-saving buildings. The rise of prefabricated buildings has promoted a major transformation of the construction methods in the construction industry, which is conducive to reducing the consumption of resources and energy, and of great significance in promoting the low-carbon emission reduction of industrial buildings. This article mainly studies the calculation model for carbon emissions of the three-stage life cycle of component production, logistics transportation, and on-site installation in the whole construction process of composite beams for prefabricated buildings. The construction of CG-2 composite beams in Fujian province, China, was taken as the example. Based on the life cycle assessment method, carbon emissions from the actual construction process of composite beams were evaluated, and that generated by the composite beam components during the transportation stage by using diesel, gasoline, and electric energy consumption methods were compared in detail. The results show that (1) the carbon emissions generated by composite beams during the production stage were relatively high, accounting for 80.8% of the total carbon emissions, while during the transport stage and installation stage, they only accounted for 7.6% and 11.6%, respectively; and (2) during the transportation stage with three different energy-consuming trucks, the carbon emissions from diesel fuel trucks were higher, reaching 186.05 kg, followed by gasoline trucks, which generated about 115.68 kg; electric trucks produced the lowest, only 12.24 kg.

Transport of soluble organic and inorganic carbon in sandy soils under nitrogen fertilization

1999 ◽  
Vol 79 (2) ◽  
pp. 303-310 ◽  
Author(s):  
F. L. Wang ◽  
A. K. Alva
Keyword(s):  
Nitrogen Fertilization ◽  
Inorganic Carbon ◽  
Average Rate ◽  
Sandy Soils ◽  
Water Soluble ◽  
Total Carbon ◽  
Total Carbon Content ◽  
Water Soluble Organic Carbon ◽  
Isobutylidene Diurea ◽  
Leaching Condition

Leaching of water soluble soil carbon plays an important role in downward transport of soil nutrients and pollutants and may be influenced by soil and management factors. We examined the leaching of water soluble carbon from two sandy soils under nitrogen fertilization by adapting an intermittent leaching-incubation technique using packed soil columns (94 × 10 cm). After 30 d, cumulative amounts of water-soluble organic carbon (SOC) leached from the Candler and Wabasso sand for various treatments in mg C column−1 were: 77 and 302 (NH4NO3), 64 and 265 (control), and 45 and 239 (isobutylidene diurea, IBDU), respectively. The IBDU and NH4NO3 treatments increased the leaching of water-soluble inorganic carbon (SIC), which ranged from 2 to 38 mg C column−1 over 30 d. At the end of eight cycles of leaching/incubation, the total carbon content increased at depth (control and NH4NO3 treatment) in the Candler sand, but decreased in the Wabasso sand. In the first leaching event, the average rate of SOC leaching from the Wabasso sand was 26 mg C column−1 d−1 which dropped rapidly to about 5 mg C column−1 d−1 towards the end of the experiment. The rate of SOC leaching from the Candler sand was much lower (<8 mg C column−1 d−1) than the rate of SOC leaching from the Wabasso sand. Compared with the unamended treatments, application of NH4NO3 increased and IBDU decreased the leaching of SOC in both soils. These effects of N application were considerable during the initial two to three leaching events only. Our results suggest that the initial rainfalls that follow a dry period may be critical for transporting SOC from the upper layer of these sandy soils. Key words: C leaching, sandy soil, intermittent leaching condition, isobutylidene

scholarly journals Carbon Emission Governance Zones at the County Level to Promote Sustainable Development

Land ◽  
2021 ◽  
Vol 10 (2) ◽  
pp. 197
Author(s):  
He Zhang ◽  
Jingyi Peng ◽  
Dahlia Yu ◽  
Lie You ◽  
Rui Wang
Keyword(s):  
Sustainable Development ◽  
Carbon Emission ◽  
Total Carbon ◽  
Small Scale ◽  
County Level ◽  
Low Carbon ◽  
High Carbon ◽  
Governance System ◽  
Medium Carbon ◽  
Indicator Evaluation

Low-carbon governance at the county level has been an important issue for sustainable development due to the large contributions to carbon emission. However, the experiences of carbon emission governance at the county level are lacking. This paper discusses 5 carbon emission governance zones for 1753 counties. The zoning is formed according to a differentiated zoning method based on a multi-indicator evaluation to judge if the governance had better focus and had formulated a differentiated carbon emission governance system. According to zoning results, there is 1 high-carbon governance zone, 2 medium-carbon governance zones, and 2 low-carbon zones. The extensive high-carbon governance zone and medium-carbon zones are key governance areas, in which the counties are mainly located in the northern plain areas and southeast coastal areas and have contributed 51.88% of total carbon emissions. This paper proposes differentiated governance standards for each indicator of the 5 zones. The differentiated zoning method mentioned in this paper can be applied to other governance issues of small-scale regions.

scholarly journals Characteristics of Liparis loeselii (L.) Rich. populations in selected Natura 2000 areas in eastern Poland

