scholarly journals Analysis of Influence of the Welding Procedure on Impact Toughness of Welded Joints of the High-Strength Low-Alloyed Steels

2020 ◽  
Vol 10 (7) ◽  
pp. 2205 ◽  
Author(s):  
Andreja Ilić ◽  
Ivan Miletić ◽  
Ružica R. Nikolić ◽  
Vesna Marjanović ◽  
Robert Ulewicz ◽  
...  
Keyword(s):  
Impact Toughness ◽  
Welded Joints ◽  
Hsla Steel ◽  
High Strength ◽  
Inert Gas ◽  
Welding Technology ◽  
First Case ◽  
Low Alloyed Steel ◽  
Welding Procedure ◽  
The Impact

This paper presents results of comparison of two welding procedures’ influence on selected properties of the welded joints of high-strength low-alloyed steel (HSLA), specifically the impact toughness and the hardness distribution in the specific zones of “single V” butt multiple-pass welded joints. Based on results obtained from experiments, the two applied welding technologies were evaluated. They differ by the welding grove geometry and by the applied root pass welding procedure. Both procedures use MAG (Metal Active Gas) welding for execution of the filling and covering passes, while the root passes are executed by the MMA (Manual Metal Arc) procedure in the first case and by the MIG (Metal Inert Gas) procedure in the second. Experimentally obtained values of the fracture energy of the welded samples for both procedures were smaller than the values for the parent metal, which confirms the fact that welding causes degradation of the mechanical properties of HSLA steel; thus, any welding technology parameters must be so selected to mitigate this deficiency.

scholarly journals Analysis of Selected Properties of Welded Joints of the HSLA Steels

Materials ◽  
2020 ◽  
Vol 13 (6) ◽  
pp. 1301 ◽  
Author(s):  
Ivan Miletić ◽  
Andreja Ilić ◽  
Ružica R. Nikolić ◽  
Robert Ulewicz ◽  
Lozica Ivanović ◽  
...  
Keyword(s):  
Impact Toughness ◽  
Welded Joints ◽  
Welded Joint ◽  
High Strength ◽  
Hardness Distribution ◽  
Micro Hardness ◽  
Hsla Steels ◽  
Applied Technology ◽  
Welding Procedure ◽  
The Impact

This paper presents research of the impact toughness and hardness distribution in specific zones of a ‘single V’butt multiple-pass welded joints of the high-strength low-alloyed steels. Obtained values of the impact toughness are analyzed in correlation with a microstructure in specific zones of the welded joint, together with the micro hardness distribution found in the related zones. Based on the carried out analysis and results obtained in experiments, the applied technology of welding was evaluated. The original conclusions on influence of the selected welding procedure manual metal arc (MMA) for the root passes and metal active gas (MAG) for the filling and covering passes) on impact toughness of the high-strength low-alloyed steels are drawn. The paper also presents discussion on the valid standards and recommendations related to welding of those steels, from the aspect of applications in design of steel welded constructions.

Investigations on the impact toughness of HSLA steel arc welded joints

2016 ◽  
Vol 21 ◽  
pp. 75-86 ◽  
Author(s):  
Rishi Pamnani ◽  
T. Jayakumar ◽  
M. Vasudevan ◽  
T. Sakthivel
Keyword(s):  
Impact Toughness ◽  
Welded Joints ◽  
Hsla Steel ◽  
The Impact

scholarly journals Effect of weld metal composition on impact toughness properties of shielded metal arc welded ultra-high hard armor steel joints

2020 ◽  
Vol 29 (1) ◽  
pp. 186-194
Author(s):  
V. Balaguru ◽  
Visvalingam Balasubramanian ◽  
P. Sivakumar
Keyword(s):  
Impact Toughness ◽  
Weld Metal ◽  
Welded Joints ◽  
Weight Ratio ◽  
High Hardness ◽  
High Strength ◽  
Solidification Mode ◽  
Austenitic Phase ◽  
Ferrite Number ◽  
Steel Joints

AbstractNowadays, ultra-high hard armor (UHA) steels are employed in armor tracked vehicle (ATV) construction because of their high hardness, high strength to weight ratio, and excellent toughness. UHA steels are usually welded using austenitic stainless steel (ASS) welding consumables, to avoid hydrogen-induced cracking (HIC). The use of ASS consumables to weld the above steel was the only available remedy because of higher solubility of hydrogen in the austenitic phase. In this investigation, an attempt was made to investigate the effect of ASS consumables (with different Creq/Nieq ratio) on solidification mode, impact toughness and microstructural characteristics of shielded metal arc (SMA) welded UHA steel joints. The welded joints were characterised based on impact toughness properties, hardness, and microstructural features. As the ferrite number increases with an increase in Creq/Nieq ratio result in different solidification mode (A, FA, F). It is also found that ferrite number of weld metal has appreciable influence on impact toughness and has inversely proportional relationship with impact toughness of the welded joints.

scholarly journals Tempforming as an Advanced Processing Method for Carbon Steels

Metals ◽  
2020 ◽  
Vol 10 (12) ◽  
pp. 1566
Author(s):  
Anastasiya Dolzhenko ◽  
Rustam Kaibyshev ◽  
Andrey Belyakov
Keyword(s):  
Impact Toughness ◽  
Crack Propagation ◽  
Large Strain ◽  
High Strength ◽  
Close Relation ◽  
Carbon Steels ◽  
Processing Method ◽  
Propagation Mode ◽  
Displacement Curve ◽  
The Impact

The microstructural mechanisms providing delamination toughness in high-strength low-alloyed steels are briefly reviewed. Thermo-mechanical processing methods improving both the strength and impact toughness are described, with a close relation to the microstructures and textures developed. The effect of processing conditions on the microstructure evolution in steels with different carbon content is discussed. Particular attention is paid to tempforming treatment, which has been recently introduced as a promising processing method for high-strength low-alloyed steel semi-products with beneficial combination of strength and impact toughness. Tempforming consists of large strain warm rolling following tempering. In contrast to ausforming, the steels subjected to tempforming may exhibit an unusual increase in the impact toughness with a decrease in test temperature below room temperature. This phenomenon is attributed to the notch blunting owing to easy splitting (delamination) crosswise to the principle crack propagation. The relationships between the crack propagation mode, the delamination fracture, and the load-displacement curve are presented and discussed. Further perspectives of tempforming applications and promising research directions are outlined.

Physical Simulation of Weldability of Weldox 1300 Steel

2013 ◽  
Vol 762 ◽  
pp. 551-555 ◽  
Author(s):  
Marek Stanislaw Węglowski ◽  
Marian Zeman ◽  
Miroslaw Lomozik
Keyword(s):  
Mechanical Properties ◽  
Impact Toughness ◽  
Physical Simulation ◽  
High Strength ◽  
Parent Material ◽  
Cooling Time ◽  
Electron Microscopies ◽  
Transmission Electron ◽  
Transformation Diagrams ◽  
The Impact

In the present study, the investigation of weldability of new ultra-high strength - Weldox 1300 steel has been presented. The thermal simulated samples were used to investigate the effect of welding cooling time t8/5 on the microstructure and mechanical properties of the heat affected zone (HAZ). In the frame of these investigation the microstructure was studied by the light (LM) and transmission electron microscopies (TEM). It has been shown that the microstructure of the Weldox 1300 steel is composed of tempered martensite, and inside the laths the minor precipitations mainly V(CN) and molybdenum carbide Mo2C were observed. Mechanical properties of parent material were analysed by the tensile, impact and hardness tests. In details the influence of cooling time in the range of 2,5 - 300 s. on hardness, impact toughness and microstructure of simulated HAZ was studied by using welding thermal simulation test. The results show that the impact toughness and hardness decrease with the increase of t8/5 under the condition of a single thermal cycle in simulated HAZ. The continuous cooling transformation diagrams (CCT-W for welding conditions) of Weldox 1300 steel for welding purposes was also elaborated. The steel Weldox 1300 for cooling time in the range of 2,5 - 4 s showed martensite microstructure, for time from 4 s to 60 s mixture of martensite and bainite, and for longer cooling time mixture of ferrite, bainite and martensite. The results indicated that the weldability of Weldox 1300 steel is limited and to avoid the cold cracking the preheating procedure or medium net linear heat input should be used.

Design of a novel HSLA steel with a combination of high strength (140–160 ksi) and excellent toughness

2021 ◽  
Vol 112 (10) ◽  
pp. 800-811
Author(s):  
Mehdi Soltan Ali Nezhad ◽  
Sadegh Ghazvinian ◽  
Mahmoud Amirsalehi ◽  
Amir Momeni
Keyword(s):  
Impact Toughness ◽  
Yield Strength ◽  
Hsla Steel ◽  
Charpy Impact ◽  
High Strength ◽  
Controlled Rolling ◽  
The Other ◽  
Grain Structure ◽  
Charpy Impact Toughness ◽  
Fine Grain

Abstract Three steels were designed based on HSLA-100 with additional levels of Mn, Ni, Cr and Cu. The steels were prepared by controlled rolling and tempered at temperatures in range of 550–700°C. The continuous cooling time curves were shifted to longer times and lower temperatures with the increased tendency for the formation of martensite at lower cooling rates. The microstructures revealed that controlled rolling results in austenite with uniform fine grain structure. The steel with the highest amount of Mn showed the greatest strength after tempering at 750 °C. The top strength was attributed to the formation of Cu-rich particles. The steel with 1.03 wt.% Mn, tempered at 650 °C exhibited the best Charpy impact toughness at –85°C. On the other hand, the steel that contained 2.11 wt.% Mn and tempered at 700 °C showed the highest yield strength of 1 097.5 MPa (∼159 ksi) and an impact toughness of 41.6 J at –85°C.