2020 ◽  
Vol 55 (3) ◽  
pp. 151-162
Author(s):  
Danuta Urban ◽  
Joanna Sender ◽  
Ewelina Tokarz ◽  
Andrzej Różycki
Keyword(s):  
Natura 2000 ◽  
Total Carbon ◽  
Habitat Conditions ◽  
Total Carbon Content ◽  
Poor Fen ◽  
Calcareous Fen ◽  
Liparis Loeselii ◽  
The Individual ◽  
Insight Into

AbstractIn view of the sensitivity of Liparis loeselii to changes in habitat conditions, we carried out a study with the aim to monitor population numbers, identify the individual features of the Liparis loeselii population, analyse habitat conditions, identify threats and propose conservation measures to preserve the species. The investigations were conducted in seven unmanaged objects located in three Natura 2000 areas in eastern Poland. The results of this study provide a new insight into Liparis loeselii ecology. The analysed populations inhabited some habitat types: extremely poor fen, transitional mire, rich fen, calcareous fen, spring-fed fen. The content of nutrients was similar in all the habitats. A CCA analysis revealed that the total carbon content, pH, and redox potential of the substrate determine differences between the habitats analysed. Juvenile individuals represented a maximum of 12% of the analysed populations and were the least abundant group of these plants. The flowering was primarily influenced by hydrological conditions. Based on the long-term observations reported in this article, it can be assumed that the species stands a chance of surviving at the localities analysed, provided that the habitat conditions do not change dramatically.

scholarly journals Archaeal ammonia oxidizers respond to soil factors at smaller spatial scales than the overall archaeal community does in a high Arctic polar oasis

2016 ◽  
Vol 62 (6) ◽  
pp. 485-491 ◽  
Author(s):  
Samiran Banerjee ◽  
Nabla Kennedy ◽  
Alan E. Richardson ◽  
Keith N. Egger ◽  
Steven D. Siciliano
Keyword(s):  
Community Structure ◽  
Spatial Scales ◽  
Archaeal Community ◽  
Diversity Indices ◽  
High Arctic ◽  
Total Carbon ◽  
Spatial Dependency ◽  
Edaphic Factors ◽  
Total Carbon Content ◽  
Arctic Soils

Archaea are ubiquitous and highly abundant in Arctic soils. Because of their oligotrophic nature, archaea play an important role in biogeochemical processes in nutrient-limited Arctic soils. With the existing knowledge of high archaeal abundance and functional potential in Arctic soils, this study employed terminal restriction fragment length polymorphism (t-RFLP) profiling and geostatistical analysis to explore spatial dependency and edaphic determinants of the overall archaeal (ARC) and ammonia-oxidizing archaeal (AOA) communities in a high Arctic polar oasis soil. ARC communities were spatially dependent at the 2–5 m scale (P < 0.05), whereas AOA communities were dependent at the ∼1 m scale (P < 0.0001). Soil moisture, pH, and total carbon content were key edaphic factors driving both the ARC and AOA community structure. However, AOA evenness had simultaneous correlations with dissolved organic nitrogen and mineral nitrogen, indicating a possible niche differentiation for AOA in which dry mineral and wet organic soil microsites support different AOA genotypes. Richness, evenness, and diversity indices of both ARC and AOA communities showed high spatial dependency along the landscape and resembled scaling of edaphic factors. The spatial link between archaeal community structure and soil resources found in this study has implications for predictive understanding of archaea-driven processes in polar oases.

Performance of intermittent aeration reactor on NH4-N removal from groundwater resources

2010 ◽  
Vol 61 (12) ◽  
pp. 3061-3069 ◽  
Author(s):  
W. Khanitchaidecha ◽  
T. Nakamura ◽  
T. Sumino ◽  
F. Kazama
Keyword(s):  
Removal Rate ◽  
Groundwater Resources ◽  
Ammonium Nitrogen ◽  
Total Carbon ◽  
Intermittent Aeration ◽  
Reactor Performance ◽  
Total Carbon Content ◽  
Term Operation ◽  
N Removal ◽  
Synthetic Groundwater

To study the effect of intermittent aeration period on ammonium–nitrogen (NH4-N) removal from groundwater resources, synthetic groundwater was prepared and three reactors were operated under different conditions – “reactor A” under continuous aeration, “reactor B” under 6 h intermittent aeration, and “reactor C” under 2 h intermittent aeration. To facilitate denitrification simultaneously with nitrification, “acetate” was added as an external carbon source with step-wise increase from 0.5 to 1.5 C/N ratio, where C stands for total carbon content in the system, and N for NH4-N concentration in the synthetic groundwater. Results show that complete NH4-N removal was obtained in “reactor B” and “reactor C” at 1.3 and 1.5 C/N ratio respectively; and partial NH4-N removal in “reactor A”. These results suggest that intermittent aeration at longer interval could enhance the reactor performance on NH4-N removal in terms of efficiency and low external carbon requirement. Because of consumption of internal carbon by the process, less amount of external carbon is required. Further increase in carbon in a form of acetate (1.5 to 2.5 C/N ratios) increases removal rate (represented by reaction rate coefficient (k) of kinetic equation) as well as occurrence of free cells. It suggests that the operating condition at reactor B with 1.3 C/N ratio is more appropriate for long-term operation at a pilot-scale.

Sign in / Sign up

Export Citation Format

Share Document