Effect of Welding Processes with High Heat Input on the Microstructure and Toughness of Coarse-Grained Heat-Affected Zone of a High-Strength High-Toughness Steel

2018 ◽  
Vol 937 ◽  
pp. 61-67
Author(s):  
Yu Jie Li ◽  
Jin Wei Lei ◽  
Xuan Wei Lei ◽  
Oleksandr Hress ◽  
Kai Ming Wu
Keyword(s):  
Low Temperature ◽  
Impact Toughness ◽  
Heat Affected Zone ◽  
Heat Input ◽  
High Strength ◽  
High Heat ◽  
Coarse Grained ◽  
Low Temperature Impact Toughness ◽  
The Impact ◽  
Welding Processes

Utilizing submerged arc welding under heat input 50 kJ/cm on 60 mm thick marine engineering structure plate F550, the effect of preheating and post welding heat treatment on the microstructure and impact toughness of coarse-grained heat-affected zone (CGHAZ) has been investigated. The original microstructure of the steel plate is tempered martensite. The yield and tensile strength is 610 and 660 MPa, respectively. The impact absorbed energy at low temperature (-60 °C) at transverse direction reaches about 230~270 J. Welding results show that the preheating at 100 °C did not have obvious influence on the microstructure and toughness; whereas the tempering at 600 °C for 2.5 h after welding could significantly reduce the amount of M-A components in the coarse-grained heat-affected zone and thus improved the low temperature impact toughness.

scholarly journals Evaluation of Microstructure and Impact Toughness of Shielded Metal Arc Dissimilar Weldments of High Strength Low Alloy Steel and Austenitic Stainless Steel

2020 ◽  
Vol 5 (2) ◽  
Author(s):  
Misbahu A Hayatu ◽  
Emmanuel T Dauda ◽  
Ola Aponbiede ◽  
Kamilu A Bello ◽  
Umma Abdullahi
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Impact Toughness ◽  
Impact Energy ◽  
High Strength ◽  
Impact Testing ◽  
Welding Parameters ◽  
Dissimilar Weld ◽  
Weld Joints ◽  
The Impact

There is a growing interest for novel materials of dissimilar metals due to higher requirements needed for some critical engineering applications. In this research, different dissimilar weld joints of high strength low alloy (HSLA) and 316 austenitic stainless steel grades were successfully produced using shielded metal arc welding (SMAW) process with 316L-16 and E7018 electrodes. Five variations of welding currents were employed within the specified range of each electrode. Other welding parameters such as heat inputs, welding speeds, weld sizes, arc voltages and time of welding were also varied. Specimens for different weld joint samples were subjected to microstructural studies using optical and scanning electron microscopes. The impact toughness test was also conducted on the samples using Izod impact testing machine. The analysis of the weld microstructures indicated the presence of type A and AF solidification patterns of austenitic stainless steels. The results further showed that the weld joints consolidated with E7018 electrode presented comparatively superior impact energy to the weldments fabricated by 316L-16 electrode. The optimum impact energy of E7018-weld joints (51J) was attained at higher welding heat inputs while that of 316L-16-weld joints (35J) was achieved at lower welding heat inputs, which are necessary requirements for the two electrodes used in the experiment. Hence, the dissimilar weld joints investigated could meet requirement for engineering application in offshore and other critical environments.Keywords—Dissimilar metal weld, heat input, impact toughness, microstructures

scholarly journals Microstructure and Impact Toughness of Local-Dry Keyhole Tungsten Inert Gas Welded Joints

Materials ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1638 ◽  
Author(s):  
Shuwan Cui ◽  
Zhiyong Xian ◽  
Yonghua Shi ◽  
Baoyi Liao ◽  
Tao Zhu
Keyword(s):  
Impact Toughness ◽  
Weld Metal ◽  
Welded Joint ◽  
Coincidence Site Lattice ◽  
Random Phase ◽  
Inert Gas ◽  
Phase Boundaries ◽  
Site Lattice ◽  
Underwater Welding ◽  
The Impact

In this paper, the microstructure and impact toughness of a S32101 duplex stainless steel underwater local-dry keyhole tungsten inert gas welded joint were studied. The impact toughness value of the underwater weld metal reached 78% of the onshore weld metal, which is in accordance with the underwater welding standards. The proportion of austenite in the underwater weld metal was 0.9% lower than that of the onshore weld metal. The proportion of the Σ3 coincidence site lattice boundaries and random phase boundaries in the underwater weld metal, which significantly influence the impact toughness of the weld metal, were smaller than that of the onshore weld metal.

Sign in / Sign up

Export Citation Format

Share Document